DeVilbiss Compact Series User manual

EP 1 - 12

SB-E-2-530

Operation Manual

HVLP and Trans-Tech®Pressure Feed

Spraygun

ISS.04

Operation Manual

COMPACT – Pressure Feed Spraygun

Important

Read and follow all instructions and Safety Precautions before using this

equipment

Description

The Compact pressure feed Spraygun Kit complies to ATEX regulations 94/9/EC, protection

level; II 2 G X, Suitable for use in Zones 1 and 2

Important: : These Sprayguns are suitable for use with both waterbased and solvent based

coating materials. The design uses EPA compliant (Devilbiss Trans-Tech®) and HVLP

atomising technology to reduce overspray and improve coating efficiency. These guns are not

designed for use with highly corrosive and/or abrasive materials and if used with such materials

it must be expected that the need for cleaning and/or replacement of parts will be increased. If

there is any doubt regarding the suitability of a specific material contact your local Distributor or

ITW Finishing direct.

Model Part Number

Example: COM-P522B-14

Aircap Fluid nozzle size

(14 = 1,4 mm)

Gunbody Finish

B= Blue Anodised

ITW Finishing Systems and Products reserve the right to modify equipment specification without

prior notice.

EC Declaration of Conformity

We: ITW Finishing UK, Ringwood Rd, Bournemouth, Dorset, BH11 9LH, UK, as the

manufacturer of the Spraygun model Compact, declare, under our sole responsibility, that the

equipment to which this document relates is in conformity with the following standards or other

normative documents:

BS EN 292-1 PARTS 1 & 2: 1991, BS EN 1953: 1999; and thereby conform to the

protection requirements of Council Directive 98/37/EC relating to Machinery Safety Directive,

and;

EN 13463-1:2001, council Directive 94/9/EC relating to Equipment and Protective

Systems intended for use in Potentially Explosive Atmospheres protection level II 2 G X.

This product complies with the requirements of the EPA guidelines, PG6/34,PG6/20 and

PG6/23. Achieving transfer efficiency in excess of 65%.

B. Holt, General Manager

30th June 2003

SAFETY WARNINGS

Fire and explosion

Solvents and coating materials

can be highly flammable or

combustible when sprayed. ALWAYS

refer to the coating material suppliers

instructions and COSHH sheets

before using this equipment

Users must comply with all local

and national codes of practice

and insurance company

requirements governing

ventilation, fire precautions, operation

and house-keeping of working areas

This equipment, as supplied,

is NOT suitable for use with

Halogenated Hydrocarbons.

Static Electricity can be

generated by fluid and/or air

passing through hoses, by the

spraying process and by cleaning non-

conductive parts with cloths. To prevent

ignition sources from static discharges,

earth continuity must be maintained to

the spraygun and other metallic

equipment used. It is essential to use

conductive air and/or fluid hoses.

Personal Protective

Equipment

Toxic vapours – When sprayed,

certain materials may be

poisonous, create irritation or be

otherwise harmful to health.

Always read all labels and safety data

sheets for the material before spraying

and follow any recommendations. If In

Doubt, Contact Your Material Supplier

The use of respiratory protective

equipment is recommended at all

times. The type of equipment

must be compatible with the material

being sprayed.

Always wear eye protection when

spraying or cleaning the spraygun

Gloves must be worn when

spraying or cleaning the

equipment

Training – Personnel should be given

adequate training in the safe use of

spraying equipment.

Misuse

Never aim a spraygun at any part of the

body

Never exceed the max. recommended

safe working pressure for the equipment

The fitting of non-recommended or non-

original spares may create hazards

Before cleaning or maintenance, all

pressure must be isolated and relieved

from the equipment

The product should be cleaned using a

gun washing machine. However, this

equipment should not be left inside gun

washing machines for prolonged periods

of time.

Noise Levels

The A-weighted sound level of

sprayguns may exceed 85 dB

(A) depending on the set-up

being used. Details of actual

noise levels are available on request. It is

recommended that ear protection is worn

at all times when spraying.

Operating

Spray Equipment using high pressures

may be subject to recoil forces. Under

certain circumstances, such forces could

result in repetitive strain injury to the

operator.

Parts List

Ref. No Description Part Number Qty Options

1 Air Cap/Retaining ring

COM-522 or COM-510

SP-100-***-K 1 522, 510, 505,523

e.g *** = 522

+ 2 Nozzle SP-200S-**-K 1 085,10,11,12,13,14,

16,18,20,22

e.g ** =14 =1.4 mm

+ 3 Separator SP-623-K5 5

+ 4 Packing GTI-445-K2 2

5 Spreader Valve SP-401-K 1

6 Stud and Screw GTI-408-K5 5

7 Needle Adjusting Screw SP-614-K 1

+ 8 Spring SP-622-K5 1

Needle SP-300S-**-K 1 085,10,11,12,13,14,

16,18,20,22

e.g ** =14 =1.4 mm

Needle—Plastic tipped SP-300P-**-K 10, 12, 14

e.g ** =14 =1.4mm

10 Airvalve housing + seal SP-612-K 1

+ 11 Spindle 1

12 Trigger SP-617-K 1

13 Connector SP-611-K 1

14 Airflow Valve SP-402-K 1

15 Fluid Inlet Connector and

seal

SP-610–K 1

+ 16 Air Valve Service Kit SPK-101-K 1

17 Retaining Ring and Seals SPK-102-K 1

+ 18 Spreader/ Cheater

Service Kit

Gti-428-K5 5

19 Circlip 25746-007-K5 5

+ 20 Air valve assembly Tool - 1

21 Spanner SPN-5 1

Spraygun Service Kit

(parts included marked + )

SPK-401-** 1 085,10,11,12,13,14,

16,18,20,22

e.g ** =14 =1.4 mm

Specification

Patent No 2372465 (GB)

Air supply connection - Universal 1/4“ BSP and NPS

Fluid Supply Connection - Universal 3/8“ BSP and NPS

Maximum static Air inlet pressure - P1= 12 bar (175 psi)

Maximum static Fluid inlet pressure - P2= 15 bar (218 psi)

Nominal gun Air inlet pressure -

with gun triggered

2.5 bar (36 psi) 523 Trans-Tech Air Cap

2. bar (29 psi) 522 & 510 Trans-Tech Air Cap

1.4 bar (20 psi) 505 HVLP Air Cap

Maximum Service temperature 40°C

Gun Weight - 435 g

Materials of Construction

Gun body Anodised Aluminium

Nozzle Stainless Steel

Needle Stainless Steel

Fluid Inlet Stainless Steel / PTFE

Trigger Nickel Plated Steel

Installation

Important: To ensure that this

equipment reaches you in first class

condition, protective coatings have

been used. Flush the equipment

through with a suitable solvent

before use.

1. Attach air hose to connector (13).

Recommended hose size 8 mm

bore. The hose must be conductive

and electrical bond from the

spraygun to earth should be

checked with an ohmeter. A

resistance of less than 106Ohms is

recommended.

2 Attach fluid supply hose to Fluid

Inlet (15).

1. Turn off air and coating supply and

relieve pressure in the supply lines,

or if using QD system, disconnect

from airline and fluid line.

2. Remove air cap (1) and clean. If

any of the holes in the cap are

blocked with coating material use a

toothpick to clean. Never use metal

wire which could damage the cap

and produce distorted spray

patterns

3. Ensure the tip of the nozzle (2) is

clean and free from damage. Build

up of dried paint can distort the

spray pattern.

4. Lubrication – stud/screw (6), needle

(9) and air valve (11) should be

oiled each day.

Preventative Maintenance

Operation

1. Mix coating material to

manufacturers instructions

2. Turn needle adjusting screw (7)

clockwise to prevent movement.

3. Turn spreader valve (5) counter-

clockwise to fully open.

4. Adjust inlet air pressure (For

recommended figures see

Specifications) at the gun inlet with

the gun triggered. (pressure gauge

attachment shown under

Accessories is recommended for

this).

5. Turn needle adjusting screw counter

clockwise until first thread shows.

6. Test spray. If the finish is too dry

reduce airflow by reducing air inlet

pressure or by the Airflow Valve (14).

Screw the Adjusting Knob (14) in to

reduce pressure.

7. If finish is too wet reduce fluid flow

by turning needle screw (7)

clockwise or reducing the fluid

pressure. If atomisation is too

coarse, increase inlet air pressure. If

too fine reduce inlet pressure.

8. The pattern size can be reduced by

turning adjusting valve (5) clockwise.

9. Hold gun perpendicular to surface

being sprayed. Arcing or tilting may

result in uneven coating.

10. The recommended spray distance is

150-200 mm (6”-8”).

11. Spray edges first. Overlap each

stroke a minimum of 50%. Move gun

at a constant speed.

12. Always turn off air and fluid supply

and relieve pressure when gun is not

in use.

Nozzle (2) and Needle (9) – Remove

parts in the following order: 7, 8, 9, 1

and 2. Replace any worn or damaged

parts and re-assemble in reverse order.

Recommended tightening torque for

nozzle (2) 9.5-12 Nm (80-100 lbf in).

Packing – Remove parts 7, 8, 9.

Unscrew cartridge (4). Fit new cartridge

finger tight. Re-assemble parts 9, 8,

and 7 and tighten cartridge (4) with

spanner sufficient to seal but to allow

free movement of needle. Lubricate

with gun oil.

Air Valve Seal Kit (16) - (Refer to

photos 1 to 28 and fig 2)

1. Remove Adjusting Knob (7), Spring

(8), and Needle (9).

2. Loosen Housing (10).

3. Remove Housing (10) and Airvalve

Spring.

4. Remove Valve (11).

5. Using Service Tool SPN-7, engage

groove behind the Valve Seat.

6. Remove Valve Seat.

7. Push out the Front Airvalve Seal

with a finger.

8. Turn the Gun upside down and let

the Seal fall out.

9. Fit New Front Seal to Service Tool.

10. Fit new Seal to gunbody and press

firmly to ensure Seal is engaged.

11. Fit New Valve Seat to Service Tool.

Groove must face outwards.

12. Fit Valve Seat to Gunbody.

13. Remove Rear Airvalve Seal from

housing (10) with a hooked

instrument.

14. Fit new Seal to Service Tool.

15. Fit Seal to Housing (10).

16. Replace Valve (11).

17. Replace Valve Spring and screw in

Housing (10).

18. Tighten Housing.

19. Fit Needle (9).

20. Fit Spring (8) and Knob (7).

21. Adjust Needle Packing (4) with

Spanner sufficient to seal but to

allow free movement of needle.

Lubricate with gun oil.

Spreader valve (5) – Caution: always

ensure that the valve is in the fully open

position by turning screw fully counter-

clockwise before fitting to body.

Air cap / Nozzle Selection

Refer to coating material manufacturers

recommendations or ITW Finishing UK

Website:

www.itweuropeanfinishing.com

Replacement of Parts E

FIG 2

1 2

3 4

5 6

7 8

9 10

11 11a

12 13

14 15

18 19

20 21

Other manuals for Compact Series

This manual suits for next models

Table of contents

Other DeVilbiss Paint Sprayer manuals

DeVilbiss

DeVilbiss SRI-630G User manual

DeVilbiss

DeVilbiss MSV-531-28FF Reference manual

DeVilbiss

DeVilbiss Finish Line FLG-MGQ-700-FL Reference manual

DeVilbiss

DeVilbiss CMAX-B85MN User manual

DeVilbiss

DeVilbiss GTI User manual

DeVilbiss

DeVilbiss Compact HVLP User manual

DeVilbiss

DeVilbiss Compact COM-PS430-18-01 User manual

DeVilbiss

DeVilbiss AGX-552 User manual

DeVilbiss

DeVilbiss FLG-P5-14 User manual

DeVilbiss

DeVilbiss GTI SB-2-168-N Reference manual

DeVilbiss

DeVilbiss AGX-550 User manual

DeVilbiss

DeVilbiss AGXV-540 User manual

DeVilbiss

DeVilbiss FLG-CNG-115 User manual

DeVilbiss

DeVilbiss FinishLine TGC-500-2 User manual

DeVilbiss

DeVilbiss AG360 Series User manual

DeVilbiss

DeVilbiss Cobra 2 User manual

DeVilbiss

DeVilbiss FLG-G5 User manual

DeVilbiss

DeVilbiss LUNA-R User manual

DeVilbiss

DeVilbiss SRi PRO Lite User manual

DeVilbiss

DeVilbiss JGP-504 User manual

DeVilbiss

DeVilbiss GTI User manual

DeVilbiss

DeVilbiss TGC-536 User manual

DeVilbiss

DeVilbiss JGP-503 CONVENTIONAL Reference manual

DeVilbiss

DeVilbiss SRi-628 Reference manual

Popular Paint Sprayer manuals by other brands

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Operator's manual

Graco

Graco 246737 Repair and parts

Binks

Binks SV100 Service manual

Fimco

Fimco LG-4-3-1 owner's manual

AG SPRAY

AG SPRAY FS-ATV-25BL owner's manual

Nordson

Nordson MicroMax 2 manual

Bonide

Bonide 051 Operation and service instructions

zogics

zogics Z-DAS instruction manual

KISANKRAFT

KISANKRAFT KK-KBS-165 Operation manual

Matrix

Matrix SG 650 Translation of the original instructions

Anest Iwata

Anest Iwata SGA-3 Installation, use & maintenance instruction manual

paasche

paasche VV Instructions and parts list

Carlisle

Carlisle DeVilbiss JGA-510 Service manual

Gardena

Gardena 11120 Operator's manual

Conrad

Conrad Hobby Airbrush K3 operating instructions

wiwa

wiwa 14025 R/F operating manual

Graco

Graco EM 390 Instructions-parts list

Graco

Graco HydroShield WMBH00 Instructions - parts