Dell P2217 User manual
Product Announcement:
This product is certificated to meet RoHS
Directive and Lead-Free produced definition.
Using approved critical components only is
recommended when the situation to replace
defective parts. Vender assumes no liability
express or implied, arising out of any unauthorized
modification of design or replacing non-RoHS
parts. Service providers assume all liability.
Qualified Repairability:
Proper service and repair is important to the safe,
reliable operation of all series products. The
service providers recommended by vender should
be aware of notices listed in this service manual in
order to minimize the risk of personal injury when
perform service procedures. Furthermore, the
possible existed improper repairing method may
damage equipment or products. It is recommended
that service engineers should have repairing
knowledge, experience, as well as appropriate
product training per new model before performing
the service procedures.
NOTICE:
! To avoid electrical shocks, the products should be
connected to an authorized power cord, and turn
off the master power switch each time before
removing the AC power cord.
! To prevent the product away from water or
expose in extremely high humility environment.
! To ensure the continued reliability of this
product, use only original manufacturer’s
specified parts.
! To ensure following safety repairing behavior, put
the replaced part on the components side of
PWBA, not solder side.
! To ensure using a proper screwdriver, follow the
torque and force listed in assembly and
disassembly procedures to unscrew screws.
! Using Lead-Free solder to well mounted the
parts.
! The fusion point of Lead-Free solder requested in
the degree of 220°C.
1. Important Safety Notice
2. Exploded view diagram with list of items
3. Wiring Connectivity Diagram
PANEL
CRT1
HDMI1DP1
Power board
KB1
FK BD
USB Side Board
USB1 USB2 USB3
Interface board
4. Disassembly and Assembly Procedures
S2
4.1 Disassembly Procedures:
S1
S3
S6
S5
S4
Remove the monitor stand base:
1. Place the monitor on a soft cloth or cushion.
2. Press and hold the stand-release button.
3. Lift the stand up and away from the monitor.
Use a Philips-head screwdriver to remove 4pcs
screws for unlocking mechanisms. Remove DP cap.
(No.1~4 screw size=M4x10; Torque=12±0.5kgfxcm)
2
3
Turn over the LCD monitor to let the screen faced
up, place a cloth on the panel where you are working
on to protect the panel. Continually, then wedge your
fingers between the front bezel and the panel for
unlocking mechanisms.
Turn over the LCD monitor to let the screen faced
down and then turn on the rear cover carefully.
Disconnect the USB FFC cable from the connector
of the interface board, and then remove the rear
cover.
1
top side
bottom side
2
2
3
23
41
Tear off two pieces of the aluminium foils and PVC
tape for unfixing the bracket chassis base.
Use a proper tool to release the function key cable
from the connector, then pull the function key cable
high for unsticking two positions with glue and
release the function key cable.
Use a Philips-head screwdriver to remove one screw
for unlocking the USB board unit, then release the
USB board unit and put it aside.
(No.1 screw size=M3x6, Torque=4±0.5kgfxcm)
aluminium foil
1
S7
Necessary repair and test equipment:
1. Philips-head screwdriver
2. Hex-head screwdriver
4. Disassembly and Assembly Procedures
S9
S11
S12
S8
Unplug the panel power cable from the connector of
the panel module, then release the cable from the
panel by tearing off the adhesive tape.
Move up the bracket chassis module , tear off the
adhesive tape for release the LVDS cable, then push
the ear lock, and remove the LVDS cables from the
connectors of LCD panel module.
Take away the and then put
the bracket chassis module on a protective cushion.
bracket chassis module
(Note: you must stick a piece of mylar when you
change a new panel.)
Lift up the panel module with the bracket for
removing the front bezel with function key board,
and then release the function key board from the
hooks of the front bezel. Put the panel with bracket
chassis on a protect cushion.
S13
S10
Use a Hex-head screwdriver to remove two screws
for unlocking the D-Sub connector.
(No.1~2 screws size=M3x8, Torque=6±0.5kgfxcm)
( No.3~4 screw size=M3x8, Torque=6~7kgfxcm)
Use a Philips-head screwdriver to remove
screws for unlocking the AC power outlet.
two
Turn over the bracket chassis. Use a Philips-head
screwdriver to remove six screws for unlocking the
circuit board, release all the cables from the hooks.
(No.1 screw size=M4x8, Torque=6±0.5kgfxcm;
No.2~6 screw size=M3x7.5, Torque=6±0.5kgfxcm)
1
2
3
56
4
21
43
4. Disassembly and Assembly Procedures
Remove the interface board and power board from
the bracket chassis module carefully, and disconnect
all the cables.
S14
4. Disassembly and Assembly Procedures
4.2 Assembly Procedures: Turn over the bracket chassis module.
Use a Philips-head screwdriver to tighten two screws
for locking the AC power outlet.
Use a Hex-
head screwdriver to tighten two Hex Nuts for locking
the D-Sub connector.
(No.1~2 screw size=M3x8, Torque=6±0.5kgfxcm)
(No.3~4 screw size=M3x8, Torque=6~7kgfxcm;
S6
S5
Panel preparation: Examine the panel surface
according to inspection criteria. Turn over the panel
to place the screen faced down, then Use a Jp to
stick a piece of mylar on the specific position as the
picture below shown.(Note: you must stick a piece of
mylar when you change a new panel.)
S7
mylar
21
43
Turn over a power board and put the power board
into the bracket chassis, locate the panel power
cable into the hook of the bracket chassis.
Place a bracket chassis base on a protective
cushion.
S2
S1
Take a interface board, connect a LVDS cable to the
connector of the interface board, then connect the
cable of the power board to CN2202 of the interface
board. Turn over the interface board and locate it into
the bracket. Use a Philips-head screwdriver to tighten
six screws for locking the power board and interface
board.
(No.1 screw size=M4x8, Torque=6±0.5kgfxcm;
No.2~6 screw size=M3x7.5, Torque=6±0.5kgfxcm)
3
Cn2202
2
S3
1
65
Put the bracket chassis module on the back of LCD
module.
4
4. Disassembly and Assembly Procedures
S10
Put the panel module with the bracket into the front
bezel carefully to avoid pressing the function key
cable, then adjust position of the bracket chassis
module till the both parts firmly attached.
Push the earing-lock, connect LVDS cable to the
connector of panel module, then fix the cable with
the double-faced tape which sticked on the back of
the cable.
S11
S12
Use a proper tool to connect the function key cable
to the connector of the board. Fix the function key
cable by two adhesive tapes which taped on the
back of the cable as the positions of No.1 2.~
Connect the panel power cable to the connector of
the panel module, then tear off the adhesive tape
which sticked on the back of cable, fix the cable to
the panel.
12
Use a Jip to fix the bracket chassis base module and
panel module, then stick two pieces of aluminium foil
to fix the bracket chassis base on the positions of
the panel as the picture below shown.
aluminum foil
S13
S8
S9
aluminum foil
Take a function key board and a front bezel, then
locate the function keyboard into the hooks of the
front bezel for the two parts firmly attached as the
picture below shown. Put the front bezel on a protect
cushion for later assembling.
Take a USB board, a USB hub and a connect cable.
Connect the cable to the USB board, then locate the
USB board into the USB hub.
S14
4. Disassembly and Assembly Procedures
Use a Philips-head screwdriver to tighten four
screws for locking mechanisms, then
.
stick one
piece of label on the specific positions as the
picture below shown
(No.1~4 screw size=M4x10; Torque=12 0.5kgfxcm)±
Move the assembled rear cover close to the
panel unit, then connect the USB FFC cable to
the connector of interface board. Put down the
rear cover and push the rear cover on the
positions marked as the picture below shown for
mechanisms engagement.
S17
S16
Put down a rear cover on a protect cushion. Stick
a piece of aluminum foil on one side of the USB
hub, then locate the USB unit into the hook of the
rear cover, then use a Philips-head screwdriver to
tighten one screw for locking the USB board with the
USB hub with the middle bezel.
(No.1 screw size=M3x6, Torque=4±0.5kgfxcm)
S15
23
41
L c
rovide power supply
and a video signal to the monitor
ift up the monitor, heck the DELL logo if it is firmly
attached to the front bezel. P
, then turn on the
monitor for functionality check.
S19
Stick one piece of label on the specific positions as
the picture below shown. Fit the two tabs on the
upper part of the stand into the grooves on the back
of the monitor, and then press the stand so that the
monitor mounting area snaps onto the stand.
S18
1
5. Trouble Shooting Instructions
WARNING: Before you begin any of the procedures in this section, follow the
Safety instructions.
Self-test
Your monitor provides a self-test feature that allows you to check if your monitor is
functioning properly. If your monitor and computer are properly connected but the
monitor screen remains dark, run the monitor self-test by performing the following
steps:
1. Turn off both your computer and the monitor.
2. Disconnect all video cables from the monitor. This way, the computer doesn’t
have to be involved.
3. Turn on the monitor.
If the monitor is working correctly, it detects that there is no signal and one of the
following message appears. While in self-test mode, the power LED remains white.
Dell
P1917S/P1917SWh
No VGA Cable
The display will go into Power Save Mode in 4 minutes.
www.dell.com/support/monitors
?
Dell
P2017H
No VGA Cable
The display will go into Power Save Mode in 4 minutes.
www.dell.com/support/monitors
?
Dell P2217/P2217Wh
No VGA Cable
The display will go into Power Save Mode in 4 minutes.
www.dell.com/support/monitors
?
Table of contents
Other Dell Monitor manuals
Dell
Dell E198WFP User manual
Dell
Dell 320-7459 - S1909WXF - 19" LCD Monitor User manual
Dell
Dell P2424HT User manual
Dell
Dell P2721Q User manual
Dell
Dell E177FP - 17" LCD Monitor User manual
Dell
Dell E178FPC User manual
Dell
Dell AW2721DB Instructions for use
Dell
Dell C3422WE User manual
Dell
Dell M783c User manual
Dell
Dell U3014 User manual
Dell
Dell UltraScan P1110 Specification sheet
Dell
Dell P170ST User manual
Dell
Dell P3421WB Instructions for use
Dell
Dell UltraSharp 2007WFP User manual
Dell
Dell E1911 Specification sheet
Dell
Dell P2010H User manual
Dell
Dell E2016HV Instructions for use
Dell
Dell SE198WFP - 19" LCD Monitor User manual
Dell
Dell Alienware AW2518H User manual
Dell
Dell E2222H Instructions for use
