DELTA DORE Tywatt 5400 User manual
Tywa 5400 - 5600
Tywatt 5400
EN
Smart modular power consumption sensor
Tywatt 5600
EN
Smart electricity, water and energy (OMS)
consumption sensor
2 3
EN
1 - Recommendations
- Device intended for single-phase installations
- Mounted on a DIN rail in the electrical cabinet
- 16A max. circuit breaker required.
- Position this product as far away as possible
from other units that generate strong electrical
interference.
Prerequisites
- A smart home hub connected
to the Internet router.
- The Tydom application
(available in Play Store
and Apple Store).
16A
max.
2 - Connection
Switch off the installation power supply.
2.1 Connection instructions
for the terminals
- Strip the wires while respecting
the strip length
specied on the product.
- Push the wire fully into
the terminal.
8 mm
0,75 - 1,5 mm
Ø
2
Removal
recommendations
- Switch off the power
supply.
- Use a screwdriver to press
the button of the terminal
before removing the wire.
1
2
If you do not have access to Internet, you can set
up your Tywatt with the Tydom application using
a Wi-Fi router.
4 5
EN
2.2 Connection
LED alert:
- Solid green: Power supply OK.
- Flashing red:
Customer Information System (CIS) connection
fault
Connection of the open loop current
transformer (Ti)
Connection of the secondary:
- Connect the blue wire of the Ti to terminal 3
and the white wire to the terminal 6 of the Tywatt.
Connection of the primary:
- Open the current
transformer casing.
- Insert the substation’s
phase conductor or
conductors in keeping
with the direction of
circulation of the current
from source to load.
- Close the Ti casing and
make sure that it is
suitably locked.
ON
ON
ON
ON KL
KL
ON
KL
click
Source
Load
ON
KL
(1) Ability to connect 3 TIs in parallel at inputs 3
and 6, in order to facilitate the routing of various
measurement cables (single accumulation display
of the 3 TIs available in the Tydom application).
Up to 3 TI (1) in parallel.
Heating
Hot
water
Cooling
Outlets
Hot water
Cold water
Calories
LED
Conguration
button
*: Up to 3 OMS meters
(within the limit of max. 1
per substation to be measured).
N
N
N
L
2A
ON
1
2
1
2
OMS*
TYWATT 5600
TIC
35270-Bonnemain-FR
TYWATT 56
00
Ti
4 5 6
1 2 3
N L Ti
230V~
2 VA
6 7
EN
Customer Information System connection.
-
Connect the Customer Information System (CIS) of the
electronic meter to terminals 4 and 5 of the Tywatt.
Switch the system on again.
3 - Association
3.1 Linking with the Tydom app
From the Tydom application, select:
Settings > My home > My devices >
Add a device >
Consumption > Tywatt 5400 / 5600 > then follow the
on-screen instructions.
After pairing, select the Tywatt to congure the
substation measured by the TI (heating, hot water,
outlets, cooling).
Remember to specify the type of substation
measured on the plate of the electrical cabinet.
For installations equipped with an EM.IC (consumption
information transmitter), pair the EM.IC with the Tywatt via
the Tydom application.
Using the Tydom application, select:
Settings > My home > My devices > Consumption > Then
select your previously paired Tywatt with which you wish to
pair the EM.IC and follow the instructions.
3.2 Deleting pairing with the Tydom
application
In the Tydom application, select:
- Settings > My home > My devices >
Consumption > Select the Consumption device
corresponding to the Tywatt 5400/5600 >
Press "Delete".
3.3 Deleting pairing with a paired EM.IC
In the Tydom application, select:
- Settings > My home > My devices >
Consumption > then select the Tywatt with
which the EM.IC is paired.
- In the EM.IC window, press "Unpair".
3.4 Reset to factory settings
- Hold the button pressed for 20 seconds.
The red LED ashes, then lights up solid.
- Release.
... ... ...
>20s
Red
8 9
EN
3.5 Conguration of the OMS meter
(only for Tywatt 5600)
Compatibility
Scan the QR code to verify
the compatibility of your meter.
Each meter is identied by means of a unique
8-digit code (marking or labelling on the meter),
which you must enter in the Tywatt conguration
menu, along with the nature of the measured
substation (cold water, hot water, or heating), via
the Tydom application.
Take the nal 8 gures of the bar code or the
datamatrix.
Location on DIEHL meters
12345678
12345678
12345678
Example:
Location on Engelmann meters
WaterStar_M model
SensoStar_U model
12345678
12345678
Example:
BDAB 000180
12345678
12345678
Example:
10 11
EN
Technical specications
Modular unit
- Power supply : 230 V~ 2 VA
- Class II insulation
- Type 1 action
- Rated impulse withstand voltage: 4000 V
- Ball test temperature:
Housing: 75°C
Terminal block: 100°C
- Storage temperature: -10°C / +70°C
- Operating temperature: 0°C / +55°C
- IP 30
- Dimensions: 1 module - 18 x 90 x 71 mm
- X3D wireless remote control device:
868.7 MHz to 869.2 MHz
- Maximum wireless power < 10 mW
- Category 2 receiver
- CIS: compatible with historical and standard CIS
of a Linky meter
Open loop current transformer:
- Dimensions: 30 x 46 x 29 mm
- Internal diameter: 16 mm
- Primary current: 70 A max.
- Secondary current: 140 mA max.
04/23
www.deltadore.com
This manual suits for next models
1
Table of contents
Other DELTA DORE Security Sensor manuals
DELTA DORE
DELTA DORE DOS TYXAL + User manual
DELTA DORE
DELTA DORE DMBV TYXAL+ User manual
DELTA DORE
DELTA DORE TYXAL DOI PVC User manual
DELTA DORE
DELTA DORE TYXAL DF User manual
DELTA DORE
DELTA DORE Tyxal+ DME 180 User manual
DELTA DORE
DELTA DORE DMBE TYXAL+ User manual
DELTA DORE
DELTA DORE DMB TYXAL + User manual
DELTA DORE
DELTA DORE DU TYXAL + User manual
DELTA DORE
DELTA DORE DTX User manual
DELTA DORE
DELTA DORE TYXAL DOS User manual
DELTA DORE
DELTA DORE DMB TYXAL+ User manual
DELTA DORE
DELTA DORE TYXAL DCS User manual
DELTA DORE
DELTA DORE DMF Tyxal+ User manual
DELTA DORE
DELTA DORE DMB TYXAL+ User manual
DELTA DORE
DELTA DORE DME 90 Tyxal+ User manual
DELTA DORE
DELTA DORE DVR TYXAL+ User manual
DELTA DORE
DELTA DORE TYXAL DOI PVC User manual
DELTA DORE
DELTA DORE DMBD TYXAL+ User manual
DELTA DORE
DELTA DORE TYXAL DF User manual
DELTA DORE
DELTA DORE DMB TYXAL+ User manual
