Denver DCH-600 User manual
ENG-1 ENG-2
(1) This product is not a toy,it's a piece of complicated equipment which integrated with
professional knowledge by mechanic,electric, air mechanics, high-frequency transmitter
and so on, so it should be installed correctly and adjusted to avoid any accidents. The
owner must always operate in a safe manner, if improper operation that caused human
injured or property damage, then we DENVER ELECTRONICS A/S accept no liability for
any safety duties from operation. As we have no control over the way they maintained,
used and operated.
(2) This product is not suitable for users under 14 years of age
(3) The use of the drone may be prohibited in some areas like train stations, airports,
aircrafts, inhabited areas etc. You should check with the authorities whether the use of
the drone is permitted in some public or private areas. Always use the drone bearing in
mind not to breach people's privacy. We exclude liability for any wrong use of the drone.
(4) We DENVER accept no liability for any safety duties or nes arising from operation,
usage or mis-control after the sale of products. Warranty does not cover if drone crashes
and get damaged.
Keep away from crowd when ying, since drone ight is a high risk hobby.
Mis-assembled or broken main frame or defective electronic equipment or unskilled
operation may cause accidents of machine damaged or injured. Please pay special
attention to safety operation.
(1) Keep away from people and obstacles
"The ying speed and status of the drone is uncertain,so it may cause potential danger."
When choosing a ying site should stay clear of buildings, trees and power lines. AVOID
ying in or near crowded areas. Meanwhile avoid ying in rain, storms,thunder and
lightening to protect machinery and parts out of damage.
(2) Keep away from Humid environments
Inside of drone is made up of precise electronic components. Stay away from humidity
or water vapor to protect machinery and parts.
(3) Safety operation
Please y your drone according to your physical status and ight skill. Fatigue, listlessness
and mis-operation will increase possibilities of accidental hazard.
(4)Keep away from rotating blades
Keep your face and body as well as all spectators away from the rotating blades. The
spinning blades of a model of this type can cause serious injury.
(5) We recommend to y the drone below 10 meters of height.
A drone is made up of metal, ber,plastic,electronic components,etc. So keep it away
from heat and sunshine to avoid distortion, and damage.
1.Instructions
Please read the user handbook carefully and then keep it in a safe place for future
consultation and maintenance.
1.1 Important Notice
1.2 Safety Precautions
1.3 Check List Before First Flight
DENVER DCH-600
(1) Flying eld should be in an open space and we suggest at least
5M length *5M wide*3M height.
(2) Make sure the drone is fully charged.
www.facebook.com/denverelectronics
Left Trigger
(360° Flip Mode on/off)
Right Trigger
(signal lights on/off)
1.7*6PB Screw
1. Drone overview
2. Controller
Trim rotation
Power Indicator
Left Stick
(throttle and rotate)
Camera Button
(take photo)
Video Button
(recording on/off)
LCD Screen
Right Stick
(move left / right and
forward / back)
Trim left / right
Trim forward / back
360° Eversion
(instant ip)
Mode
(1: beginner, 2: expert)
PRODUCT PARTS
BLADE GUARD INSTALLATION
ENG-3 ENG-4
LED Signal Lights
LED Running
Lights
Black Blade A
Clockwise
White Blade A
Clockwise White Blade B
Counter-clockwise
Black Blade B
Counter-clockwise
Blade Guard
LED Signal
Lights
(3) please strictly obey the order of turn-on, turn-off before operation.Whenstarting your
ight,rst turn on the transmitter,and connect power cable of drone last; When nishing
your ight,please disconnect the power cable of your drone rst,turn off transmitter last.
An upset in the order of connection may cause your drone loose control to threaten
yourself and others safety. Please follow a correct habit of turn-on and turn-off.
(4) make sure the connection is solid between battery or motor.
The ongoing vibration may cause bad connection of power terminal and make the
drone uncontrollable.
1.To reduce the risk of re or electric shock, do not expose this apparatus to rainor
moisture. The apparatus shall not be exposed to dripping or splashing and that objects
lled with liquids, such as vases, shall not be placed on apparatus.
2.The direct plug-in adapter is used as disconnect device, the disconnect device shall
remain readily operation.
3.This equipment is a Class II or double insulated electrical appliance. It has been
designed in such a way that it does not require a safety connection to electrical earth.
4.This lightning ash with arrowhead symbol within an equilateral triangle is intended to
alert the user to the presence of non-insulated “dangerous voltage” within the
product’s enclosure that may be of sufcient magnitude to constitute a risk of electric
shock. To reduce the risk of electric shock, do not remove cover (or back) as there are
user serviceable parts inside. Refer servicing to qualied personnel. The exclamation
point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance instructions in the literature accompanying the
appliance.
5.Correct Disposal of this product. This marking indicates that this product should not be
disposed with other household wastes throughout the EU. To prevent possible harm to
the environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To return your
used device, please use the return and collection systems or contact the retailer where
the product was purchased.
Warning:
No function
The Li-Po batteries may be recycled
Please discard old batteries in a proper recycling station.
Do not throw batteries in the regular trash. If you have questions,
please contact your local environmental agency to collect old batteries.
1. Charge the Battery
2. Warnings
Connect the Li-Po battery to USB before plugging the USB to power or your
computer. One end of the USB charger goes into any free port on your computer
The other end plugs into your battery. You may leave the battery in your copter, or
remove it for external charging. While charging, the light will be on solid red. When
charging is complete, the light will blink. The recharge time should be around 120
minutes.When the battery runs low, the transmitter will activated a “di, di” sound
alarm, and the LED lights on the quadcopter will ash. This indicates that the battery
has only a short time left, so y the drone back immediately for retrieval.
1. The blade guards are removable. To install each blade guard, press the square area
at the bottom of the guard against the matching section of the drone. Use the
supplied screws to attach each of the 4 guards.
2. Keep the guards installed to protect the drone and users, or remove the guards for
lighter weight and more speed and maneuverability. Note that the blades (propellers)
are easy to replace, but each blade is different. If the incorrect rotation-style of blade
is used, the quadcopter will not y.
CHARGING LI-PO BATTERY
ENG-5 ENG-6
This product is equipped with a Li-Po battery. Please take note of appropriate safety
precautions when not in use.
Do not expose the charged battery to high temperatures, such as ames or near
electronic devices. This may cause damage or explosion.
Make sure all batteries are connected in the proper orientation to avoid damage or
explosion.
Do not use the battery to impact any hard surfaces. Avoid contact with metal.
If the battery becomes damaged, bulges, or appears to change shape, please stop
using the battery and discard it.
When charging the battery, to avoid accident, put the power supply on the ground.
Avoid setting the charger on cloth or other ammable materials becausethe charger
will get hot.
Do not immerse the battery in water. The battery should be kept in a dry place.
Do not break the battery or attempt to open the battery.
Do not leave the battery charging without supervision.
When the battery is not being used for a long time, remove it and put it in a safe dry
place.
*
*
*
*
*
*
*
*
*
*
* For safety, make sure the switch beneath the drone is in the OFF position before
you electrically connect the battery cables. Connect the battery to the
drone by gently plugging the cable on the battery to the power cable
underneath the drone. Make the sure receptacles are oriented correctly so that
one receptacle slides smoothly into the other.
* To disconnect the battery, grasp the plastic receptacles with your ngers. Never
pull the cables apart by pulling on the cables.
Connect Battery
* Install the Li-Po battery in the drone,
press the tab at the front of the battery compartment
down to access the battery compartment, and insert
the battery base-rst into the compartment so that
the cable on the battery is exposed.
* To remove the Li-Po battery from the drone, press
down on the tab with one hand and grasp the
battery with your other hand to pull the battery out
by its sides (never pull the battery out by its cables).
To assemble the Controller, install 4 1.5V AA
batteries (not included) in the controller/ transmitter.
You may need a small screwdriver to open and
then close the cover over the battery compartment.
FLIGHT PREPARATION
Press Down on
Tab to Access
Battery Compartment
Lithium battery inside!
Do not try to open the product!
Do not expose to heat, water,
moisture, direct sunlight!
Warning
CAUTION!
3. Connect the Battery
2. Install Li-Po Battery in DCH-600
1. Install 4 AA Batteries in Controller
ENG-7 ENG-8
1. Up / Down (Throttle)
Push the LEFT ST ICK left or right to
rotate the direction the drone is
facing (yaw).
Release the stick to stop rotating.
2. Rotate Direction
3. Move Left / Right
Push the RIGHT STICK left to move
left, or right to move right.
Release the stick to stop moving.
Push the RIGHT STICK forward to
move forward, or back to move
backwards.Release the stick to stop
moving.
4. Move Forward / Backwards
If the drone rotates when the stick
is centered, click this switch left
or right until the drone is stable.
5. Adjust Rotation Trim (Yaw)
FLIGHT CONTROL
Push the LEFT STICK forward to
make the drone go up, or backward
to go down (throttle). The throttle
will stay where you leave it.
NOTE: The drone will not operate unless you follow these steps in the order
listed.
1. First make sure the drone is OFF. Turn the controller / receiver ON. This
procedure must be followed precisely for the controller and drone to nd and
bind with each other.
2. The controller will beep once and the light will blink rapidly. Move the LEFT STICK
to the top and then to the bottom. The controller will stop blinking to show the
throttle is calibrated. Leave the stick at the bottom.
3. Now turn the drone ON by ipping the switch underneath the drone to the ON
position. After about 3 second the controller will beep “di do di”. The lights on
the drone will stop ashing. This shows the drone has become bound to the
controller.
4. Put the drone on level ground. Move the
RIGHT STICK on the controller in a circle.
The controller will beep “di do di” and
the drone lights will blink briey. This
calibrates the drone gyroscopes for level
ying.
Power Switch
PRE-FLIGHT ADJUSTMENTS
OFF ON
To do an instant ip simply press the 360° Eversion button on the front of the controller,
the drone will ip forward 360°.
Warning: Do not perform a 360° ip unless the drone has enough space for safety.
Left Trigger
360° Eversion button
VIDEO AND CAMERA OPERATION
ENG-9 ENG-10
Camera
State LED
Micro-SD
Storage Card
Press the Mode button on lower right of the controller to switch between Flight
Mode 1 (maximum Gyro-stability) and Mode 2 (3D expert control). The LCD screen will
indicate the current mode.
Mode 1 automatically uses the 6-Axis Gyro (3 gyroscopes and 3 accelerometers) to its
full capabilities for stable, level ight. Use this mode for beginners, or to hover for
movies and snapshots.
Mode 2 tilts the drone more sharply (stronger pitch and roll), for faster acceleration.
Use this mode for racing and 3D maneuvers.
The drone can easily ip in an entire 360° circle. The drone will quickly stabilize and
level out, but will lose some altitude, so rst make sure the drone is ying high above
the ground.
To ip in the direction you choose, rst press the LEFT TRIGGER. The controller will
start beeping and enter 360° Flip Mode. Push the RIGHT STICK to ip in the desired
direction (forward, backward, left, or right) and return to normal ight. When the battery
runs low, the transmitter will activated a “di, di” sound alarm, the LED lights on the
drone will ash and the ip action will be auto turn off.
If the drone drifts to the side when
the stick is centered, click this switch
left or right until the drone is stable.
6. Adjust Left/Right Trim (Roll)
FLIGHT MODES
360° FLIPS
If the drone drifts forward or back
when the stick is centered, click this
switch forward or backward until
the drone is stable.
7. Adjust Forward/Backward Trim (Pitch)
1. If a storage card is not already installed, install a micro-SD ( “not included”) storage
card in the camera underneath the drone. See the small sketch on the camera itself,
which shows how to orient the chip correctly. Press the chip in until it clicks and stays.
2. To take a photograph, press the Camera Button on the front of the controller.The red
Camera State LED underneath the drone will blink on for about 2 seconds then off
indicating that the drone has taken a single, still photo.
3. To record video, press the Video Button on the front of the controller to start
recording. The red Camera State LED underneath the drone will come on to show
that video is being recorded. Press the Video Button against to stop recording.
Note: Always remember to stop the video recording with the controller before
shutting down. If the drone is switched off while still recording, the AVI le
being stored on the micro-SD card might not be “closed” or stored properly.
4. To quickly retrieve your videos and photos, connect the micro SD card reader
(included) to your computer. Optionally, you have remove the micro-SD storage card
and access the card directly with your computer. The data on the micro-SD card will
appear in folders as JPEG les and AVI les, which you can move to your computer.
If the propeller is damaged in the ight, you can replace with included spare
propeller according to below steps.
1. Propellers replacement
INSTALLATION OF PROPELLERS
ENG-11 ENG-12
Camera Button
Video Button
Remove the screw of props
and replace with new one
ALL RIGHTS RESERVED, COPYRIGHT DENVER ELECTRONICS A/S
All cities have established collection points, where electric and electronic equipment
and batteries can either be submitted free of charge at recycling stations and other
collection sites, or be collected from the households. Additional information is
available at the technical department of your city.
Hereby, Inter Sales A/S, declares that this product DCH-600 is in compliance with
the essential requirements and other relevant provisions of Directive 1999/5/EC.
A copy of the Declaration of conformity may be obtained at: Inter Sales A/S,
Stavneagervej 22, DK-8250 Egaa, Denmark.
Imported by:
DENVER ELECTRONICS A/S
Stavneagervej 22
DK-8250 Egaa
Denmark
www.facebook.com/denverelectronics
Electric and electronic equipment and included batteries contains materials,
components and substances that can be hazardous to your health and the
environment, if the waste material (discarded electric and electronic equipment and
batteries) is not handled correctly.
Electric and electronic equipment and batteries is marked with the crossed out trash
can symbol, seen below. This symbol signies that electric and electronic equipment
and batteries should not be disposed of with other household waste, but should be
disposed of separately.
As the end user it is important that you submit your used batteries to the approriate
and designated facility. In this manner you make sure that the batteries are recycled
in accordance with legislature and will not harm the environment.
Table of contents
Other Denver Drone manuals
