Desa CDR3924NT Quick start guide

For more information, visit www.desatech.com

WARNING: If the information in this manual is not fol-

lowed exactly, a re or explosion may result causing

property damage, personal injury or loss of life.

— Do not store or use gasoline or other ammable

vapors and liquids in the vicinity of this or any other

appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re

department.

— Installation and service must be performed by a quali-

ed installer, service agency or the gas supplier.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

UNVENTED (VENT-FREE) GAS LOG HEATER

OWNER’S OPERATION AND INSTALLATION MANUAL

24" THERMOSTAT MODELS CDR3924NT AND CDR3924PT

www.desatech.com 113183-01F2

SAFETy INFORMATION

TAbLE OF CONTENTS

Safety Information ............................................... 2

Local Codes......................................................... 4

Product Identication........................................... 5

Unpacking............................................................ 5

Product Features................................................. 5

Air For Combustion and Ventilation..................... 5

Installation ........................................................... 8

Operating Heater............................................... 16

Inspecting Burners............................................. 18

Technical Service............................................... 18

Cleaning and Maintenance................................ 19

Troubleshooting................................................. 20

Optional Positioning of Thermostat Sensing Bulb....24

Specications .................................................... 25

Replacement Parts............................................ 25

Service Hints ..................................................... 25

Accessories ....................................................... 25

Illustrated Parts Breakdown and Parts List........ 26

Warranty Information ...........................Back Cover

WARNING: Improper in-

stallation, adjustment, al-

teration, service or mainte-

nance can cause injury or

property damage. Refer to

this manual for correct in-

stallation and operational

procedures. For assis-

tance or additional infor-

mation consult a qualied

installer, service agency or

the gas supplier.

WARNING: This appliance

is for installation only in a

solid-fuel burning masonry

or UL127 factory-built re-

place or in an listed vent-

less rebox enclosure. It is

design-certied for these

installations in accordance

with ANSI Z21.11.2. Excep-

tion: Do not install this

appliance in a factory-built

replace that includes in-

structions stating it has not

been tested or should not

be used with unvented gas

logs. For unmarked facto-

ry-built replaces, contact

replace manufacturer if

unsure of this application.

WARNING: This is an

unvented gas-red heat-

er. It uses air (oxygen)

from the room in which

it is installed. Provisions

for adequate combustion

and ventilation air must

be provided. Refer to Air

for Combustion and Ven-

tilation section on page 5

of this manual.

This appliance may be in-

stalled in an aftermarket,*

permanently located,

manufactured (mobile)

home, where not prohib-

ited by local codes.

This appliance is only for

use with the type of gas

indicated on the rating

plate. This appliance is

not convertible for use

with other gases.

* Aftermarket: Completion of sale, not for

purpose of resale, from the manufacturer

www.desatech.com 3113183-01F

WARNING: This product

contains and/or generates

chemicals known to the State

of California to cause cancer or

birth defects or other reproduc-

tive harm.

IMPORTANT: Read this owner’s

manual carefully and completely

before trying to assemble, oper-

ate or service this heater. Improp-

er use of this heater can cause

property damage and serious

injury or death from burns, re,

explosion, electrical shock and

carbon monoxide poisoning.

DANGER: Carbon monoxide

poisoning may lead to death!

Carbon Monoxide Poisoning: Early signs of carbon

monoxide poisoning resemble the u, with head-

aches, dizziness or nausea. If you have these signs,

the heater may not be working properly. Get fresh

air at once! Have heater serviced. Some people

are more affected by carbon monoxide than others.

These include pregnant women, people with heart

or lung disease or anemia, those under the inuence

of alcohol and those at high altitudes.

Natural and Propane/LP Gas: Natural and pro-

pane/LP gases are odorless. An odor-making agent

is added to the gas. The odor helps you detect a gas

leak. However, the odor added to the gas can fade.

Gas may be present even though no odor exists.

Make certain you read and understand all warn-

ings. Keep this manual for reference. It is your

guide to safe and proper operation of this heater.

WARNING: Any change to

this heater or its controls can

be dangerous.

WARNING: Do not use a

blower insert, heat exchanger

insert or other accessory not ap-

proved for use with this heater.

SAFETy INFORMATION

Continued WARNING: This appliance

is for installation only in a

solid-fuel burning replace or

approved ventless rebox en-

closure.

WARNING: Do not allow fans

to blow directly into the replace.

Avoid any drafts that alter burner

ame patterns. Ceiling fans can

create drafts that alter burner

ame patterns. Altered burner

patterns can cause sooting.

Due to high temperatures, the

appliance should be located out

of trafc and away from furniture

and draperies.

Do not place clothing or other

ammable material on or near

the appliance. Never place any

objects on the heater.

Heater base assembly becomes

very hot when running heater.

Keep children and adults away

from hot surface to avoid burns

or clothing ignition. Heater

will remain hot for a time after

shutdown. Allow surface to cool

before touching.

Carefully supervise young chil-

dren when they are in the room

with heater.

You must operate this heater

with a replace screen in place.

Make sure replace screen is

closed before running heater.

Keep the appliance area clear

and free from combustible ma-

terials, gasoline and other am-

mable vapors and liquids.

www.desatech.com 113183-01F4

This appliance is only for use with the type of

gas indicated on the rating plate. This appliance

is not convertible for use with other gases.

2. Do not place propane/LP supply tank(s) in-

side any structure. Locate propane/LP supply

tank(s) outdoors.

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not use

any phone in your building

• immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions

• if you cannot reach your gas supplier, call

the re department

This heater shall not be installed in a bedroom or

bathroom, unless installed as a vented appliance.

Before installing in a solid fuel burning re-

place, the chimney ue and rebox must be

cleaned of soot, creosote, ashes and loose paint

by a qualied chimney cleaner. Creosote will

ignite if highly heated. A dirty chimney ue

may create and distribute soot within the house.

Inspect chimney ue and rebox for damage. If

damaged, repair ue before operating heater.

6. Do not burn solid-fuel in a masonry or UL127

factory-built replace in which a vent-free

room heater is installed.

If replace has glass doors, never operate this

heater with glass doors closed. If you operate

heater with doors closed, heat buildup inside

replace will cause glass to burst. Make sure there

are no obstructions across openings of replace.

8. To prevent the creation of soot, follow the

instructions in Cleaning and Maintenance,

page 19.

9. Before using furniture polish, wax, carpet

cleaner or similar products, turn heater off. If

heated, the vapors from these products may

create a white powder residue within burner

box or on adjacent walls and furniture.

10. This heater needs fresh, outside air ventilation to

run properly. This heater has an Oxygen Deple-

tion Sensing (ODS) safety shutoff system. The

ODS shuts down the heater if enough fresh air

is not available. See Air for Combustion and

Ventilation, page 5. If heater keeps shutting off,

see Troubleshooting, page 20.

SAFETy INFORMATION

Continued

11. Do not run heater

• where ammable liquids or vapors are used

or stored

• under dusty conditions

12. Do not use this heater to cook food or burn

paper or any other type of solid fuels.

13. Do not use heater if any part has been exposed

to or under water. Immediately call a qualied

service technician to inspect the room heater

and to replace any part of the control system and

any gas control which has been under water.

14. Do not operate heater if any log is broken. Do

not operate heater if a log is chipped (dime-

sized or larger).

15. Turn heater off and let cool before servicing,

installing or repairing. Only a qualied ser-

vice person should install, service or repair

heater.

16. Operating heater above elevations of 4,500

feet may cause pilot outage.

17. To prevent performance problems with pro-

pane/LP models, do not use propane/LP fuel

tank of less than 100 lb. capacity.

18. Provide adequate clearances around air

openings.

LOCAL CODES

Install and use heater with care. Follow all local

codes. In the absence of local codes, use the lat-

est edition of The National Fuel Gas Code ANSI

Z223.1/NFPA 54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

Note: Where listed vented decorative logs are

required, thermostat operation is not permitted.

State of Massachusetts: The installa-

tion must be made by a licensed plumber

or gas fitter in the Commonwealth of

Massachusetts.

Sellers of unvented propane or natural

gas-red supplemental room heaters shall

provide to each purchaser a copy of 527

CMR 30 upon sale of the unit.

Vent-free gas products are prohibited for

bedroom and bathroom installation in the

Commonwealth of Massachusetts.

www.desatech.com 5113183-01F

PRODUCT

IDENTIFICATION

Log Set

Base

Assembly

Ignitor

Burner

Control Knob

Figure 1 - Product Identication

Grate

UNPACkING

CAUTION: Do not remove

the data plates from the base as-

sembly. The data plates contain

important warranty and safety

information.

1. Remove logs and heater base assembly from

carton. Note: Do not pick up heater base as-

sembly by burners. This could damage heater.

Always handle base assembly by the sides of

assembly.

2. Remove all protective packaging applied to

logs and heater for shipment.

3. Check all items for any shipping damage. If

damaged, promptly inform dealer where you

bought heater.

PRODUCT FEATURES

OPERATION

This heater is clean burning. It requires no outside

venting. There is no heat loss out a vent or up a

chimney. Heat is generated by both realistic ames

and glowing coals. This heater is designed for vent-

free operation with ue damper closed. It has been

tested and approved to ANSI Z21.11.2 standard for

unvented heaters. State and local codes in some

areas prohibit the use of vent-free heaters.

SAFETY DEVICE

This heater has a pilot with an Oxygen Deple-

tion Sensing (ODS) safety shutoff system. The

ODS/pilot is a required feature for vent-free room

heaters. The ODS/pilot shuts off the heater if there

is not enough fresh air.

IGNITION SYSTEM

This heater has an electronic ignitor to light heater

fuel supply.

AIR FOR COMbUSTION

AND VENTILATION

WARNING: This heater shall

not be installed in a conned

space or unusually tight construc-

tion unless provisions are provid-

ed for adequate combustion and

ventilation air. Read the following

instructions to insure proper fresh

air for this and other fuel-burning

appliances in your home.

Today’s homes are built more energy efcient

than ever. New materials, increased insulation and

new construction methods help reduce heat loss

in homes. Home owners weather strip and caulk

around windows and doors to keep the cold air out

and the warm air in. During heating months, home

owners want their homes as airtight as possible.

While it is good to make your home energy ef-

cient, your home needs to breathe. Fresh air must

enter your home. All fuel-burning appliances need

fresh air for proper combustion and ventilation.

Exhaust fans, replaces, clothes dryers and fuel

burning appliances draw air from the house to

operate. You must provide adequate fresh air for

these appliances. This will insure proper venting

of vented fuel-burning appliances.

PROVIDING ADEQUATE

VENTILATION

The following are excerpts from National Fuel

Gas Code, ANSI Z223.1/NFPA 54, Section 5.3,

Air for Combustion and Ventilation.

All spaces in homes fall into one of the three fol-

lowing ventilation classications:

1. Unusually Tight Construction

2. Unconned Space

3. Conned Space

The information on pages 5 through 7 will help

you classify your space and provide adequate

ventilation.

www.desatech.com 113183-01F6

Unusually Tight Construction

The air that leaks around doors and windows

may provide enough fresh air for combustion and

ventilation. However, in buildings of unusually

tight construction, you must provide additional

fresh air.

Unusually tight construction is dened as

construction where:

a. walls and ceilings exposed to the out-

side atmosphere have a continuous

water vapor retarder with a rating of

one perm (6 x 10-11 kg per pa-sec-m2) or

less with openings gasketed or sealed

and

b. weather stripping has been added on

openable windows and doors and

c. caulking or sealants are applied to

areas such as joints around window

and door frames, between sole plates

and oors, between wall-ceiling joints,

between wall panels, at penetrations

for plumbing, electrical and gas lines

and at other openings.

If your home meets all of these three cri-

teria, you must provide additional fresh

air. See Ventilation Air From Outdoors,

page 7.

If your home does not meet all of the three

criteria above, proceed to Determining

Fresh-Air Flow For Heater Location.

Conned and Unconned Space

The National Fuel Gas Code, ANSI Z223.1/NFPA 54

denes a conned space as a space whose volume

is less than 50 cubic feet per 1,000 Btu per hour

(4.8 m3 per kw) of the aggregate input rating of all

appliances installed in that space and an unconned

space as a space whose volume is not less than 50

cubic feet per 1,000 Btu/Hr (4.8 m3 per kw) of the

aggregate input rating of all appliances installed in

that space. Rooms communicating directly with the

space in which the appliances are installed*, through

openings not furnished with doors, are considered

a part of the unconned space.

* Adjoining rooms are communicating only if

there are doorless passageways or ventilation grills

between them.

DETERMINING FRESH-AIR FLOW

FOR HEATER LOCATION

Determining if You Have a Conned or

Unconned Space

Use this work sheet to determine if you have a

conned or unconned space.

Space: Includes the room in which you will install

heater plus any adjoining rooms with doorless pas-

sageways or ventilation grills between the rooms.

1. Determine the volume of the space (length x

width x height).

Length x Width x Height =__________cu. ft.

(volume of space)

Example: Space size 20 ft. (length) x 16 ft.

(width) x 8 ft. (ceiling height) = 2560 cu. ft.

(volume of space)

If additional ventilation to adjoining room is

supplied with grills or openings, add the volume

of these rooms to the total volume of the space.

2. Multiply the space volume by 20 to determine

the maximum Btu/Hr the space can support.

__________ (volume of space) x 20 = (Maxi-

mum Btu/Hr the space can support)

Example: 2560 cu. ft. (volume of space) x 20 =

51,200 (maximum Btu/Hr the space can support)

3. Add the Btu/Hr of all fuel burning appliances in

the space.

Vent-free heater ___________ Btu/Hr

Gas water heater* ___________ Btu/Hr

Gas furnace ___________ Btu/Hr

Vented gas heater ___________ Btu/Hr

Gas replace logs ___________ Btu/Hr

Gas water heater __________ Btu/Hr

Other gas appliances* +__________ Btu/Hr

Total = _________ Btu/Hr

* Do not include direct-vent gas appliances. Di-

rect-vent draws combustion air from the outdoors

and vents to the outdoors.

Example:

Gas water heater __________ Btu/Hr

Vent-free heater +__________ Btu/Hr

Total =__________ Btu/Hr

4. Compare the maximum Btu/Hr the space can

support with the actual amount of Btu/Hr used.

_________

Btu/Hr (maximum the space can support)

_________

Btu/Hr (actual amount of Btu/Hr used)

Example: 51,200 Btu/Hr (maximum the space

can support)

79,000 Btu/Hr (actual amount of

Btu/Hr used)

The space in the above example is a conned space

because the actual Btu/Hr used is more than the maxi-

mum Btu/Hr the space can support. You must provide

additional fresh air. Your options are as follows:

AIR FOR COMbUSTION

AND VENTILATION

Continued

40,000

39,000

79,000

www.desatech.com 7113183-01F

A. Rework worksheet, adding the space of an adjoin-

ing room. If the extra space provides an unconned

space, remove door to adjoining room or add

ventilation grills between rooms. See Ventilation

Air From Inside Building.

B. Vent room directly to the outdoors. See Ventila-

tion Air From Outdoors, page 7.

C. Install a lower Btu/Hr heater, if lower Btu/Hr size

makes room unconned.

If the actual Btu/Hr used is less than the maximum

Btu/Hr the space can support, the space is an un-

conned space. You will need no additional fresh

air ventilation.

WARNING: Ifthe area inwhich

the heater may be operated is

smaller than that dened as

an unconned space or if the

building is of unusually tight

construction, provide adequate

combustion and ventilation air

by one of the methods described

in the National Fuel Gas Code,

ANSI Z223.1/NFPA54 Section 5.3

or applicable local codes.

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining un-

conned space. When ventilating to an adjoining

unconned space, you must provide two perma-

nent openings: one within 12" of the ceiling and

one within 12" of the oor on the wall connecting

the two spaces (see options 1 and 2, Figure 2). You

can also remove door into adjoining room (see

option 3, Figure 2). Follow the National Fuel Gas

Code, ANSI Z223.1/NFPA 54, Section 5.3, Air for

Combustion and Ventilation for required size of

ventilation grills or ducts.

AIR FOR COMbUSTION

AND VENTILATION

Continued

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation grills or

ducts. You must provide two permanent openings:

one within 12" of the ceiling and one within 12"

of the oor. Connect these items directly to the

outdoors or spaces open to the outdoors. These

spaces include attics and crawl spaces. Follow the

National Fuel Gas Code, ANSI Z223.1/NFPA 54,

Section 5.3, Air for Combustion and Ventilation for

required size of ventilation grills or ducts.

IMPORTANT: Do not provide openings for inlet

or outlet air into attic if attic has a thermostat-

controlled power vent. Heated air entering the attic

will activate the power vent.

Figure 3 - Ventilation Air from Outdoors

Figure 2 - Ventilation Air from Inside

Building

Outlet

Air

Ventilated

Attic

Outlet

Inlet

Air

Inlet Air Ventilated

Crawl Space

Crawl

Space

To Attic

Remove

Door into

Adjoining

Room,

Option

Ventilation Grills

Into Adjoining Room,

Option 2

Ventilation

Grills Into

Adjoining

Room,

Option 1

12"

www.desatech.com 113183-01F8

INSTALLATION

NOTICE: This heater is intended

for use as supplemental heat.

Use this heater along with your

primary heating system. Do not

install this heater as your pri-

mary heat source. If you have a

central heating system, you may

run system’s circulating blower

while using heater. This will help

circulate the heat throughout the

house. In the event of a power

outage, you can use this heater

as your primary heat source.

WARNING: Installation and

repair should be done by a

qualied service person. The

appliance should be inspected

before use and at least annu-

ally by a professional service

person. More frequent cleaning

may be required due to exces-

sive lint from carpeting, bedding

material, etc. It is imperative that

control compartments, burners

and circulating air passageways

of the appliance be kept clean.

WARNING: Before installing

in a solid fuel burning replace,

the chimney ue and rebox

must be cleaned of soot, creo-

sote, ashes and loose paint by a

qualied chimney cleaner. Creo-

sote will ignite if highly heated. A

dirty chimney ue may create and

distribute soot within the house.

Inspect chimney ue and rebox

for damage. If damaged, repair

ue before operating heater.

WARNING: Seal any fresh

air vents or ash clean-out doors

located on oor or wall of re-

place. If not, drafting may cause

pilot outage or sooting. Use a

heat-resistant sealant. Do not

seal chimney ue damper.

WARNING: Never install the

heater

• in a bedroom or bathroom

• in a recreational vehicle

• where curtains, furniture,

clothing or other ammable

objects are less than 42" from

the front, top or sides of the

rebox opening

• in high trafc areas

• in windy or drafty areas

CAUTION:Thisheatercreates

warm air currents. These currents

move heat to wall surfaces next

to heater. Installing heater next

to vinyl or cloth wall coverings or

operating heater where impurities

(such as, but not limited to, to-

bacco smoke, aromatic candles,

cleaning uids, oil or kerosene

lamps, etc.) in the air exist, may

discolor walls or cause odors.

IMPORTANT: Vent-free heaters add moisture to

the air. Although this is benecial, installing heater

in rooms without enough ventilation air may cause

mildew to form from too much moisture. See Air

for Combustion and Ventilation, page 5.

CHECK GAS TYPE

Use the correct gas type (natural or propane/LP)

for your unit. If your gas supply is not correct, do

not install replace. Call dealer where you bought

replace for proper type replace.

WARNING: This appliance

is equipped for natural or pro-

pane/LP gas. Field conversion

is not permitted.

www.desatech.com 9113183-01F

INSTALLATION AND CLEARANCES

FOR VENT-FREE OPERATION

WARNING: Maintain the

minimum clearances. If possible,

provide greater clearances from

oor, ceiling and adjoining wall.

LOG SIZING REQUIREMENTS

Log Minimum Firebox

Size Height Depth Front Rear *

Width Width

24" 17" 14" 28" 20 1/4"

Minimum Firebox with Blower

24" 17" 14" 34" 22 3/8"

* Measured at 14" depth.

Carefully follow the instructions below. This will

ensure safe installation into a masonry, UL127-listed

manufactured replace or listed vent-free rebox.

Minimum Clearances For Side Combustible

Material, Side Wall and Ceiling

A. Clearances from the side of the fireplace

cabinet to any combustible material and wall

should follow diagram in Figure 4.

Example: The face of a mantel, bookshelf,

etc. is made of combustible material and

protrudes 3 1/2" from the wall. This combus-

tible material must be 4" from the side of the

replace cabinet (see Figure 4).

Note: When installing your gas logs into

a manufactured firebox, follow firebox

manufacturer’s instructions for minimum

clearances to combustible materials.

B. Clearances from the top of the replace opening

to the ceiling should not be less than 42".

INSTALLATION

Continued

Figure 4 - Minimum Clearance for

Combustible to Wall

*Minimum 16" from Side Wall

Example

Figure 5 - Heat Resistant Material (Slate,

Marble, Tile, etc.) Above Fireplace

Minimum Noncombustible Material

Clearances

If Not Using Mantel

Note: If using a mantel proceed to If Using Mantel.

If not using a mantel, follow the information on

this page.

You must have noncombustible material(s) above the

replace opening. Noncombustible materials (such

as slate, marble, tile, etc.) must be at least 1/2" thick.

With sheet metal, you must have noncombustible

material behind it. Noncombustible material must

extend at least 8" up. If noncombustible material is

less than 12", you must install the replace hood ac-

cessory. See Figure 5 for minimum clearances.

If Using Mantel

You must have noncombustible material(s) above

the replace opening. Noncombustible materials

(such as slate, marble, tile, etc.) must be at least

1/2" thick. With sheet metal, you must have non-

combustible material behind it. Noncombustible

material must extend at least 8" up. If noncombus-

tible material is less than 12", you must install the

replace hood accessory. Even if noncombustible

material is more than 12", you may need the hood

accessory to deect heat away from your mantel

shelf. See Figure 5 and Figures 6 and 7, page 10,

for minimum clearances.

IMPORTANT: If you cannot meet these minimum

clearances, you must operate heater with chimney

ue damper open.

Noncombustible Requirements for

Material Distance (A)

Safe Installation

12" or more Noncombustible material

okay.

Between 8" Install replace hood

and 12" accessory (GA6050,

GA6052 or GA6053 see

Accessories, page 25).

Less than 8" Noncombustible material

must be extended to at

least 8". See Between 8"

and 12", above. If you

cannot extend material,

you must operate heater

with ue damper open.

www.desatech.com 113183-01F10

INSTALLATION

Continued

Minimum

Noncombustible

Material

Min.

12" 15" 18" 20"

2½"

10"

12"

Distances to

Underside of

Mantel

Hood

(GA6050,

GA6052 or

GA6053)

Top of

Fireplace

Opening

Underside

of Mantel

Shelf

Mantel Shelf

MANTEL CLEARANCES

In addition to meeting noncombustible material

clearances, you must also meet required clearances

between replace opening and mantel shelf. If

you do not meet the clearances listed below, you

will need a hood.

Determining Minimum Mantel Clearance

If you meet minimum clearance between mantel

shelf and top of replace opening, a hood is not

required (see Figure 6).

Determining Minimum Mantel Clearance

When Using a Hood

If minimum clearances in Figure 6 are not met, you

must have a hood. When using a hood there are

still certain minimum mantel clearances required.

Follow minimum clearances shown in Figure 7

when using hood.

NOTICE: Surface temperatures

of adjacent walls and mantels

become hot during operation.

Walls and mantels above the

firebox may become hot to

the touch. If installed properly,

these temperatures meet the

requirement of the national

product standard. Follow all

minimum clearances shown in

this manual.

NOTICE: If your installation does

not meet the minimum clear-

ances shown, you must do one

of the following:

• operate the logs only with the

ue damper open

• raise the mantel to an accept-

able height

• remove the mantel

FLOOR CLEARANCES

A. If installing appliance on the oor level, you

must maintain the minimum distance of 14"

to combustibles (see Figure 8).

B. If combustible materials are less than 14" to

the replace, you must install appliance at

least 5" above the combustible ooring (see

Figure 9).

Figure 6 - Minimum Mantel Clearances

Without Using Hood

Figure 8 - Minimum Fireplace Clearances

If Installed at Floor Level

Figure 9 - Minimum Fireplace Clearances

Above Combustible Flooring

Figure 7 - Minimum Mantel Clearances

When Using Hood

Minimum Non-

Combustible

Material

Minimum Non-

Combustible

Material Height

Distances to

Underside of

Mantel

Top of Fireplace

Opening

Underside of

Mantel Shelf

12"

(A)

18" 20" 22" 24"

All minimum

distances are

in inches

Log Set

All Models

2 1/2"

10"

14"

Min.

Combustible

Material

Noncombustible Material

Hearth

Min.

Combustible

Material

Other manuals for CDR3924NT

This manual suits for next models

Table of contents

Other Desa Gas Heater manuals

Desa

Desa HDVF3018N Quick start guide

Desa

Desa 30LP User manual

Desa

Desa CCL3018NR Quick start guide

Desa

Desa Comfort Glow CCL3930NTA Quick start guide

Desa

Desa Comfort Glow CGN10TA Quick start guide

Desa

Desa Comfort Glow CGP10TLA Quick start guide

Desa

Desa Comfort Glow CGB3924PR Quick start guide

Desa

Desa Comfort Glow CGN10RL Quick start guide

Desa

Desa Comfort Glow RFN30TA Quick start guide

Desa

Desa ROPANE CONSTRUCTION HEATER User manual

Desa

Desa TC250RNG User manual

Desa

Desa CGN18C Quick start guide

Desa

Desa Comfort Glow CGD3930N Quick start guide

Desa

Desa CFN2800BTB Quick start guide

Desa

Desa R Quick start guide

Desa

Desa VMH3000TPA Quick start guide

Desa

Desa CBT30NT User manual

Desa

Desa DynaVent DNV25NB Quick start guide

Desa

Desa Comfort Glow CGN12A Quick start guide

Desa

Desa 6000 BTU/HR Quick start guide

Desa

Desa Comfort Glow CGN10L Quick start guide

Desa

Desa SGS3124P Quick start guide

Desa

Desa Comfort Glow CCL3018NA Quick start guide

Desa

Desa BLP35ES User manual

Popular Gas Heater manuals by other brands

Superior

Superior BGE18NV Installation and operation instructions

Dru

Dru Room-sealed atmospheric gas-fired heating... user manual

klover

klover TKR 35 user guide

Rothenberger Industrial

Rothenberger Industrial 035984 instruction manual

New Buck Corporation

New Buck Corporation 34 user manual

Hargrove

Hargrove Timberland Glow Operation and installation guide

Kinder

Kinder Cameo BF Installation and maintenance instructions

Qlima

Qlima GH 438 B-2 Directions for use

Gasmate

Gasmate AH100 Series instructions

Medallion

Medallion MBP20TLB OWNER'S OPERATION AND INSTALLATION MANUAL

Clarke

Clarke DEVIL 910SS User instructions

Superior

Superior BGE18NR Operation instructions

Brant Radiant Heaters

Brant Radiant Heaters QTD Series User instruction

L.B. White

L.B. White Therma Grow HW220 Owner's manual and instructions

Sealey

Sealey LP35.V5 instructions

Italkero

Italkero Falo Evo User manual and assembly instructions

Williams

Williams 2509822A owner's manual

Romotop

Romotop Heckla 1301 Installation, operator and maintenance manual