Dell SE2417HG User manual
SE2417HG 1
1
1. Disassembly Procedures:
Step Figure Remark
S1.Before
disassemble
Turn off power,
Unplug external cables
from product
S2. Remove the
STAND-BASE
ASS’Y
To remove the stand:
Press the button on the
red circle then pull out
the stand follow the
arrow, stand will be
remove.
Note:
To prevent scratches on
the LCD screen while
removing the stand,
ensure that the monitor is
placed on a soft, clean
surface.
SE2417HG 2
S3.Remove the
REAR COVER
Use a Philips-head
screwdriver to remove 2
screws for unlocking
mechanisms.
(No.1~2 screw
size=M3x4;
Torque=4±1kgf.cm)
Use Penknife to separate
the bezel and rear cove
follow the arrows in
sequence, then you can
take out rear cover.
S4.Disconnect the
FFC cable
S5.Remove the
VGA
Use a hex screwdriver to
remove 2 screws for
unlocking mainboard.
(No.1~2 is Hex-screw,
Torque= 4.5±0.5kgf.cm)
1 2
12
SE2417HG 3
3
S6.Remove the
FFC cable
S7.Remove the
PAPER TAPE
and panel FFC
cable
S8.Remove the
MAIN FRAME
Remove and turn over it.
SE2417HG 4
S9.Remove the
MAIN &POWER
BOARD
Use a Philips-head
screwdriver to remove 5
screws for unlocking
main board and power
board
(No.1~4 screw
size=D3x6;
Torque=6±1kgf.cm
No.5 screw size=M4x6;
Torque= 6±1kgf.cm)
Remove the cables
S10.Remove the
KEY BOARD
Use a Philips-head
screwdriver to remove 4
screws for unlocking Key
board.
(No.1~4 screw
size= M2x2.5
Torque=0.9±0.4kgf.cm)
1
3
24
5
1 2 3 4
SE2417HG 5
5
S11.The PANEL
S12.Remove the
screw
Use a Philips-head
screwdriver to remove
1screws for unlocking
main frame
(No.1 screw size= Q3x6
Torque=4±1kgf.cm)
S13.The MAIN
FRAME
S14.The BEZEL
1
SE2417HG 6
S15.Remove
capacitor
Remove electrolyte
capacitors (red mark)
from printed circuit
boards
Take out bulk cap. pin
solder with soldering
iron and absorber
Lift the bulk cap. up and
away from the PCB
SE2417HG 7
7
2. Product material information
The following substances, preparations, or components should be disposed of or recovered
separately from other WEEE in compliance with Article 4 of EU Council Directive 75/442/EEC.
Capacitors / condensers (containing
PCB/PCT)
No used
Mercury containing components No used
Batteries No used
Printed circuit boards (with a surface
greater than 10 square cm)
Product has printed circuit boards (with a
surface greater than 10 square cm)
Component contain toner, ink and liquids No used
Plastic containing BFR No used
Component and waste contain asbestos No used
CRT No used
Component contain CFC, HCFC, HFC
and HC
No used
Gas discharge lamps No used
LCD display > 100 cm2 Product has an LCD greater than 100 cm2
External electric cable Product has external cables
Component contain refractory ceramic
fibers
No used
Component contain radio-active
substances
No used
Electrolyte capacitors (height
> 25mm, diameter > 25mm)
Product has electrolyte capacitors
(height > 25mm, diameter > 25mm)
3. Tools Required
Listthetypeandsizeofthetoolsthatwouldtypicallycanbeusedtodisassembletheproducttoapoint
wherecomponentsandmaterialsrequiringselectivetreatmentcanberemoved.
ToolDescription:
‐PhillipheadScrewdriver
‐HexScrewdriver
‐Penknife
‐Solderingironandabsorber
Other manuals for SE2417HG
2
Table of contents
Other Dell Monitor manuals
Dell
Dell U2520DR User manual
Dell
Dell S2340T Touch Parts list manual
Dell
Dell IN2010N User manual
Dell
Dell S2209W - 21.5" LCD Monitor User manual
Dell
Dell SR2320L User manual
Dell
Dell P3221D User manual
Dell
Dell S3422DW User manual
Dell
Dell UltraSharp 25 Series User manual
Dell
Dell D7532QT User manual
Dell
Dell P2722HE User manual
Dell
Dell P2011H User manual
Dell
Dell SE178WFPC User manual
Dell
Dell P1913 User instructions
Dell
Dell UltraSharp 1704FPT User instructions
Dell
Dell E177FP - 17" LCD Monitor User manual
Dell
Dell D3217H User manual
Dell
Dell P992 User manual
Dell
Dell P3421W User manual
Dell
Dell E2222H User manual
Dell
Dell UltraSharp U2417HA User manual
