Desa HD18NRA Quick start guide

For more information, visit www.desatech.com

WARNING: If the information in this manual is not

followed exactly, a re or explosion may result causing

property damage, personal injury or loss of life.

— Do not store or use gasoline or other ammable

vapors and liquids in the vicinity of this or any other

appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re

department.

— Installation and service must be performed by a quali-

ed installer, service agency or the gas supplier.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

UNVENTED (VENT-FREE) GAS LOG HEATER

OWNER’S OPERATION AND INSTALLATION MANUAL

18" AND 24" REMOTE CONTROL READY MODELS

HD18NRA, HD18PRA, HD24NRA AND HD24PRA

Patent Pending

Also Design Certied As

Vented Decorative Appliances

www.desatech.com 123167-01D2

SAFETY

WARNING: Improper

installation, adjustment,

alteration,serviceormain-

tenance can cause injury

or property damage. Refer

to this manual for correct

installation and operation-

al procedures. For assis-

tance or additional infor-

mation consult a qualied

installer, service agency

or the gas supplier.

WARNING: This ap-

pliance is for installation

only in a solid-fuel burn-

ing masonry or UL127

factory-built fireplace or

in a listed ventless rebox

enclosure. It is design-cer-

tied for these installations

in accordance with ANSI

Z21.11.2. Exception: Do not

install this appliance in a

factory-built replace that

includes instructions stat-

ing it has not been tested

or should not be used with

unvented gas logs.

WARNING: This is an

unvented gas-red heat-

er. It uses air (oxygen)

from the room in which

it is installed. Provisions

for adequate combustion

and ventilation air must

be provided. Refer to Air

for Combustion and Ven-

tilation section on page 6

of this manual.

This appliance may be in-

stalled in an aftermarket,*

permanently located,

manufactured (mobile)

home, where not prohib-

ited by local codes.

This appliance is only for

use with the type of gas

indicated on the rating

plate. This appliance is

not convertible for use

with other gases.

* Aftermarket: Completion of sale, not for

purpose of resale, from the manufacturer

TABLE OF CONTENTS

Safety .................................................................. 2

Product Identication........................................... 5

Local Codes......................................................... 5

Unpacking............................................................ 5

Product Features................................................. 5

Air For Combustion and Ventilation ..................... 6

Installation ........................................................... 8

Operation........................................................... 18

Inspecting Burners............................................. 22

Cleaning and Maintenance................................ 22

Specications .................................................... 23

Troubleshooting................................................. 24

Technical Service............................................... 28

Service Hints ..................................................... 28

Replacement Parts............................................ 28

Accessories ....................................................... 28

Parts Central...................................................... 29

Parts .................................................................. 30

Warranty ..............................................Back Cover

www.desatech.com

123167-01D 3

WARNING: This product

contains and/or generates

chemicals known to the State

of California to cause cancer or

birth defects or other reproduc-

tive harm.

IMPORTANT: Read this owner’s

manual carefully and completely

before trying to assemble, op-

erate or service this replace.

Improper use of this replace

can cause serious injury or

death from burns, re, explo-

sion, electrical shock and carbon

monoxide poisoning.

DANGER: Carbon monoxide

poisoning may lead to death!

Carbon Monoxide Poisoning: Early signs

of carbon monoxide poisoning resemble the

u, with headaches, dizziness or nausea. If

you have these signs, the replace may not

be working properly. Get fresh air at once!

Have replace serviced. Some people are

more affected by carbon monoxide than oth-

ers. These include pregnant women, people

with heart or lung disease or anemia, those

under the inuence of alcohol and those at

high altitudes.

Natural and Propane/LP Gas: Natural and

propane/LP gases are odorless. An odor-

making agent is added to these gases. The

odor helps you detect a gas leak. However,

the odor added to the gas can fade. Gas may

be present even though no odor exists.

Make certain you read and understand all

warnings. Keep this manual for reference. It

is your guide to safe and proper operation of

this replace.

WARNING: Any change to

this heater or its controls can

be dangerous.

SAFETY

Continued

WARNING: Do not use a

blower insert, heat exchanger

insert or other accessory not ap-

proved for use with this heater.

WARNING: Do not allow fans

to blow directly into the replace.

Avoid any drafts that alter burner

ame patterns. Ceiling fans can

create drafts that alter burner

ame patterns. Altered burner

patterns can cause sooting.

Due to high temperatures, the

appliance should be located out

of trafc and away from furniture

and draperies.

Do not place clothing or other

ammable material on or near

the appliance. Never place any

objects on the heater.

Heater base assembly becomes

very hot when running heater.

Keep children and adults away

from hot surface to avoid burns

or clothing ignition. Heater

will remain hot for a time after

shutdown. Allow surface to cool

before touching.

Carefully supervise young chil-

dren when they are in the room

with heater.

You must operate this heater

with a replace screen in place.

Make sure replace screen is

closed before running heater.

Keep the appliance area clear

and free from combustible ma-

terials, gasoline and other am-

mable vapors and liquids.

www.desatech.com 123167-01D4

SAFETY

Continued

1. This appliance is only for use with the type

of gas indicated on the rating plate. This

appliance is not convertible for use with

other gases.

2. Do not place propane/LP supply tank(s)

inside any structure. Locate propane/LP

supply tank(s) outdoors (propane/LP units

only).

3. To prevent performance problems, the use

of a propane/LP tank of less than 100 lbs.

capacity is not recommended (propane/

LP units only).

4. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not

use any phone in your building

• immediately call your gas supplier from

a neighbor’s phone. Follow the gas sup-

plier’s instructions

• if you cannot reach your gas supplier,

call the re department

5. This heater shall not be installed in a

bedroom or bathroom.

6. Do not burn solid-fuel in a masonry or

UL127 factory-built replace in which a

vent-free room heater is installed.

7. Before installing in a solid fuel burning re-

place, the chimney ue and rebox must

be cleaned of soot, creosote, ashes and

loose paint by a qualied chimney cleaner.

Creosote will ignite if highly heated. A dirty

chimney ue may create and distribute

soot within the house. Inspect chimney

ue and rebox for damage. If damaged,

repair ue before operating heater.

8. If replace has glass doors, never operate

this heater with glass doors closed. If you

operate heater with doors closed, heat

buildup inside replace will cause glass to

burst. Make sure there are no obstructions

across openings of replace.

9. This log heater is designed to be smoke-

less. If logs ever appear to smoke, turn off

heater and call a qualied service person.

Note: During initial operation, slight smok-

ing could occur due to log curing and

heater burning manufacturing residues.

10. To prevent the creation of soot, follow the

instructions in Cleaning and Maintenance,

page 22.

11. Before using furniture polish, wax, carpet

cleaner or similar products, turn heater off. If

heated, the vapors from these products may

create a white powder residue within burner

box or on adjacent walls or furniture.

12. This heater needs fresh, outside air ven-

tilation to run properly. This heater has an

Oxygen Depletion Sensing (ODS) safety

shutoff system. The ODS shuts down the

heater if not enough fresh air is available.

See Air for Combustion and Ventilation,

page 6. If heater keeps shutting off, see

Troubleshooting, page 24.

13. Do not run heater

• where ammable liquids or vapors are

used or stored

• under dusty conditions

14. Do not use this heater to cook food or burn

paper or other objects.

15. Do not use heater if any part has been ex-

posed to or under water. Immediately call

a qualied service technician to inspect

the room heater and to replace any part

of the control system and any gas control

which has been under water.

16. Do not operate heater if any log is broken.

Do not operate heater if a log is chipped

(dime-sized or larger).

17. Turn heater off and let cool before servic-

ing. Only a qualied service person should

service and repair heater.

18. Operating heater above elevations of

4,500 feet could cause pilot outage.

19. Provide adequate clearances around air

openings.

20. Solid fuels shall not be burned in a re-

place where a decorative appliance is

installed.

21. Installation and the provisions for com-

bustion and ventilation air must conform

with the National Fuel Gas Code, ANSI

Z223.1/NFPA 54.

22. When installing as a vented appliance in a

manufactured home or mobile home, the

installation must conform with the Manu-

factured Home Construction and Safety

Standard, Title 24 CFR, Part 3280.

www.desatech.com

123167-01D 5

Figure 1 - Yellow Flame Vent-Free Gas Log Heater

LOCAL CODES

UNPACKING

PRODUCT IDENTIFICATION

Control Knob

Log Set

Install and use heater with care. Follow all

local codes. In the absence of local codes,

use the latest edition of The National Fuel

Gas Code ANSI Z223/NFPA 54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

Note: Where listed vented decorative logs

are required, thermostat models are not

permitted.

State of Massachusetts: The installa-

tion must be made by a licensed plumber

or gas fitter in the Commonwealth of

Massachusetts.

Sellers of unvented propane or natural

gas-red supplemental room heaters shall

provide to each purchaser a copy of 527

CMR 30 upon sale of the unit.

Vent-free gas products are prohibited for

bedroom and bathroom installation in the

Commonwealth of Massachusetts.

CAUTION: Do not remove the

data plates from the grate as-

sembly. The data plates contain

important warranty and safety

information.

1. Remove logs and heater base assembly

from carton.

Note: Do not pick up heater base assem-

bly by burners. This could damage heater.

Always handle base assembly by grate.

2. Remove all protective packaging applied

to logs and heater for shipment.

3. Check heater for any shipping damage. If

heater is damaged call DESA Heating, LLC

at 1-866-672-6040 for replacement parts

before returning to dealer.

PRODUCT FEATURES

OpERATION

This heater is clean burning. It requires no

outside venting. There is no heat loss out a

vent or up a chimney. Heat is generated by

realistic, dancing yellow ames. This heater

is designed for vent-free operation with ue

damper closed. It has been tested and ap-

proved to ANSI Z21.11.2 standard for un-

vented heaters. State and local codes in some

areas prohibit the use of vent-free heaters.

SAFETY pILOT

This heater has a pilot with an Oxygen Deple-

tion Sensing (ODS) safety shutoff system. The

ODS/pilot is a required feature for vent-free

room heaters. The ODS/pilot shuts off the

heater if there is not enough fresh air.

Millivolt Valve

Battery Pack

www.desatech.com 123167-01D6

AIR FOR COMBUSTION AND VENTILATION

WARNING: This heater shall

not be installed in a room or space

unless the required volume of in-

door combustion air is provided

by the method described in the

National Fuel Gas Code, ANSI

Z223.1/NFPA 54, the International

Fuel Gas Code, or applicable lo-

cal codes. Read the following in-

structions to insure proper fresh

air for this and other fuel-burning

appliances in your home.

Today’s homes are built more energy efcient

than ever. New materials, increased insulation

and new construction methods help reduce

heat loss in homes. Home owners weather

strip and caulk around windows and doors

to keep the cold air out and the warm air in.

During heating months, home owners want

their homes as airtight as possible.

While it is good to make your home energy

efcient, your home needs to breathe. Fresh

air must enter your home. All fuel-burning ap-

pliances need fresh air for proper combustion

and ventilation.

Exhaust fans, replaces, clothes dryers and

fuel burning appliances draw air from the house

to operate. You must provide adequate fresh

air for these appliances. This will insure proper

venting of vented fuel-burning appliances.

pROVIDING ADEQUATE

VENTILATION

The following are excerpts from National Fuel

Gas Code. ANSI Z223.1/NFPA 54, Air for

Combustion and Ventilation.

All spaces in homes fall into one of the three

following ventilation classications:

1. Unusually Tight Construction

2. Unconned Space

3. Conned Space

The information on pages 6 through 8 will help

you classify your space and provide adequate

ventilation.

Unusually Tight Construction

The air that leaks around doors and windows

may provide enough fresh air for combustion

and ventilation. However, in buildings of un-

usually tight construction, you must provide

additional fresh air.

Unusually tight construction is dened as

construction where:

a. walls and ceilings exposed to the out-

side atmosphere have a continuous

water vapor retarder with a rating of

one perm (6x10-11 kg per pa-sec-m2) or

less with openings gasketed or sealed

and

b. weather stripping has been added on

openable windows and doors and

c. caulking or sealants are applied to

areas such as joints around window

and door frames, between sole plates

and oors, between wall-ceiling joints,

between wall panels, at penetrations

for plumbing, electrical and gas lines

and at other openings.

If your home meets all of the three criteria

above, you must provide additional fresh air.

See Ventilation Air From Outdoors, page 8.

If your home does not meet all of the three

criteria above, proceed to Determining

Fresh-Air Flow For Heater Location.

Conned Space and Unconned Space

The National Fuel Gas Code ANSI Z223.1/

NFPA 54 denes a conned space as a space

whose volume is less than 50 cubic feet per

1,000 Btu/hr (4.8 m3 per kw) of the aggregate

input rating of all appliances installed in that

space and an unconned space as a space

whose volume is not less than 50 cubic feet

per 1,000 Btu/hr (4.8 m3 per kw) of the ag-

gregate input rating of all appliances installed

in that space. Rooms communicating directly

with the space in which the appliances are

installed*, through openings not furnished

with doors, are considered a part of the un-

conned space.

* Adjoining rooms are communicating only if

there are doorless passageways or ventilation

grills between them.

DETERMINING FRESH-AIR FLOW

FOR FIREpLACE LOCATION

Determining if You Have a Conned or

Unconned Space

Use this work sheet to determine if you have

a conned or unconned space.

Space: Includes the room in which you will

install replace plus any adjoining rooms with

doorless passageways or ventilation grills

between the rooms.

www.desatech.com

123167-01D 7

1. Determine the volume of the space (length

x width x height).

Length x Width x Height =__________cu. ft.

(volume of space)

Example: Space size 20 ft. (length) x 16 ft.

(width) x 8 ft. (ceiling height) = 2,560 cu. ft.

(volume of space)

If additional ventilation to adjoining room

is supplied with grills or openings, add the

volume of these rooms to the total volume

of the space.

2. Multiply the space volume by 20 to determine

the maximum Btu/Hr the space can support.

________ (volume of space) x 20 = (Maxi-

mum Btu/Hr the space can support)

Example: 2,560 cu. ft. (volume of space) x

20 = 51,200 (maximum Btu/Hr the space can

support)

3. Add the Btu/Hr of all fuel burning appliances

in the space.

Vent-free replace __________ Btu/Hr

Gas water heater* __________ Btu/Hr

Gas furnace __________ Btu/Hr

Vented gas heater __________ Btu/Hr

Gas replace logs __________ Btu/Hr

Other gas appliances* + __________ Btu/Hr

Total = __________ Btu/Hr

* Do not include direct-vent gas appliances.

Direct-vent draws combustion air from the

outdoors and vents to the outdoors.

Example:

Gas water heater __________ Btu/Hr

Vent-free replace + __________ Btu/Hr

Total = __________ Btu/Hr

4. Compare the maximum Btu/Hr the space

can support with the actual amount of Btu/

Hr used.

_______

Btu/Hr (maximum the space can

support)

_______ Btu/Hr (actual amount of Btu/Hr

used)

Example: 51,200 Btu/Hr (maximum the

space can support)

71,500 Btu/Hr (actual amount of

Btu/Hr used)

The space in the example is a conned space

because the actual Btu/Hr used is more than the

maximum Btu/Hr the space can support. You

must provide additional fresh air. Your options

are as follows:

A. Rework worksheet, adding the space of an

adjoining room. If the extra space provides an

unconned space, remove door to adjoining

40,000

31,500

71,500

AIR FOR COMBUSTION AND VENTILATION

Continued

Figure 2 - Ventilation Air from Inside Building

Remove

Door into

Adjoining

Room,

Option

Ve ntilation Grills

Into Adjoining Room,

Option 2

Ve ntilation

Grills Into

Adjoining

Room,

Option 1

12"

room or add ventilation grills between rooms.

See Ventilation Air From Inside Building.

B. Vent room directly to the outdoors. See

Ventilation Air From Outdoors, page 8.

C. Install a lower Btu/Hr replace, if lower Btu/

Hr size makes room unconned.

If the actual Btu/Hr used is less than the maxi-

mum Btu/Hr the space can support, the space is

an unconned space. You will need no additional

fresh air ventilation.

WARNING:Ifthearea inwhich

the heater may be operated does

not meet the required volume for

indoor combustion air, combus-

tion and ventilation air shall be

provided by one of the methods

described in the National Fuel

Gas Code,ANSI Z223.1/NFPA 54,

the International Fuel Gas Code,

or applicable local codes.

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining

unconned space. When ventilating to an

adjoining unconned space, you must provide

two permanent openings: one within 12" of the

ceiling and one within 12" of the oor on the

wall connecting the two spaces (see options

1 and 2, Figure 2). You can also remove door

into adjoining room (see option 3, Figure 2).

Follow the National Fuel Gas Code ANSI

Z223.1/NFPA 54 Air for Combustion and

Ventilation for required size of ventilation

grills or ducts.

www.desatech.com 123167-01D8

INSTALLATION

NOTICE: This heater is intended

for use as supplemental heat.

Use this heater along with your

primary heating system. Do not

install this heater as your pri-

mary heat source. If you have a

central heating system, you may

run system’s circulating blower

while using heater. This will help

circulate the heat throughout the

house. In the event of a power

outage, you can use this heater

as your primary heat source.

Figure 3 - Ventilation Air from Outdoors

Outlet

Air

V e ntilated

Attic

Outlet

Inlet

Air

Inlet Air V e ntilated

Crawl Space

T o

Crawl

Space

T o Attic

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation

grills or ducts. You must provide two perma-

nent openings: one within 12" of the ceiling

and one within 12" of the oor. Connect these

items directly to the outdoors or spaces open

to the outdoors. These spaces include attics

and crawl spaces. Follow the National Fuel

Gas Code ANSI Z223.1/NFPA 54, Air for

Combustion and Ventilation for required size

of ventilation grills or ducts.

IMPORTANT: Do not provide openings for

inlet or outlet air into attic if attic has a thermo-

stat-controlled power vent. Heated air entering

the attic will activate the power vent.

AIR FOR COMBUSTION

AND VENTILATION

Continued

WARNING: A qualied ser-

vice person must install heater.

Follow all local codes.

NOTICE: State or local codes

may only allow operation of this

appliance in a vented congura-

tion. Check your state or local

codes.

WARNING: Before installing

in a solid fuel burning replace,

the chimney ue and rebox

must be cleaned of soot, creo-

sote, ashes and loose paint by

a qualified chimney cleaner.

Creosote will ignite if highly

heated. A dirty chimney ue may

create and distribute soot within

the house. Inspect chimney ue

and rebox for damage. If dam-

aged, repair ue before operat-

ing heater.

WARNING: Seal any fresh

air vents or ash clean-out doors

located on oor or wall of re-

place. If not, drafting may cause

pilot outage or sooting. Use a

heat-resistant sealant. Do not

seal chimney ue damper.

WARNING: Never install the

heater

• in a bedroom or bathroom

• in a recreational vehicle

• where curtains, furniture,

clothing or other ammable

objects are less than 36" from

front or 42" from top of heater.

For side clearances see Figure

4, page 9

• in high trafc areas

• in windy or drafty areas

www.desatech.com

123167-01D 9

LOG SIZING REQUIREMENTS

Minimum Firebox Size

Height Depth Front

Width

Rear

Width*

17" 13" 28" 20.5"

CAUTION: This heater cre-

ates warm air currents. These

currents move heat to wall sur-

faces next to heater. Installing

heater next to vinyl or cloth wall

coverings or operating heater

where impurities (such as, but

not limited to, tobacco smoke,

aromatic candles, cleaning u-

ids, oil or kerosene lamps, etc.) in

the air exist, may discolor walls

or cause odors.

IMPORTANT:Vent-free heaters add moisture to

the air. Although this is benecial, installing heater

in rooms without enough ventilation air may cause

mildew to form from too much moisture. See Air

for Combustion and Ventilation, page 6.

CHECK GAS TYpE

Use only the correct gas type (natural or pro-

pane/LP) for your unit. If your gas supply is not

correct, do not install heater. Call dealer where

you bought heater for proper type heater.

WARNING: This appliance is

equipped for either natural gas

or propane/LP gas but not both.

Gas type is indicated on the rat-

ing plate. Field conversion is not

permitted.

INSTALLATION AND CLEARANCES

(Vent-Free Operation Only)

WARNING: Maintain the

minimum clearances. If you can,

provide greater clearances from

oor, ceiling and adjoining wall.

MINIMUM FIREpLACE CLEARANCE

TO COMBUSTIBLE MATERIALS

Side Wall 16", Ceiling 42", Front 36"

*Measured at 13" Depth

Carefully follow the instructions below. This

will ensure safe installation into a masonry,

UL127-listed manufactured replace or certi-

ed vent-free rebox.

MINIMUM CLEARANCES FOR SIDE

COMBUSTIBLE MATERIAL, SIDE WALL

AND CEILING

A. Clearances from the side of the replace

cabinet to any combustible material and

wall should follow diagram in Figure 4.

Example: The face of a mantel, bookshelf,

etc. is made of combustible material and

protrudes 3 1/2" from the wall. This com-

bustible material must be 4" from the side

of the replace cabinet (see Figure 4).

Note: When installing your gas logs into

a manufactured rebox, follow rebox

manufacturer’s instructions for minimum

clearances to combustible materials.

B. Clearances from the top of the replace

opening to the ceiling should not be less

than 42".

NOTICE: Manual control heaters

may be used as a vented product.

If so, you must always run heater

with chimney ue damper open.

If running heater with damper

open, noncombustible material

above replace opening is not

needed. Go to Installing Damper

Clamp Accessory for Vented

Operation, page 11.

Figure 4 - Minimum Clearance for

Combustible to Wall

*Minimum 16" from Side Wall

Example

INSTALLATION

Continued

www.desatech.com 123167-01D10

Minimum

Noncombustible

Material

Minimum

Noncombustible

Material Height

Distances to

Underside of

Mantel

To p of

Fireplace

Opening

Underside

of Mantel

Shelf

Mantel Shelf

12"

(A)

18" 20" 22" 24"

All

minimum

distances

are in

inches

10"

INSTALLATION

Continued

If Using Mantel

You must have noncombustible material(s)

above the replace opening. Noncombustible

materials (such as slate, marble, tile, etc.) must

be at least 1/2" thick. With sheet metal, you

must have noncombustible material behind

it. Noncombustible material must extend at

least 12" up. See Figures 5 and 6 for minimum

clearances.

MANTEL CLEARANCES

In addition to meeting noncombustible mate-

rial clearances, you must also meet required

clearances between replace opening and

mantel shelf. If you do not meet the clearances

listed below, you will need a hood.

Determining Minimum Mantel Clearance

If you meet minimum clearance between

mantel shelf and top of replace opening, a

hood is not required (see Figure 6).

NOTICE: Surface temperatures

of adjacent walls and mantels be-

come hot during operation. Walls

and mantels above the rebox

may become hot to the touch.

If installed properly, these tem-

peratures meet the requirement

of the national product standard.

Follow all minimum clearances

shown in this manual.

Figure 6 - Minimum Mantel Clearances

Without Using Hood

MINIMUM NONCOMBUSTIBLE

MATERIAL CLEARANCES

If Not Using Mantel

Note: If using a mantel, proceed to If Using

Mantel. If not using a mantel, follow the infor-

mation below.

You must have noncombustible material(s)

above the replace opening. Noncombustible

materials (such as slate, marble, tile, etc.)

must be at least 1/2" thick. With sheet metal,

you must have noncombustible material be-

hind it. Noncombustible material must extend

at least 12" up (for all models). See Figure 5

for minimum clearances.

Heat Resistant

Material

(A)

Figure 5 - Heat Resistant Material (Slate,

Marble, Tile, etc.) Above Fireplace

Noncombustible

Material Distance (A)

Requirements for Safe

Installation

12" or more Noncombustible mate-

rial OK.

Between 8"

and 12"

24" Models: Install

fireplace hood acces-

sory (GA6050, GA6052,

GA6053, see Accesso-

ries, page 27).

18" Model: Noncombus-

tible material OK.

Less than 8" Noncombustible material

must be extended to at

least 8". See Between

8" and 12", above. If you

cannot extend material,

you must operate heater

with ue damper open and

damper clamp installed.

This manual suits for next models

Table of contents

Other Desa Gas Heater manuals

Desa

Desa VF-30N-PJD Quick start guide

Desa

Desa LDL3924NR Quick start guide

Desa

Desa CHL3924NR Quick start guide

Desa

Desa Comfort Glow CGN12 Quick start guide

Desa

Desa REM10PT Quick start guide

Desa

Desa Vanguard VN2000BTC Quick start guide

Desa

Desa Comfort Glow CGP11A Quick start guide

Desa

Desa Glo-Warm FB-2B Quick start guide

Desa

Desa NY100 Original instructions

Desa

Desa Comfort Glow CGP10L Quick start guide

Desa

Desa NY108 Original instructions

Desa

Desa RH10PT Quick start guide

Desa

Desa FLAME-MAX FVFM27NR Quick start guide

Desa

Desa VUL24ND Quick start guide

Desa

Desa CHL3924PR Quick start guide

Desa

Desa Vanguard VN600BA Original instructions

Desa

Desa 30 Quick start guide

Desa

Desa VN1000BTA Quick start guide

Desa

Desa Design Dynamics HCA-18-RFN Quick start guide

Desa

Desa Medallion MR10NT Quick start guide

Desa

Desa Comfort Glow CCL3018NA Quick start guide

Desa

Desa VN18B Original instructions

Desa

Desa RCLP155B User manual

Desa

Desa Comfort Glow CGR35PA Quick start guide

Popular Gas Heater manuals by other brands

Superior

Superior BGE18NV Installation and operation instructions

Dru

Dru Room-sealed atmospheric gas-fired heating... user manual

klover

klover TKR 35 user guide

Rothenberger Industrial

Rothenberger Industrial 035984 instruction manual

New Buck Corporation

New Buck Corporation 34 user manual

Hargrove

Hargrove Timberland Glow Operation and installation guide

Kinder

Kinder Cameo BF Installation and maintenance instructions

Qlima

Qlima GH 438 B-2 Directions for use

Gasmate

Gasmate AH100 Series instructions

Medallion

Medallion MBP20TLB OWNER'S OPERATION AND INSTALLATION MANUAL

Clarke

Clarke DEVIL 910SS User instructions

Superior

Superior BGE18NR Operation instructions

Brant Radiant Heaters

Brant Radiant Heaters QTD Series User instruction

L.B. White

L.B. White Therma Grow HW220 Owner's manual and instructions

Sealey

Sealey LP35.V5 instructions

Italkero

Italkero Falo Evo User manual and assembly instructions

Williams

Williams 2509822A owner's manual

Romotop

Romotop Heckla 1301 Installation, operator and maintenance manual