Delta VF-MD How to use
Delta VF-MD drive short manual for encoder model
Drive I/p connections: L1- PHASE, L2-NEUTRAL
Drive o/p connections: U, V, W TO MOTOR
Control terminals: DCM-door common signal
REV- door open signal
FWD-door close signal
Encoder terminals: VP-red wire, black-DCM, yellow-A, blue-B (put dip
switch in +12v mode) .this switch near to VP terminal.
Door feedback signals: Door close limit signal-RC1 (com), RB1 (NC), RA1
(no), Door open limit signal-RC2 (com), RA2 (no)
Drive program:
User parameters:
0-17-30 %( vary depend on site) , 0-18-1
Basic parameters:
1-00-50.0, 1-01-50.0, 1-02-220volts,1-07-6.0
Motor and feedback parameters:
2-02-0.2(put first), 2-01-0.58, 2-04-6, 2-11-50, 2-12-1, 2-13-450, 2-14-50, 2-
18-20
Motor auto tuning –put 0-12-0, then press run command for auto tuning.
After this check motor direction by press run command door should close
.if direction reverse interchange two motor wires and repeat motor tuning
again
Door open control parameters:
3-00 -6, 3-01-20, 3-02 -20, 3-03 -90, 3-04-6.0, 3-05-95, 3-06-4.0, 3-12-20,
3`-17-999.9
Door close control parameters:
4-00 -18.0, 4-01-15.0, 4-02 -6.0, 4-03 -5.0, 4-04-4.0, 4-15-20, 4-22-999.9
Digital output parameters: 6-00-21, 6-01-22
Door width tuning process: 1.put door in half position ,after this enter
parameter 0-12-0, 2-23-1 then give run command ( in this time the door
open and close completely ) if tuning complete successfully ok .go to step3.
1. If you get AUE error immediately increase value slightly in 0-17
parameter
2. if you get AUE error after full open and close change the value in 2-
12-1 0r 2
3. In door width tuning the door close completely first then open ,if the
door not open you decrease the value slightly in 0-17 upto opening
4. If you get PGER error check the encoder direction this you change
value 2-12-1 or 2
5. Put 0-12-1, Check door operation by door open and close signals.
Note: how to calculate 0-17 parameter value depends on site
0-17= 100xsite current (check in drive in constant speed
running)/2.5amps (drive current)
For example at 6 Hz speed motor takes 0.5 amps current then
0-17=100x0.5/2.5=20+ (3 to 5 extra) =23 or 25
Note: for reset the drive put parameter 0-02-09 (for restore the parameters
into default values.)
if you have any queries please call to 9600073866
Table of contents
Other Delta Media Converter manuals
Delta
Delta PMC-24V150W2AA User manual
Delta
Delta PMC-24V050W1AA User manual
Delta
Delta PMC-12V100W1AA User manual
Delta
Delta PMH-24V50WCA Series User manual
Delta
Delta PMC-05V050W1AA User manual
Delta
Delta DHI-NVD0405DH-4K User manual
Delta
Delta SCART-HDMI2 User manual
Delta
Delta M-203G User manual
Delta
Delta M-023G User manual
Delta
Delta C2000 Series User manual
Delta
Delta DCS 480 User manual
Delta
Delta 061047A User manual
Delta
Delta IPM-AE7-0020A User manual
Delta
Delta AC01 User manual
Delta
Delta PMC-24V150W1BA User manual
Delta
Delta VFD-L Series User manual
Delta
Delta DA/AU-3 User manual
Delta
Delta VS-82 User manual
Delta
Delta PMC-DSPV100W1A User manual
Delta
Delta PMC-12V050W1AA User manual
