Dell S520 User manual

Dell Interactive Projector S520 Screen/Whiteboard

PTDRV

Important Safety Instructions

WARNING: Failure to read, thoroughly

understand, and follow all instructions can result

in serious personal injury, damage to equipment,

or voiding of factory warranty! It is the installer’s

responsibility to make sure all components are

properly assembled and installed using the

instructions provided.

WARNING: Failure to provide adequate

structural strength for this component can

result in serious personal injury or damage to

equipment! It is the installer’s responsibility

to make sure the structure to which this

component is attached can support ve

times the combined weight of all equipment.

Reinforce the structure as required before

installing the component. The wall to which

the screen/whiteboard is being attached may

have a maximum drywall thickness of 5/8”

(1.6cm) for wood stud installation, and 1/2”

(1.3cm) minimum for steel stud installation.

WARNING: Use this screen/whiteboard

system only for its intended use as described

in these instructions. Do not use attachments

not recommended by the manufacturer.

WARNING: Do not use this product outdoors.

14.02 in.

(356.2 mm)

78.75 in. (2000.1 mm)

80.37 in. (2041.4 mm)

4.99 in.

(126.7 mm)

5.02 in.

(127.4 mm)

4.99 in.

(984.8 mm)

15.23 in.

(386.8 mm)

6.6 in. (167.52 mm)

1.21 in.

(30.65 mm)

41.60 in.

(1056.5 mm)

55.52 in.

(1410.1 mm)

1.67 in. (42.3 mm) 2.4 in. (60.9 mm)

28.07 in.

(712.9 mm)

Front View

Side View

Back View

Top View

Product Dimensions

1/8 in. (wood)

1/2 in. (drywall)

8 mm (concrete)

6 mm (concrete – AF6 toggler)

7/16” Wrench

#8 X 1/2” Screws (5)

1/4” Washer (3)

#8 x 3/4” Screws (1)

#8-10 Wall

Anchor (7)

Screen Bracket (3)

#8 x 1” Screws (7)

1/4” x 1-1/2”

Lag Screw (3)

Screen (1) Wall Bracket (1)

Cable Cover

Clips (2)

Cleaning Cloth (1)

Cable Cover (1)

Marker Tray (1)

Sensor Cover (1)

#2 Phillips Screwdriver

Carpenter’s Level Ruler

Tools Required for Installation

Parts

Included InstallationHardware

1. Determine desired height of image (measured

from oor) (Figure 1).

2. Determine desired center of image area (Figure 1).

3. Measure 4-1/16” up from desired height (top) of

image and 4” to the right of center of screen and

mark location (Figure 1).

4. Determine location of studs behind drywall.

5. Drill one pilot hole into a wall stud at location

marked in Step 3 (Figure 1).

Studs

Center of

Screen

Floor

73-3/4 in.

46-1/8 in.

4-1/16 in.

Figure 1

4 in.

Height

from Floor

Installation

6. Install (1) 1/4” x 1-1/2” bolt and (1) washer through

middle of bracket into previously drilled hole,

leaving 1/2” of the bolt extending from wall. Use

carpenter’s level to make sure bracket is properly

level (Figure 2).

7. Position level on top of wall bracket. Move bracket

until level. Drill (2) holes for the other bolts in wall

studs.

8. Install the other (2) 1/4” x 1-1/2” bolts and (2) 1/4”

washers in the previously drilled holes. Tighten all

bolts against wall bracket.

9. Measure down 52-1/4” on center and mark spot.

Move right and left of screen until wall studs are

found and mark (Figure 3).

10. Install the (3) screen brackets using:

Wood or steel studs: (3) supplied #8 x 1” screws.

Concrete wall or no studs: (3) supplied #8-10 wall

anchors and (3) supplied #8 x 1” screws.

11. Install projector mount. Refer to the S520 Dual

Stud Wall Mount (MSP-DCCUST2) manual. Do not

install the (2) plastic covers for mount (Figure 4).

12. Run cables for projector up through hole in wall

bracket and cover to projector location (Figure 5).

Middle Fastener

Previously

Drilled Hole

Center of Screen

IR Sensor Power

Projector Signal Cable

Projector Power Cord

Figure 2

Figure 3

Figure 4 Figure 5

52-1/4 in.

Installation (continued)

13. Mount screen onto wall bracket by hooking into

the back groove of the screen frame (Figure 6).

14. Secure bottom of screen to wall using (3) of

the supplied #8 x 1/2” screws through bottom

brackets into the lower channel of the screen

frame (Figure 7).

15. Secure marker tray to right side of screen frame

at desired height by using (2) of the supplied

#8 x 1/2” screws into the side channel of the

screen frame (Figure 8).

16. Secure IR sensor bar (packaged with the S520

Projector) to screen by sliding it onto the metal

bracket. Insert safety screw through IR sensor

bar into bracket (Figure 9).

Figure 6

Figure 8

Figure 7

Figure 9

Attach marker

tray to frame with

(2) screws into the

side channel.

Installation (continued)

Safety

Screw

17. Attach sensor cover by snapping clips over

screen frame. Secure to frame by screwing down

into the upper channel of the screen frame with

supplied #8 x 3/4” screw (Figure 10).

18. In between the projector mount and the IR sensor

cover, cable clips will be mounted to the wall for

cable management. Attach clips to the wall using:

Wood studs: (4) supplied #8 x 1” screws.

Concrete wall or no studs: (4) supplied #8-10

wall anchors and (4) supplied #8 x 1” screws.

When secure, route cables and cords behind the

two cable cover clips. Attach cable cover to the

cable clips (Figure 11).

19. Install projector mount covers and projector.

Refer to the S520 Dual Stud Wall Mount

(MSP-DCCUST1) manual.

Figure 12

Figure 10

Figure 11

Installation (continued)

Recommended Screen/Whiteboard

Markers

This Dell S520 Screen/Whiteboard is a dual-purpose

projection screen and whiteboard. The surface of

the screen/whiteboard can be used with dry erase

markers from a wide variety of manufacturers and

brands. Do not use permanent markers with this

product.

Recommended Screen/Whiteboard

Cleaning

The supplied cleaning cloth can be used to clean

marks on the Dell S520 Screen/Whiteboard surface

made by everyday dry erase marker usage. To clean

persistent marks from dry erase markers, only use

a standard dry erase marker cleaning solution and

the cleaning cloth. To clean permanent marks and

other unintentional marks on the surface, use a non-

abrasive or non-scouring spray cleaning solution with

the cleaning cloth or a melamine foam cleaning pad.

Other manuals for S520

Table of contents

Popular Projector manuals by other brands

iEmmet

iEmmet MP-312 user manual

Epson

Epson VS400 Specifications

Sony

Sony VPL-HS10 Marketing Specifications & Features manual

Sony

Sony VPL-HW65ES Quick reference manual

Toshiba

Toshiba TLP-791U Specifications

Philips

Philips LC1341 Declaration of conformity

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB operating instructions

NEC

NEC NP600S EDU Specifications

BenQ

BenQ SH753P user manual

Eiki

Eiki EK-623U series quick start guide

Epson

Epson PowerLite Pro Cinema 6020UB user guide

Epson

Epson PowerLite Home Cinema 705HD user guide

Christie

Christie LHD700 user manual

Navitar

Navitar FX instruction manual

InFocus

InFocus LitePro 560 user guide

Sony

Sony SRX-R815P operating instructions

Vivitar

Vivitar DP1500 X specification

Acer

Acer C20 Series manual