Desa CD32M Quick start guide

CD32M (-1)(-2), CD36M (-A1)(-A2), CD42M-A

FOR YOUR SAFETY

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch

• Do not use any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the fire

department.

SAVE THIS BOOK

This book is valuable. In addition to instructing you on

how to install and maintain your appliance, it also con-

tains information that will enable you to obtain replace-

ment parts or optional accessory items when needed.

Keep it with your other important papers.

WARNING: If the information in this manual is not

followedexactly,afireorexplosionmayresultcaus-

ing property damage, personal injury, or loss of life.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable

vaporsandliquidsinthevicinityofthisoranyother

appliance.

Save this manual for future reference.

For more information, visit www.desatech.com

DIRECT-VENT FIREPLACE

OWNER’S OPERATION AND

INSTALLATION MANUAL

WARNING: This direct-vent gas fire-

place is intended for use with natural

or propane/LP gas only. Do not at-

tempt to burn any solid fuels in this

appliance.

WARNING: Improper installation, ad-

justment,alteration,service,ormainte-

nance can cause injury or property

damage. Refer to this manual for cor-

rectinstallationandoperationalproce-

dures. For assistance or additional in-

formation consult a qualified installer,

service agency, or the gas supplier.

This fireplace is manufactured for Stylecrest Inc. under the Coleman brand name by DESA.

This fireplace may be installed as an OEM installation in a manufactured (mobile) home and

must be installed in accordance with the manufacturers instructions and the

Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280

in the United States or the

MobileHomeStandard,CAN/CSAZ240MHSeries

,inCanada.Thisfireplaceisonlyforusewith

the type(s) of gas indicated on the rating plate. A conversion kit is supplied with the fireplace.

111916-01A

For more information, visit www.desatech.com

Models CD32M sereies, CD36M-A series and CD42M-A are heat

circulating gravity direct-vent fireplaces with sealed combustion

chamber. These fireplaces use millivolt gas control valve and

millivolt ignition system.

These fireplaces are convertible with the standard setup as natural

gas. Conversion may be performed by the O.E.M. mobile home

builder or by a qualified service person on-site. If you are uncertain

astowhatgasyourunitisequippedfor,pleasechecktheratingplate

locatedinsideoftheapplianceopeningorconsultyourmobilehome

supplier or your local distributor of DESA/Coleman products.

INTRODUCTION

WARNING:Thisproductcontainsand/orgenerates

chemicals known to the State of California to cause

cancer or birth defects, or other reproductive harm.

BEFORE YOU BEGIN

Before beginning the installation of your appliance, read these

instructions through completely.

This DESA/Coleman fireplace and its components are safe when

installed according to this installation manual and operated as recom-

mended. Unless you use DESA/Coleman components designed and

tested for this fireplace system, YOU MAY CAUSE A SAFETY

HAZARD!

NOTICE:Checklocalbuildingcodesforarearequire-

ments before installing this appliance.

The DESA/Coleman warranty will be voided by, and DESA/

Coleman disclaims any responsibility for the following actions:

A) Modification to the fireplace, components, doors, blower, fans

or vent system.

B) Use of any component part not manufactured or approved by

DESA/Coleman in combination with a DESA/Coleman fire-

place system.

Proper installation is the most important step in ensuring safe and

continuous operation of the fireplace. Consult the local building

codes as to the particular requirements concerned with the installa-

tion of all factory built fireplaces. This fireplace, when installed,

must be electrically grounded in accordance with local codes, or in

theabsenceoflocalcodes,withtheNationalElectricalCode,ANSI/

NFPA 70 or the Canadian Electrical Code, CSA C22.1.

Theinstallationmust conformwithlocal codesor, in theabsence of

local codes, with the National Fuel Gas Code, ANSI Z223.1 or the

Canadian Installation Code, CAN/CGA B149. Thisappliance com-

plies with ANSI Z21.88-1998 and CSA 2.33-M98 as a VENTED

GAS FIREPLACE HEATER.

TABLE OF CONTENTS

INTRODUCTION......................................................................... 2

SELECTING LOCATION............................................................. 3

PRE-INSTALLATION PREPARATION ........................................ 3

INSTALLATION ........................................................................... 6

BURNER FLAME ADJUSTMENT ..............................................11

OPERATING FIREPLACE ........................................................ 12

CONVERTING FIREPLACE FROM NATURAL GAS

TO PROPANE/LP GAS ........................................................ 13

TROUBLESHOOTING .............................................................. 15

ILLUSTRATED PARTS BREAKDOWN AND PARTS LIST....... 16

SPECIFICATIONS .................................................................... 20

WIRING DIAGRAM ................................................................... 20

OWNER’S REGISTRATION FORM.......................................... 21

ACCESSORYAND REPLACEMENT PARTS........................... 23

TABLE OF CONTENTS

INTRODUCTION

Before You Begin

111916-01A

For more information, visit www.desatech.com

SELECTING LOCATION

To determine the safest and most efficient location for your fire-

place, consider the following guidelines:

1. The location must allow for proper clearances (see Figure 1).

2. Consider a location where the firepace would not be affected

by drafts, air conditioning ducts, windows or doors.

3. A location that avoids the cutting of joists or roof rafters makes

ventilation installation easier.

In selecting a location, the following precautions must be observed:

• Do not connect this appliance to a chimney system used for solid

fuel burning fireplace.

• Due to high temperatures, do not locate this appliance in high

traffic areas or near furniture and draperies.

• Never obstruct the openings of the appliance or flow of ventila-

tion air. Keep the control compartments accessible.

• Do not locate appliance close to where gasoline or other flam-

mable liquids may be stored. The appliance must be kept clear

and free from combustible materials.

• Do not use this appliance if any part has been under water. Imme-

diately contact a local service technician to examine the appli-

ance and to replace any part(s) of the control ignition system and

other related components that have been submerged under water.

Figure 1 - Common Fireplace Locations

Flush installation is recommended where living space is limited.

Projected installation may be ideal for a new addition to an

existing finished wall.

Cornerinstallationmakesuse of a space thatmay not normally be

used and provides a wider and more efficient range for radiant heat

transfer.

CLEARANCES TO COMBUSTIBLES

Minimum clearances to combustibles for the fireplace are:

• Back and Sides of Fireplace.................................................. 0"

• Floor ......................................................................................0"

• Perpendicular Wall ................................................................ 6"

• Front ....................................................................................36"

• Top of Standoffs ....................................................................0"

CAUTION: Do not block required air spaces with

insulation or any other material. Do not obstruct the

effective opening of the appliance with any type of

facing material.

PRE-INSTALLATION

PREPARATION

MANTEL CLEARANCES

Woodwork, such as wood trims, mantles, and other combustible

materials should be placed within the required clearance specified

in Figure 2.

Figure 2 - Mantel Clearances

FULL

PROJECTION CORNER

INSTALLATION

FLUSH

INSTALLATION

Top of Louver Opening

Wall

Mantel Mantel From Top

Depth of Opening

(1) 14" (A) 16"

(2) 12" (B) 14"

(3) 10" (C) 12"

(4) 8" (D) 10"

(5) 6" (E) 8"

(6) 4" (F) 6"

(7) 2" (G) 4"

SELECTING LOCATION

PRE-INSTALLATION PREPARATION

Clearances to Combustibles

Mantel Clearances

111916-01A

For more information, visit www.desatech.com

PRE-INSTALLATION

PREPARATION

Continued

VENT TERMINATION CLEARANCES

The final position of your fireplace depends on the location of the

vent termination in relation to the clearances that must be observed

as shown in Figure 5 on page 5.

The vent system serves as the “chimney” as well as the combustion

air supply (air intake). The horizontal run must have a rise of 1/4"

(.6 cm) for every 12" (30.48 cm) of horizontal run towards the

termination. The maximum horizontal run depends on the vertical

rise from the fireplace adapter collar to the vent termination (see

table below).

WARNING: Horizontal sections of this vent sys-

tem require a minimum clearance of 2" from the top

ofthepipeand1"minimum to the sides and bottom.

Vertical sections of this system require a minimum

of1"clearancetocombustiblematerialsonallsides

of the pipe.

VERTICAL HORIZONTAL

0 to 1 ft (30.48 cm)

1 ft (30.48 cm) to 4 ft (121.92 cm)

2 ft (60.96 cm) to 8 ft (243.84 cm)

3 ft (91.44 cm) to 12 ft (365.76 cm)

4 ft (121.92 cm) to 16 ft (487.68 cm)

5 ft (152.40 cm) to 15 ft (457.20 cm)

6 ft (182.88 cm) to 14 ft (426.72 cm)

7 ft (213.36 cm) to 13 ft (396.24 cm)

8 ft (243.84 cm) to 12 ft (365.76 cm)

WARNING: Never allowtheventtorun downward

as this may cause excessive temperatures which

could cause a fire.

CD32M CD36M-A CD42M-A

A 32 3/8" 36 1/8" 40 1/8"

B 34 5/8" 41 1/4" 48 1/4"

C 19" 23 1/2" 25 5/8"

Figure 3 - Framing Dimension

Figure 4 - Corner Installation

Nailing Tabs

CD32M CD36M-A CD42M-A

A 28 1/2" 35 3/4" 41 5/8"

B 13 5/8" 15" 21 5/8"

C 39 3/8" 49 5/8" 58 1/2"

1/2" 10 3/8" 13 1/2"

7/8" 13 3/4" 16 3/4"

F 34 1/2" 41 1/8" 48"

G 35 1/2" 42 1/8" 48 1/4"

H 54 3/8" 68 1/4" 81 1/2"

FRAMING

Once the final location has been determined, observing height clear-

ances for vent termination, you may construct framing using dimen-

sions shown in Figures 3 and 4, depending on your installation.

If the appliance is to be installed directly on carpeting, tile (other

than ceramic), or any combustible material other than wood floor-

ing, the appliance must be installed on a metal or wood panel

extending the full width and depth of the appliance.

PRE-INSTALLATION PREPARATION

Vent Termination Clearances

Framing

111916-01A

For more information, visit www.desatech.com

Fixed

Closed Openable Fixed

Closed

Openable

TERMINATION CAP AIR SUPPLY INLET GAS METER RESTRICTED AREA

(TERMINATION PROHIBITED)

A = clearance above grade, veranda, porch, deck, or balcony

[*12 inches (30.5cm) minimum]

B = clearance to window or door that may be opened

[12 inches (30.5cm) minimum]

C = clearance to permanently closed window [minimum 12 inches

(30.5cm) recommended to prevent condensation on window]

D = vertical clearance to ventilated soffit located above the terminal

within a horizontal distance of 24 inches (61cm) from the

center-line of the terminal [18 inches (45.7cm) minimum]

E = clearance to unventilated soffit [12 inches (30.5cm) minimum]

F = clearance to outside corner (see below)

G = clearance to inside corner (see below)

H = *not to be installed above a meter/regulator assembly within

36 inches (91.4cm) horizontally from the center-line of the regulator

I = clearance to service regulator vent outlet [*72 inches (182.9cm)

minimum]

J = clearance to non-mechanical air supply inlet to building or the

combustion air inlet to any other fireplace [*12 inches (30.5cm)

minimum]

K = clearance to a mechanical air supply inlet [*72 inches (182.9cm)

minimum]

L = clearance above paved side-walk or a paved driveway located on

public property [*84 inches (213.4cm) minimum]

M = clearance under veranda, porch, deck [*12 inches (30.5cm) minimum ]

N = clearance above a roof shall extend a minimum of 24 inches (61cm)

above the highest point when it passes through the roof surface and

any other obstruction within a horizontal distance of 18 inches (45.7cm)

vent shall not terminate directly above a side-walk or paved driveway which is located between two

single family dwellings and serves both dwellings*

only permitted if veranda, porch, deck or balconey is fully open on a minimum of 2 sides beneath the floor*

* as specified in CAN/SGA B149 (.1 or .2) Installation Codes (1991) for Canada or for U.S.A. installation follow

the current

National Fuel Gas Code, ANSI Z223.1

Note: Local codes or regulations may require different clearances

A = 6" (15.2cm)

Inside Corner

B = 6" (15.2cm)

C = Maximum depth of 48" (121.9cm) for

recessed location

D = Minimum width for back wall of

recessed location -

Combustible - 38" (96.5cm)

Noncombustible - 24" (61cm)

E = Clearance from corner in

recessed location-

Combustible - 6" (15.2cm)

Noncombustible - 2" (5.1cm)

Outside Corner Recessed Location

G = Combustible 24" (61cm)

Noncombustible 18" (45.7cm)

Balcony with No SideWall

Combustible &

Noncombustible

H = 24" (61cm)

J = 20" (50.8cm)

Balcony with Perpendicular Side Wall

CDC

Termination Clearances for Buildings with Combustible and Noncombustible Exteriors

Figure 5 - Minimum Clearances for Vent Terminations

PRE-INSTALLATION PREPARATION

Continued

PRE-INSTALLATION PREPARATION

111916-01A

For more information, visit www.desatech.com

VENTING INSTALLATION

1. Install elbow to fireplace collar adapter located on back of the

unit at a 45° angle. Slide elbow over collar and twist to lock.

Check to insure proper connection (see Figure 6).

2. Continue to install remainder of pipe for desired installation.

Make sure each section is twist-locked securely.

Figure 6 - Venting Installation

Figure 7 - Vent Termination (Horizontal)

Direct-Vent Pipe

CD32M and CD36M-A

4 1/4" Inner and 7 1/4" Outer

CD42M-A

5" Inner and 8" Outer

Wall

Firestop

Maintain 1" Minimum Air

Space Around Outer Pipe

when Penetrating a Wall Horizontal

Termination

(Vent Cap)

Screws

Exterior Wall with

Vinyl Siding

Deflector

Shield

Minimum Pipe

Overlap 1 1/4"

Siding Standoff

(Optional)

Framed Openings

CD32M and CD36M-A

10" x 10"

CD42M-A

10 3/4" x 10 3/4"

WARNING: Read all instructions completely and

thoroughly before attempting installation. Failure to

dosocouldresultinseriousinjury, propertydamage

or loss of life. Operation of improperly installed and

maintained venting system could result in serious

injury, property damage or loss of life.

NOTICE: Failure to follow these instructions will void

the warranty.

INSTALLATION

Female Locking Lugs

Vertical Flue Restrictor

(For Vertical Venting

Application)

Male Locking

Lugs

3. When installation of vent pipe is complete, in stall vent termi-

nation. Depending on the location of your fireplace, you will

vent vertically or horizontally.

4. Allow 1" of pipe to protrude from internal wall, depending on

wall thickness. See Figure 7.

5. For horizontal installation, an optional siding standoff may be

installed between the vent cap and the exterior wall. Secure

horizontal vent cap to standoff. Secure standoff/vent cap as-

sembly to wall (see Figure 7). Do not seal termination to vent

pipe. The vent termination must be removable for service pipe

inspection.

6. For verticalinstallation, a verticaltermination is available.Also

for vertical venting application, install vertical flue restrictor

into inner collar of fireplace as shown in Figure 6.

When installing a length of pipe for vertical termination that is

over 3 ft., support the pipe every 3 ft. using metal wall straps.

Vertical to horizontal pipe must be kept at a 1 ft. to 4 ft. ratio

with a maximum run of no more than 20 ft.

VENTING INSTALLATION PRECAUTIONS

Consult local building codes before beginning the installation. The

installer must make sure to select the proper vent system for installa-

tion. Before installing vent kit, the installer must read this fireplace

manual and vent kit instructions.

Only a qualified service person should install venting system. The

installer must follow these safety rules:

• Wear gloves and safety glasses for protection

• Use extreme caution when using ladders or when on roof tops

• Be aware of electrical wiring locations in walls and ceilings

Thefollowingactionswillvoidthe warrantyonyourventingsystem:

• Installation of any damaged venting component

• Unauthorized modification of the venting system

• Installationof any componentpart not manufacturedor approved

by DESA

• Installation other than as instructed by these instructions

WARNING: Horizontal sections of this vent sys-

tem require a minimum clearance of 2" from the top

ofthepipeand1"minimumtothesidesandbottom.

Vertical sections of this system require a minimum

of 1" clearance to combustible materials on all

sides of the pipe.

WARNING: This gas fireplace and vent assembly

must be vented directly to the outside. The venting

system must NEVER be attached to a chimney serv-

ingaseparatesolidfuelburning appliance.Eachgas

appliance must use a separate vent system. Do not

use common vent systems.

INSTALLATION

Venting Installation Precautions

Venting Installation

111916-01A

For more information, visit www.desatech.com

Figure 8 - Vertical Termination with Offset and Wall Strap

Wall Strap

Roof Flashing

45°Elbows

Ceiling Firestop

Roof Pitch Minimum Height Above Roof

Flat - 7/12 1 ft. (30.48 cm)

7/12 - 8/12 1 1/2ft. (45.72 cm)

8/12 - 9/12 2 ft (60.96 cm)

9/12 - 10/12 2 1/2ft (76.20 cm)

10/12 - 11/12 4 ft (121.92 cm)

11/12 - 14/12 5 ft (152.40 cm)

14/12 - 16/12 6 ft (182.88 cm)

16/12 - 18/12 7 ft (213.36 cm)

18/12 - 20/12 7 1/2ft (228.60 cm)

20/12 - 21/12 8 ft (243.84 cm)

INSTALLATION

Continued

ELECTRICAL HOOKUP AND REMOTE

RECEIVER DIAGRAM

Anoutlet boxwithtwo receptacles(see Figure9) hasbeensupplied

foryour convenienceandis locatedinside onthelower rightside of

the fireplace.

The remote control receiver is factory wired and connected to the

convertible gas valve as shown in Figure 10.

Figure 9 - Duplex Outlet

Three-prong Plug

GAS SUPPLY TESTING

NOTICE: This section is intended as a guide for

qualified technicians installing gas to the appliance.

WARNING: Do not connect appliance before pres-

sure testing gas piping. Damage to gas valve may

result and an unsafe condition may be created.

Theapplianceanditsindividualshutoffvalvemustbedisconnected

fromthegassupplypipingsystemduringanypressuretestingofthat

system at test pressures in excess of 1/2 psig (3.5 kPa).

The appliance must be isolated from the gas supply piping system

byclosingitsindividualshutoffvalveduringanypressuretestingof

the gas supply piping system at test pressures equal to or less than

1/2 psig (3.5 kPa).

The gas control valve is secured underneath the firebox. Two 1/8"

ports are provided on the gas control valve for pressure test gauge

connections (see Figure 11).

Figure 10 - Remote Control Receiver

Figure 11 - Gas Control Valve

16AI

TPTH TP TH

ON/OFF

Knob

Pilot Adjustment

Inlet

Pressure Outlet Pressure

Flame Adjustment Knob

Pilot Gas

Line Do

Not Kink

To Pilot Burner

To Main

Burner

Outlet Box

OFF

TPTH

REMOTEOFFON

TPTHTPTH

Remote Control

Receiver

Convertible

Gas Valve

If an offset is necessary in the attic to avoid obstruction, it

is important to support the vent pipe every 3 ft. to avoid

excessive stress on the elbows and possible separation (see

Figure 8, page 7).

Clearances must be maintained between the roof and the ter-

mination. Refer to chart below.

INSTALLATION

Venting Installation (Con.)

Electrical Gookup and Remote Reeiver Diagram

Gas Supply Testing

111916-01A

For more information, visit www.desatech.com

INSTALLATION

Continued

GAS LINE HOOK-UP

WARNING: Gas line hook-up should be done by

your gas supplier or a qualified service person.

WARNING: Before you proceed, make sure your

gas supply is OFF.

Anequipment shutoff valve has beenincluded inthe fireplace's gas

supply system. However, consider installing an extra shutoff valve

outside the appliance’s enclosure (check local codes), where it can

be accessed more conveniently with a key through a wall as shown

in Figure 12.

Inconformance withlocal codes, routea 1/2"NPT gasline towards

the appliance coming in from either the left or right side of the

fireplace (see Figure 13).

Install a sediment trap between the incoming gas line and the gas

controlbox.(seeFigure14).Thesedimenttrapshould extend down

a minimum of 3" (7.62 cm) beyond the center of the pipe.

When routing gas line through conduit sleeve, make sure to repack

insulation to fill gaps between gas line and conduit sleeve. Com-

poundsusedon threaded jointsofgas piping shallberesistant to the

action of propane or natural gas. Compounds should be applied

lightly to ensure excess sealant does not enter the gas line.

WARNING: All gas piping and connections must

betestedfor leaks aftertheinstallationiscompleted.

Never use an open flame to check for a leak. After

ensuring that the gasvalve is open apply commercial

leak detection fluid to all gas joints. Bubbles forming

show a leak. Correct all leaks at once.

Do not operate any appliance if a leak is detected.

Figure 12- Typical Exterior Wall Gas Shutoff Installation

Key

Extension

Shutoff Valve

Figure 13 - Gas Line Routing

Figure 14 - Sediment Trap

PILOT ADJUSTMENT

Thepilotorelectrodeassemblyisfactorypresetfortheproperflame

height. Alterations to these settings may have occurred during

shippingandhandling.Ifthisisthecase,someminor readjustments

may be necessary and should be done by a qualified service

technician. The proper settings for the thermopile height should be

at a distance of 3/8" (.95 cm) to 1/2" (1.27 cm) from the pilot flame

as shown in Figure 15.

Figure 15 - Pilot Assembly

3" Min.

Sediment Trap

(Not Supplied)

Incoming 1/2" Gas

Line Permitted By

Local Codes

3" Min.

(7.6 cm)

1/8"

(0.3cm) 3/8" - 1/2"

(.95cm-1.3cm)

Complete your gas line installation by connecting the incoming

gas line to the flexible gas line. Secure tightly with a wrench but

do not over-tighten.

OFF

TPTHTPTH

Gas Routing

(Right Side Not Shown)

Side of

Fireplace

Front Face

INSTALLATION

Gas Line Hook-Up

Pilot Adjustment

111916-01A

For more information, visit www.desatech.com

INSTALLATION

Continued

REMOVING GLASS PANEL

CAUTION: Before you proceed, make sure your

gas control valve is in the OFF position.

1. To remove louvers, pull both spring latches (located in each

end of louver) toward center of appliance at the same time

until disengaged from locating holes. Repeat for bottom end

spring latches (see Figure 16).

2. Remove screen rod by removing rod loop from glass door center

bracket.Slidescreen rodeitherto theleftor rightoffireplace until

one end is free to completely remove screen from fireplace.

3. Undo latches located on top and bottom of firebox (see Figure

17). Carefully swing door to the left. The glass door is se-

curely mounted to the firebox with 5 screws.

Figure 16 - Removing Louvers

Figure 17 - Spring Latches

INSTALLING LOG SET

Each log is marked with a number in the following diagram. These

numbers will help in identifying the logs when installed. It is very

important to install these logs exactly as instructed. Do not modify

logs. Only use logs supplied with fireplace.

Models CD32M and CD36M-A Series

1. Place log #1 (back log) on top of grate as shown in Figure 18.

Make sure notches in bottom of log fit over grate.

2. Place log #2 (large front log) over pins on grate (see Figure 19).

Figure 18 - Installing Log #1,

Models CD32M/CD36M-A

Series

Figure 19 - Installing Log #2,

ModelsCD32M/CD36M-ASeries

Glass Locating

Holes

Spring

Latch

Bottom

Louver

Open Close

3. Place log #3 (c-shaped crossover log) onto rear and front logs

as shown in Figure 20. Make sure it is seated properly on the

smooth surface on front log and on the pin on back log.

4. Place log #4 (small round log) on pin on right side of front log

(see Figure 21).

5. Place log #5 (small front log) onto the front left part of grate

making sure notches fit over prongs of grate (see Figure 22).

6. Place log #6 onto two pins on left side of back and front logs

(see Figure 22).

Figure 20 - Installing Log #3,

Models CD32M/CD36M-A

Series

Figure 21 - Installing Log #4,

Models CD32M/CD36M-A

Series

Figure 22 - Installing Logs #5 and #6, Models CD32M/CD36M-A

Series

INSTALLATION

Removing Glass Panel

Installin Log Set

111916-01A

For more information, visit www.desatech.com

INSTALLATION

Continued

Figure 23 - Installing Log #1, Model CD42M-A

Figure 24 - Installing Log #2, Model CD42M-A

Figure 25 - Installing Log #3, Model CD42M-A

Figure 26 - Installing Log #4, Model CD42M-A

Figure 27 - Installing Log #5, Model CD42M-A

Figure 28 - Installing Logs #6 and #7, Model CD42M-A

Model CD42M-A

1. Place log #1 (small base log) onto pin on left side of grate

extension (see Figure 23).

2. Rest left side of log #2 (front log) on top of log #1 and right

side onto pin located on right side of grate extension (see Fig-

ure 24).

3. Place log #3 (rear log) onto pins on rear of grate (see Figure 25).

4. Place log #4 (crossover log) onto pins from both logs #2 and

#3 (see Figure 26).

5. Place log#5 (toplog) onto right pin offront log(#2) and smooth

surface of rear log (#3). Make sure it is seated properly (see

Figure 27).

6. Place log #6 (left log) on left pin of front log (#2) and smooth

surface of rear log (#3). Make sure it is seated properly (see

Figure 28).

7. Place log #7 (right log) on right pin of top log (#5). Make sure

it is seated properly (see Figure 28).

INSTALLATION

Installing Log Set (Cont.)

This manual suits for next models

Table of contents

Other Desa Indoor Fireplace manuals

Desa

Desa CGEFP33NRB Quick start guide

Desa

Desa MSVFBNR Series Quick start guide

Desa

Desa CGEF26A Original instructions

Desa

Desa Comfort Glow CF26NT Quick start guide

Desa

Desa RFN28TB Quick start guide

Desa

Desa Vanguard VMH26TNB Quick start guide

Desa

Desa VDVF36PN/PP Quick start guide

Desa

Desa Comfort Glow LFP33NR Quick start guide

Desa

Desa GMC11FD Instruction manual

Desa

Desa "TUDOR" VT32N-A Series Quick start guide

Desa

Desa S42 Series Quick start guide

Desa

Desa VKC42N Series Quick start guide

Desa

Desa VDCFTNB Quick start guide

Desa

Desa VsGF28nTF Quick start guide

Desa

Desa P324E Quick start guide

Desa

Desa A Series Quick start guide

Desa

Desa V50S Quick start guide

Desa

Desa Comfort Glow CGCF26TN Quick start guide

Desa

Desa EFS33NRA Quick start guide

Desa

Desa CVDA24M User manual

Desa

Desa Comfort Glow CGFP28P User manual

Desa

Desa Vanguard VGL450N Quick start guide

Desa

Desa VICTORIAN VV36ENB SERIES Quick start guide

Desa

Desa HEARTH CDCFTN Quick start guide

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Miles Industries

Miles Industries Vogue 1300IRN Installation & operating instructions