DEL TIXIT Owner's manual
TIXIT
AUTOMATIC ABOVE-GROUND COVER
TECHNICAL INSTRUCTIONS Installation / Use / Cleaning / Maintenance / Safety advice
2
Maximum pool size:
Length: 13.5 m
Width: 5 m
information
NOTICE TO BE GIVEN TO THE USER AFTER INSTALLATION IS COMPLETE
PLEASE READ CAREFULLY AND KEEP IN A SAFE PLACE.
At the time of publication, covers with an overlap and covers with removable steps
on the side are not compliant with standard NF P 90-308.
Unless otherwise specified by the manufacturer, immersion alarms are not compatible
with DEL automatic covers.
Automatic motorised above ground safety cover using either mains electricity or solar power.
The opening or closure operation requires about 2 minutes for one person and about 3 minutes
to lock or unlock the attachment kits.
3
a
b
c
information
-The motor (compliant with electric standards) is located in the tube and can
be accessed from the exterior of the terminal.
- Adjustment of the “mechanical automatic stop” locking the cover in place once
it has been fully unrolled or rolled, is done
directly on the motor.
- Solar version: The solar panel and batteries are built into the tube fitted.
- Electric version: The electrical control box is fitted in a technical room close to
the pool. (see page 6 for the box size)
Slats:
- The cover itself is made from unleaded PVC slats (this material conforms to
anti-ageing requirements as defined in the NF T 54 405-1 Standard), they are
watertight and hinged and will float on the surface of the water.
- The gap between the side and the cover must be <= 70 mm.
- The cover is connected to the tube using white straps that are attached to the
first slat of the cover.
- There are fixture straps at the start and end of the cover used to fix the cover
to the fastening kit fixed to the side of the pool.
Fastening kits:
3 models: (a - Push-lock / b - Quick-lock / c - Straplock)
3 fixture modes: (surface mount – insert mount – hanging mount)
- The fastening kits are positioned on each width of the pool.
(the number varies depending on the pool configuration)
- These fastening systems are triggered by a tool or a double action.
Optional:
- “Chlorinator coupling” (electric version only):
Connected to the roller and chlorinator control box, this option is used
to automatically reduce chlorine production when the pool is closed in order
to avoid excess chlorine in the water.
The roller:
32 cm at the shaft
- “Torque limter”:
Printed circuit board with stops motion when an abnormal force on the cover is
detected. (unlocking of locking kit oversight)
Cover control:
- Wi-Key “wireless”
Or
- Key switch
4
x1 x1
x2
x1
x6 x8 x4
x6 x6
x2 x2 x2
x1
x1
M8 12x60
M8x80
M8
M6
3x16
x4
M6
x12
M4x10
x4
M8
M8x30
x2
DELIVERED PARTS
or or
OPTION - CHLORINE INHIBITOR OPTION - Automatic switch
or
Description
Option Wi-Key
5
Ø8 - 12
PACKING LIST
e.g. - for a 4 x 8 m pool
Total weight: 205 Kg
TOOLS
ASSEMBLY INSTRUCTIONS
3 hours
Description
6
6 cm
34 cm
24 cm
Alimentation 230 V
Electrolyseur
(U1000RO2V sous gaine)
selon la norme en vigeur
LED
30 cm
mini
LED
Installation
Remember to have a sheath
fitted to connect the electric
control box and the motor
terminal.
D + 6 cm
see positioning
rules 1
page 8
D = (measurement between the
terminal - pool width) / 2
ELECTRIC version
SOLAR version
Place the solar panel on the
sunniest side
Instructions before installation
x2
7
x2 x2 x4
Vis THEF
M8x30 écrou M8
x1 x1
ASSEMBLY / POSITIONING / FIXTURE
Installation
Assembly
motor side
8
=
=
Installation
Position 2
centre of the width
With
Straplock
or
Push-lock
With
Quick-lock
Position 1
Depending on the pool corners and the fastener kits on the roller side
Sharp corner Rounded corners or cut-off corners
Min. = 15 cm
Min. = 15 cm
Max. = 60 cm
Max. = 60 cm
9
Ø12
x2
M8 12x60
M8x80
M8
3x16
Installation
Fixture and adjustment
Ø12
Fix the adjustment bar.
motor side
Levelling
10
10
M6
M6
x4 x4
x8
1
2
Installation
ASSEMBLING THE MOTOR
Make small rotating
movements with the motor
to ease its fitting.
Table of contents
Other DEL Swimming Pool manuals
