Delta DVP04PT-E2 User manual

DVP-0280530-02

20220112

- 1 -

………………………………………………………………… ENGLISH …………………………………………………………………

Thank you for choosing Delta’s DVP series PLC. DVP04/06PT-E2 temperature

measurement module receives 4/6 points of thermal resistance temperature sensors

and converts them into 16-bit digital signals. Users can select the temperature to be

displayed in Celsius (°C) or Fahrenheit (°F). Resolution of temperature in Celsius: 0.1°C

and in Fahrenheit: 0.18°F. In addition, you can access the data in the module by

applying FROM/TO instructions or read the average value of channels directly by using

MOV instruction (Please refer to allocation of special registers D9900 ~ D9999).

EN DVP04/06PT-E2 is an OPEN-TYPE device. It should be installed in a control

cabinet free of airborne dust, humidity, electric shock and vibration. To prevent

non-maintenance staff from operating DVP04/06PT-E2, or to prevent an accident

from damaging DVP04/06PT-E2, the control cabinet in which DVP04/06PT-E2 is

installed should be equipped with a safeguard. For example, the control cabinet

in which DVP04/06PT-E2 is installed can be unlocked with a special tool or key.

EN DO NOT connect AC power to any of I/O terminals, otherwise serious damage

may occur. Please check all wiring again before DVP04/06PT-E2 is powered up.

After DVP04/06PT-E2 is disconnected, Do NOT touch any terminals in a minute.

Make sure that the ground terminal on DVP04/06PT-E2 is correctly grounded

in order to prevent electromagnetic interference.

FR DVP04/06PT-E2 est un module OUVERT. Il doit être installé que dans une

enceinte protectrice (boitier, armoire, etc.) saine, dépourvue de poussière,

d’humidité, de vibrations et hors d’atteinte des chocs électriques. La protection

doit éviter que les personnes non habilitées à la maintenance puissent accéder à

l’appareil (par exemple, une clé ou un outil doivent être nécessaire pour ouvrir a

protection).

FR Ne pas appliquer la tension secteur sur les bornes d’entrées/Sorties, ou l’appareil

DVP04/06PT-E2 pourra être endommagé. Merci de vérifier encore une fois le

câblage avant la mise sous tension du DVP04/06PT-E2. Lors de la déconnection

de l’appareil, ne pas toucher les connecteurs dans la minute suivante. Vérifier

que la terre est bien reliée au connecteur de terre afin d’éviter toute

interférence électromagnétique.

Product Profile & Dimension

Removable I/O terminal

Direct mounting hole

Mounting slot

(35mm)

Power / A->D / Error indicators

I/O module

connection port

I/O terminal No.

Model Name

I/O module clip

[ Figure 1 ]

I/O module connection port

04PT-E2

4AI- PT

[ Figure 2 ]

106

61.5

110

Unit: mm

- 2 -

 External Wiring

*1: Wiring for analog input should adopt cables of Ni100/Ni1000, Pt100/Pt1000, Cu50/Cu100,

JPt100, LG-Ni100 or other temperature sensor cables or double shielded cable and should

be separated from other power cables that may cause interference. Please apply 3-wire for

PT100 / PT1000. If a 2-wire sensor is applied, please short-circuit In+ and In- terminals

(n=1~6).

*2: When resistance is

0 to 300Ω/ 0 to 3000Ω, we suggest using 2-wire or 3-wire sensor and

not 4-wire.

*3: Choosing the Appropriate Sensor

● DVP06PT-E2: If using Ni100, Pt100, JPt100, Cu50 or Cu100 temperature sensor and 300Ω

resistor, the internal excitation current is 1.0389 mA; if using Ni1000, Pt1000 or LG-Ni1000

temperature sensor and 3000Ωresistor, the internal excitation current is 208.3μA.

● DVP04PT-E2: If using Ni100, Pt100 and 300Ωresistance sensor, the internal excitation current is

1.53mA; if using Ni1000, Pt1000 and 3000Ωresistance sensor the internal excitation current is

200μA.

*4. Connect FE with terminal for noise suppression.

Note 1: The 3-wire has an even length. A wire length is less than 200m and a wire resistance is less

than 20Ω.

Note 2: Please refer to functions specifications regarding supported sensor types for different types

of products.

I/O Terminal Layout

I4+O4+FE0V24V

DVP04PT-E2 (4AI)

FEI4-

I2+O2 +FEI1-I1+O1+ FEI3-I3+O3+FEI2-

12 345678910 1 1 12



I5+O5+FE0V24V

DVP06PT-E2 (6AI)

I5-

I2+O2+I1-I1+O1+

I3-I3+O3+

I2-

123 456789101112

1234567 89101112

I6+O6+ I6-

I4-I4+O4+

12345 678

Electrical Specifications

DVP04/06PT-E2

Power supply voltage 24VDC (20.4VDC ~ 28.8VDC) (-15% ~ +20%)

Max. rated power

consumption 1.5W, supplied by external power source

Connector European standard removable terminal block (Pin pitch: 5mm)

- 3 -

DVP04/06PT-E2

Operation/storage Operation: 0°C~55°C (temp.), 5~95% (humidity), Pollution degree2

Storage: -25°C~70°C (temp.), 5~95% (humidity)

Vibration/shock

immunity

International standards: IEC61131-2, IEC 68-2-6 (TEST Fc)/

IEC61131-2 & IEC 68-2-27 (TEST Ea)

Series connection to

DVP-PLC MPU

The modules are numbered from 0 to 7 automatically by their

distance from MPU. No.0 is the closest to MPU and No.7 is the

furthest. Maximum 8 modules are allowed to connect to MPU and

will not occupy any digital I/O points.

Functions Specifications

DVP04/06PT-E2 Celsius (°C) Fahrenheit (°F) Input

Impedance

Analog input

channel 4/6 channels

Digital data format 2’s complement of 16 bits

Response time 200ms / each channel

Overall accuracy ±0.3% when in full scale (25°C, 77°F)

±0.6% when in full scale within the range of 0 ~ 55°C, 32 ~ 131°F

Applicable sensor

type

04PT：3-Wire Pt100 (DIN 43760-1980 JIS C1604-1989, 100Ω3850 PPM/°C);

Pt1000 (DIN EN60751, 1 kΩ3850 PPM/°C); Ni100 / Ni1000(DIN 43760); 0 ~

300Ω/0 ~ 3000Ωinput impedance

06PT：3- Wire Pt100 (DIN 43760-1980 JIS C1604-1989, 100Ω3850 PPM/°C);

Pt1000 (DIN EN60751, 1 kΩ3850 PPM/°C) ; Ni100 / Ni1000(DIN 43760)；

Cu50；Cu100；JPt100 (JIS C1604-1989)；LG-Ni1000；0 ~ 300Ω/0 ~ 3000Ωinput

impedance

Input temperature

range

Pt100: -180°C ~ 800°C

Ni100: -80°C ~ 170°C

Pt1000: -180°C ~ 800°C

Ni1000: -80°C ~ 170°C

JPt100: -180°C ~ 500°C

Cu50: -50°C ~ 150°C

Cu100: -50°C ~ 150°C

LG-Ni1000: -50°C ~ 180°C

Pt100: -180°C ~ 800°C

Ni100: -80°C ~ 170°C

Pt1000: -180°C ~ 800°C

Ni1000: -80°C ~ 170°C

JPt100: -180°C ~ 500°C

Cu50: -50°C ~ 150°C

Cu100: -50°C ~ 150°C

LG-Ni1000: -50°C ~ 180°C

0 ~ 300Ω

0 ~ 3000Ω

Range of digital

conversion

Pt100: K-1,800 ~ K8,000

Ni100: K-800 ~ K1,700

Pt1000: K-1,800 ~ K8,000

Ni1000: K-800 ~ K1,700

JPt100: K-1,800 ~ K5,000

Cu50: K-500 ~ K1,500

Cu100: K-500 ~ K1,500

LG-Ni1000: K-500 ~ K1,800

Pt100: K-1,800 ~ K8,000

Ni100: K-800 ~ K1,700

Pt1000: K-1,800 ~ K8,000

Ni1000: K-800 ~ K1,700

JPt100: K-1,800 ~ K5,000

Cu50: K-500 ~ K1,500

Cu100: K-500 ~ K1,500

LG-Ni1000: K-500 ~ K1,800

K0 ~ K3,000

K0 ~ K30,000

Resolution 0.1°C 0.18°F*1 0.1Ω

Average function Range: K1 ~ K100.

Self-diagnosis Upper and lower bound detection in all channels

Isolation

Optical coupler isolation between digital circuits and analog circuits. No isolation

among analog channels.

500VDC between digital circuits and Ground

500VDC between analog circuits and Ground

500VDC between analog circuits and digital circuits

500VDC between 24VDC and Ground

*1: The unit of temperature would be displayed as 0.1°C/0.1°F. If the temperature unit is set to be

Fahrenheit, the second decimal place would not be shown.

Control Register

04P 06P Attrib. Register content Description

#0 #0 O R Model name

DVP04PT-E2 model code = H’0082

DVP06PT-E2 model code = H’00C2

#1 #1 O R Firmware version Display the current firmware version in hex.

- 4 -

04P 06P Attrib. Register content Description

#2 #2 O R/W CH1 Input mode setting Input mode: Default = H’0000. Take CH1 for example:

Mode 0 (H’0000): Pt100: -180°C ~ 800°C

Mode 1 (H’0001): Ni100: -80°C ~ 170°C

Mode 2 (H’0002): Pt1000: -180°C ~ 800°C

Mode 3 (H’0003): Ni1000: -80°C ~ 170°C

Mode 4 (H’0004): 0~300Ω

Mode 5 (H’0005): 0~3000Ω

Mode 6 (H’0006): JPt100 (-180°C ~ 500°C)

Mode 7 (H’0007): Cu50 (-50°C ~ 150°C)

Mode 8 (H’0008): Cu100 (-50°C ~ 150°C)

Mode 9 (H’0009): LG-Ni1000 (-50°C ~ 180°C)

Mode -1 (H’FFFF): Channel 1 unavailable

Note: 04PT-E2 do NOT support mode 6-9.

#3 #3 O R/W CH2 Input mode setting

#4 #4 O R/W CH3 Input mode setting

#5 #5 O R/W CH4 Input mode setting

#6 O R/W CH5 Input mode setting

#7 O R/W CH6 Input mode setting

O R/W Temperature unit setting

Select the temperature unit (Celsius °C / Fahrenheit °F).

Default = H’0(°C)

#8 #8 O R/W CH1 sampling range

Set sampling range:

Range = K1 ~ K100

Default = K10

#9 #9 O R/W CH2 sampling range

#10 #10 O R/W CH3 sampling range

#11 #11 O R/W CH4 sampling range

#12 O R/W CH5 sampling range

#13 O R/W CH6 sampling range

#12 #14 X R Average temperature measured at CH1

Average temperature measured.

Setting Temperature Unit :

●DVP04PT-E2：CR#7

●DVP06PT-E2：CR#27

#13 #15 X R Average temperature measured at CH2

#14 #16 X R Average temperature measured at CH3

#15 #17 X R Average temperature measured at CH4

#18 X R Average temperature measured at CH5

#19 X R Average temperature measured at CH6

#20 #20 X R Present temperature measured at CH1

Present temperature measured.

Setting Temperature Unit :

●DVP04PT-E2：CR#7

●DVP06PT-E2：CR#27

#21 #21 X R Present temperature measured at CH2

#22 #22 X R Present temperature measured at CH3

#23 #23 X R Present temperature measured at CH4

#24 X R Present temperature measured at CH5

#25 X R Present temperature measured at CH6

#26 O R/W

Mode 4 (H’0004): 0~300Ω. Temperature

display decimal digit changes

In mode 4 (0~300Ω), temperature display decimal

changes (0: 1 digit after the decimal place/ 1: 2 digits

after the decimal place). Default= H0

#27 O R/W Temperature unit setting

Select the temperature unit (Celsius °C / Fahrenheit °F).

Default = H’0(°C)

#28 #28 O R/W Adjusted offset value of CH1

Adjusted offset value measured, range K-1000 ~ K1000.

Default = K0

Measured Value = Original Value – Adjusted offset value

Unit Setup:

●DVP04PT-E2：CR#7

●DVP06PT-E2：CR#27

#29 #29 O R/W Adjusted offset value of CH2

#30 #30 O R/W Adjusted offset value of CH3

#31 #31 O R/W Adjusted offset value of CH4

#32 O R/W Adjusted offset value of CH5

#33 O R/W Adjusted offset value of CH6

#40 #40 O R/W Function: Set value changing prohibited Prohibit set value changing, b0~b5 corresponds to CH1 ~

CH6. Default =H’0000

#41 #41 X R/W Function: Save all the set values Save all the set values. Default =H’0000

#43 #43 X R Error status Register for storing all error status. See the table of error

status for more information.

- 5 -

04P 06P Attrib. Register content Description

#100 #100 O R/W Function: Enable/Disable limit detection Upper and lower bound detection, b0~b5 corresponds to

CH1 ~ CH6 (0: Disable/ 1: Enable). Default= H’0000.

#101 #101 X R/W Upper and lower bound status

Display the upper and lower bound status (0: Not

Exceeding; 1: Exceeding upper and lower bound value),

b0~b5 corresponds to CH1 ~ CH6 lower bound, b8~b13

corresponds to CH1 ~ CH6 upper bound.

Default =H’0000

#102 #102 O R/W Set value of CH1 upper bound

Set upper bound value. Default = K32000.

#103 #103 O R/W Set value of CH2 upper bound

#104 #104 O R/W Set value of CH3 upper bound

#105 #105 O R/W Set value of CH4 upper bound

#106 O R/W Set value of CH5 upper bound

#107 O R/W Set value of CH6 upper bound

#108 #108 O R/W Set value of CH1 lower bound

Set lower bound value. Default = K-32000.

#109 #109 O R/W Set value of CH2 lower bound

#110 #110 O R/W Set value of CH3 lower bound

#111 #111 O R/W Set value of CH4 lower bound

#112 O R/W Set value of CH5 lower bound

#113 O R/W Set value of CH6 lower bound

Symbols: O: When CR#41 is set to H’5678, the set value of CR will be saved;

X: set value will not be saved

R: able to read data by using FROM instruction

W: able to write data by using TO instruction.

Module Reset: Write H’4352 into CR#0; the action can re-initialize all parameter settings to ensure normal function. Connect only 1

device (preferred) for module reset and then wait 1 sec. to execute power outage.

※ CR#43: Error status value. See the table below:

Description

bit0 K1 (H’1) Power supply error bit7 K128 (H’80) CH5 Conversion error

bit1 K2 (H’2) Reserved bit8 K256(H’0100) CH6 Conversion error

bit2 K4 (H’4) Upper / lower bound error bit9 K512(H’0200) Mode setting error

bit3 K8 (H’8) CH1 Conversion error bit10 K1024(H’0400) Sampling range error

bit4 K16

(H’10) CH2 Conversion error bit11 K2048(H’0800) Upper / lower bound

setting error

bit5 K32

(H’20) CH3 Conversion error bit12 K4096(H’1000) Set value changing

prohibited

bit6 K64

(H’40) CH4 Conversion error bit13 K8192(H’2000)

Communication

breakdown on next

module



Note: Each error status is determined by the corresponding bit (b0 ~ b15) and there may be more

than 2 errors occurring at the same time. 0 = normal; 1 = error

PID Control Registers

Note 1: CH5 and CH6 in DVP06PT-E2 do not support PID control.

CR# Attrib. Register content Description

CH1 CH2 CH3 CH4

#120 #140 #160 #180 O R/W Set temperature

value

Please set the temperature value

according to proper range of each

sensor type. Default = K0

- 6 -

CR# Attrib. Register content Description

#121 #141 #161 #181 O R/W Sampling time (s) Range: K1 ~ K30 (s). Default = K2

#122 #142 #162 #182 O R/W KPProportional control constant.

Default = K121

#123 #143 #163 #183 O R/W KIIntegral constant. Default = K2,098

#124 #144 #164 #184 O R/W KDDerivative constant. Default = K-29

#125 #145 #165 #185 O R/W Upper limit of I value Upper limit of I value. Default = K0

#126 #146 #166 #186 O R/W Lower limit of I value Lower limit of I value. Default = K0

#127 #147 #167 #187 X R I value Current accumulated offset value

#128 #148 #168 #188 O R/W Heating/cooling 0: Heater, 1: Cooler. Default = K0

#129 #149 #169 #189 O R/W Upper limit of output Upper limit of output. Default =

K32,000

#130 #150 #170 #190 O R/W Lower limit of output Lower limit of output. Default = K0

#131 #151 #171 #191 X R Output percentage Output percentage (Unit: 0.1%)

#132 #152 #172 #192 X R Output width (ms) Width of control output. Unit: ms

#133 #153 #173 #193 X R Output cycle (ms) Cycle of control output. Unit: ms

#134 #154 #174 #194 X R Output volume Output volume

#135 #155 #175 #195 X R/W PID_RUN/STOP 0: STOP, 1: RUN. Default = K0

#136 #156 #176 #196 X R/W Auto-tuning 0: Disabled, 1: Auto-tuning. Default

= K0

 Explanation on Special Registers D9900~D9999

When DVP-ES2 MPU is connected with modules, registers D9900~D9999 will be

reserved for storing values from modules. You can apply MOV instruction to operate

values in D9900~D9999.

When DVP-ES2 MPU is connected with DVP04/06PT-E2, the configuration of special

registers is as below:

Note 1: D9900 ~ D9999 are average input values of CH1 ~ CH4 and the sampling range is K1 ~ K100.

When the sampling range is set to K1, the values displayed in D9900~D9999 are current values.

You can use: 1. ES_AIO Configuration Function of WPLSoft or 2. FROM/TO instructions (CR#8

~ CR#11) to set the sampling range as K1.

Module

#7 Description

D1320 D1321 D1322 D1323 D1324 D1325 D1326 D1327 Model Code

D9900 D9910 D9920 D9930 D9940 D9950 D9960 D9970 CH1 average

temperature

D9901 D9911 D9921 D9931 D9941 D9951 D9961 D9971 CH2 average

temperature

D9902 D9912 D9922 D9932 D9942 D9952 D9962 D9972 CH3 average

temperature

D9903 D9913 D9923 D9933 D9943 D9953 D9963 D9973 CH4 average

temperature

D9904 D9914 D9924 D9934 D9944 D9954 D9964 D9974 CH5 average

temperature

D9905 D9915 D9925 D9935 D9945 D9955 D9965 D9975 CH6 average

temperature

- 7 -

 Adjust PT Conversion Curve

Users can adjust the conversion curves according to the actual needs by changing the

Offset value.

Offset in DVP04/06PT-E2: Deviation digital value from the target value.

(Measured Value= Original Value – Adjust Value Offset)

Mode0 ~ Mode3, Mode6 ~ Mode9 : 0.1˚

Mode4 ~ Mode5: 0.1Ω

Mode 0：Mode 3：

+8,000

+4,000

-1,800

+800

-180

+4000

Digital output

Measured

temperature input

+3,380

-1,120

+338

-112

Digital output

Measured

temperature input

Mode 1: Mode 4:

+1,700

-800

+170

-80

Digital output

Measured

temperature input

+3,000

300

Digital output

Measured input

impedance

Mode 2: Mode 5:

+14, 720

+7,360

-2,920

+1,472

-292

+7360

Digital output

Measured

temperature input

+30,000

3,000

Measured

Inpu t

Impedance

D i g i ta l Ou tp u t

- 8 -

………………………………………………………………繁體中文 …………………………………………………………………………

感謝您採用台達 DVP 系列產品。DVP04/06PT-E2 溫度量測模組接受外部 4/6 點熱電阻溫

度感測器，將其轉換成 16 位元的數位信號。使用者可選擇攝氏溫度(°C)或華氏(°F)溫度，

攝氏溫度輸入解析度為 0.1°C，華氏溫度輸入解析度為 0.18°F。並可透過主機以 FROM /

TO 指令來讀寫模組內資料，或者以 MOV 指令直接讀取對應通道平均值(請參閱 D9900 ~

D9999 特殊暫存器使用說明)。

本安裝說明書提供給使用者電氣規格、功能規格、安裝配線之相關注意事項。其他詳

細之程式設計及指令說明請見 DVP-ES2 操作手冊【程式篇】，選購之周邊裝置詳細說

明請見該產品隨機安裝說明書。

本機為開放型 (OPEN TYPE) 機殼，因此使用者使用本機時，必須將之安裝於具防

塵、防潮及免於電擊⁄衝擊意外之外殼配線箱內。另必須具備保護措施（如：特殊之工

具或鑰匙才可打開）防止非維護人員操作或意外衝擊本體，造成危險及損壞。

交流輸入電源不可連接於輸入⁄出信號端，否則可能造成嚴重損壞，請在上電之前再次

確認電源配線。請勿在上電時觸摸任何端子。本體上之接地端子務必正確的接地，

可提高產品抗雜訊能力。

 產品外觀尺寸與部位介紹

機種型號

電源、及錯誤A->D 指示燈

輸出／入端子編號

脫落式輸出／入端子

直接固定孔

DIN (35mm)軌槽

I/O 模組連接埠

I/O 模組固定扣

I/O 模組連接埠

04PT-E2

4AI- PT

詳細尺寸圖請參閱英文版之 Figure2，單位：mm。

 外部配線



Ni100Pt100,JPt100,

Cu50, Cu100/

Ni 10 0 0 , P t1 0 0 0 ,

LG-Ni1000 *3

隔離線*1

ADC

INA

隔離線*1

CH1

2-Wire

CH4

3-Wire

O1+

I1+

I1-

0~300

Ni100/Ni1000/Pt100/Pt1000

Cu50/Cu100/JPt100/LG -Ni1000

Ω ,0~3000Ω

0~300

Ni100/Ni1000/Pt100/Pt1000

Cu50/Cu100/JPt100/LG-Ni1000

Ω, 0~3000Ω

O4+

I4+

I4-

*1：使用於類比輸入的配線應採用 Ni100/Ni1000、Pt100/Pt1000、Cu50/Cu100、JPt100、

LG-Ni1000 或其它本文定義的溫度感測器之連接線或雙絞隔離線且應與其他電源線或

可能引起雜訊之接線分開。請使用 3線式溫度感測器，若欲使用 2線式溫度感測器時，

請將 In+，In-短接（n=1~6）。

- 9 -

*2：量測電阻 0~300Ω/0~3000Ω時，建議使用 2線式或是 3線式即可，不需使用到 4線

式感測器。

*3：選擇適當感測器

DVP06PT-E2：若使用 Ni100、Pt100、JPt100、Cu50 與Cu100 溫度感測器以及 0~300Ω

電阻感測器，內部激勵電流為 1.0389mA；若使用 Ni1000、Pt1000 與LG-Ni1000 溫

度感測器以及 0~3000Ω電阻感測器，內部激勵電流為 208.3μA。

DVP04PT-E2：若使用 Ni100、Pt100 以及 0~300Ω電阻感測器，內部激勵電流為

1.53mA；若使用 Ni1000、Pt1000 以及 0~3000Ω電阻感測器，內部激勵電流為 200μA。

*4：如果雜訊過大請將 FE 與接地端子連接

注意 1：三線式線材長度需等長，單一線長<200m 且單一線阻<20ohm。

注意 2：各機種所支援的感測器型式請以功能規格為主。

 輸入/輸出端子台配置

請參閱英文版之端子配置圖，在此語言版本省略說明。

 電氣規格

DVP04/06PT-E2

電源電壓 24VDC (20.4VDC ~ 28.8VDC) (-15% ~ +20%)

額定最大消耗功率 1.5W，由外部電源供應。

連接方式脫落式歐式端子座 (端點距離：5mm)

操作 ∕儲存環境操作：0°C ~ 55°C（溫度），5 ~ 95%（濕度）污染等級 2

儲存：-25°C ~ 70°C （溫度），5 ~ 95%（濕度）

耐振動 ∕衝擊國際標準規範 IEC61131-2，IEC 68-2-6 (TEST Fc) / IEC61131-2 & IEC

68-2-27 (TEST Ea)

與DVP-PLC 主機串

接說明

模組編號以靠近主機之順序自動編號由 0到7，最大可連接 8台且不佔用

數位 I/O 點數。

 功能規格

DVP04/06PT-E2 攝氏(°C) 華氏(°F) 電阻

類比訊號輸入通道 4/6 通道

數位資料格式 16 位元二補數

響應時間 200ms / 每個通道

總和精密度

0.3% 在(25°C, 77°F) 範圍內滿刻度時

0.6% 在(0 ~ 55°C, 32 ~ 131°F) 範圍內滿刻度時

適合感測器形式

04PT：3-線Pt100 (DIN 43760-1980 JIS C1604-1989，100Ω3850 PPM/

˚C)；Pt1000 (DIN EN60751，1 kΩ3850 PPM/˚C)；Ni100 /

Ni1000(DIN 43760)；0 ~ 300Ω/0 ~ 3000Ω阻抗輸入

06PT：3-線Pt100 (DIN 43760-1980 JIS C1604-1989，100Ω3850 PPM/

˚C)；Pt1000 (DIN EN60751，1 kΩ3850 PPM/˚C) ；Ni100 /

Ni1000(DIN 43760)；Cu50；Cu100；JPt100 (JIS C1604-1989)；

LG-Ni1000；0 ~ 300Ω/0 ~ 3000Ω阻抗輸入

輸入溫度範圍

Pt100: -180°C ~ 800°C

Ni100: -80°C ~ 170°C

Pt1000: -180°C ~ 800°C

Ni1000: -80°C ~ 170°C

JPt100: -180°C ~ 500°C

Cu50: -50°C ~ 150°C

Cu100: -50°C ~ 150°C

LG-Ni1000: -50°C ~ 180°C

Pt100: -292°F ~ 1,472°F

Ni100: -112°F ~ 338°F

Pt1000: -292°F ~ 1,472°F

Ni1000: -112°F ~ 338°F

JPt100: -292°F ~ 932°F

Cu50: -58°F ~ 302°F

Cu100: -58°F ~ 302°F

LG-Ni1000: -58°F ~ 356°F

0 ~ 300Ω

0 ~ 3000Ω

This manual suits for next models

Table of contents

Languages:

Other Delta Control Unit manuals

Delta

Delta TECK II 81T201BTA-MMO User manual

Delta

Delta DVP06XA-H User manual

Delta

Delta AC-160-DIN User manual

Delta

Delta MultiChoice T27 Series User manual

Delta

Delta AHBP06M1-5A User manual

Delta

Delta MULTICHOICE R22000 User manual

Delta

Delta TECK COMMERCIAL R2570-MIXLFBOX Quick start guide

Delta

Delta 1700 Series Operating and maintenance instructions

Delta

Delta TECK II 81T201BT User manual

Delta

Delta CMM-EIP02 Instructions for use

Delta

Delta DVP04TC-S User manual

Delta

Delta DVP08ST11N User manual

Delta

Delta DIGI-LAN User manual

Delta

Delta DVPSCM Series User manual

Delta

Delta TECK II Instruction manual

Delta

Delta DVP04AD-H User manual

Delta

Delta AS Series User manual

Delta

Delta CANopen DVPCOPM-SL User manual

Delta

Delta DVP04AD-H2 User manual

Delta

Delta IFD9503 Instructions for use

Delta

Delta MultiChoice Ara T27T867 Series User manual

Delta

Delta AS Series User manual

Delta

Delta T13H Series User manual

Delta

Delta FlushIQ RP76681 User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual