DAPAudio EM-7.2 Operation manual
i
PRO'FssIONAL 5TEREO MIXER
E M-7 .2 / EM-5 1 / E f'A-7 .3
Please read before using this equipment
@. Pl.,g, ;E; I r[o[F
999199999991
x' qÆroloçDooo"Q.o | -
@" eô. Ë_Ë ë
T 1P T ,**,
0 | r0 J2 i+12 424+12 -124+12
UNR Lrfl Ê
@^@*
r.rt
"@ ofo d
E::'Ë::"'(.Ç
oo\=
lqôlô.rl
l@ @l@ @l
o@
-o
@@
o
@@
o
@
ô
@lô ôl
ool
ol@ @l
o@
@ ô'u
10 o l{
I .12-+12 .12 -+12 I
ooolooooooo I
X' q$oloç"ooo"e,o I
u @O Orr
o@Ë
::-@
tô ôt
lo"o I
@
"@ .f
E::."Ë
oo
tôô
lo'o
râ\
@O .,t"
o ot
ol6 ôlô ô
olo'o lo"o
o@ @
Front panel
1. POWER.LED
Lights up when the mixer's power is on.
2. MrC 1&2-SOCKET
You can connect microphones with XLR-plug and control the signals via the Mic Level-control.
3. ZONE.SELECT.BUTTONS
Route the channel signal to zone 1,2 & 3.
4. MIC LEVEL.CONTROL
With the MIC LEVEL-control, you can adjust the microphone volume.
5. MIC BASS.CONTROL
Used to increase or lower the LOWs of the input signal.
6. MIC MIDDLE.CONTROL
Used to increase or lower the MlDs of the input signal.
7. TREBLE.CONTROL
Used to increase or lower the Hls of the input signal.
8. MIC MUTE.BUTTON
This switch turns the corresponding signal of the Microphone channel on or mute
9. MIC PEAK LED
The Peak LED illuminates when Mic's signal is going into overload.
10. TALKOVER DB.CONTROL
Used to adjust the attenuation.
1 1. TALKOVER TIME.CONTROL
Used to adjust the response time.
12. TALKOVER.BUTTON
Press this button if you want to use your microphone. When the button is pressed, all signals but the microphone level
are attenuated by 15 dB.
13. CHANNEL.FADER
Used to adjust the input level of each channel.
14. CUE-BUTTON
Use the CUE-button in order to select the channel(s) to be monitored.
15. PHONO / LINE.SWITCH
Used to select the input to be sent to the individual channel.
16. CHANNEL PEAK LED
The Peak LED illuminates when channel's signal is going into overload.
1 7. ZON E.SELECT.BUTTONS
Route the channel signal to zone 1,2 & 3.
1 8. OUTPUT LEVEL.CONTROL
With the OUTPUT LEVEL-control, you can adjust the output level of the individual channel.
1 9. MASTER.BASS.CONTROL
Used to increase or lower the LOWs of the output signal.
20. MASTER MIDDLE.CONTROL
Used to increase or lower the MlDs of the output signal.
21. MASTER.TREBLE.CONTROL
Used to increase or lower the Hls of the output signal.
22. CHANNEL DISPLAY
The display shows the individual channel signal.
23. PHONE LEVEL.CONTROL
With the Level-control, you can adjust the phones volume without changing the output signal.
24. HEADPHONES.SOCKET
Use this socket to connect the headphones. Headphones from 8 Ohms to 600 Ohms can be used.
25. CUE MIXING.FADER
Connect your headphones to the HEADPHONES socket. With the CUE-buttons, you can select the desired channel.
When you set the CUE MIXINc-fader to PGM (CUE-buttons without function), you can cue the output signal of the
mixer. When you set the CUE MIXING-fader to the center position, you can cue both the channel-signal you selected
and the output-signal.
26. REC SELECT
For selecting the channel routed to the Master signal.
27. REC OUT
To connect your recording unit.
28. CUE MODE BUTTON (CUE SPL|T/CUE MIX BUTTON)
Cue Split-function (button pressed and): the Cue-signal is on the one side of the headphones and the output-signal on
the other side.
Cue Mix-function (button released): the adjustable mix of Cue-signal and output-signal is on both sides of the
headphones.
29. BOOTH.CONTROL
The mixer features a DJ BOOTH monitor system. Connect your monitor system with the BOOTH-sockets on the rear
panel.
30. LINE INPUT LEVEL.CONTROL
With the LEVEL-control, you can adjust the input level.
31. LINE INPUT.SOCKETS
Connect CD-player or Tape Deck with LINE input-socket.
32. REC NO MtC
Rear panel
1. POWER SWITCH
Press this button to start operating.
2. AC CONNECTION
Plug the power supply cable in here.
3. REC OUT
To connect your recording unit.
4. BALANCED MASTER OUT
Balanced output for the master signal.
5. MASTER OUT
Output sockets for connecting your power amplifier.
6. LINE INPUT.SOCKETS
Connect CD-players or Tape Decks connected with LINE input-sockets. Line level musical instruments with stereo
outputs such as Rhythm Machines or Samplers should also be connected with the LINE input-sockets.
7. PHONO INPUT.SOCKETS
Connect your turntable with the PHONO input-sockets.
8. REC WITH MIC/NO MIC
9. TRIM CONTROL
For pre-adjusting the input signal.
10. GND (Ground terminal)
Connect the ground lead of the turntable with this terminal. This helps to reduce humming and pop noises.
11. PHONO/LINE.SELECTOR
These switches select between the rear-panel Phono(RIAA) and Line inputs.
12. MtC 1&2€OCKET
You can connect microphones with XLR-plug and control the signals via the Mic Level-control.
13. Output Voltage Selector
The output voltage selector allows the unit to output signal either 0.75V or 1.5V
1 4. STEREO/MONO.SWITCH
Used to set the master output to mono or stereo. lf you connected a mono-signal via 1 RCA-socket, you can switch the
output signal to STEREO in order to have a stereo output signal.
15. BOOTH
Connect your monitor system with the BOOTH-sockets on the rear panel.
l0
This manual suits for next models
2
Other DAPAudio Music Mixer manuals
DAPAudio
DAPAudio Core Mix-3 USB User manual
DAPAudio
DAPAudio Core Mix-2 USB User manual
DAPAudio
DAPAudio Sessionmix 8 User manual
DAPAudio
DAPAudio Oxygen User manual
DAPAudio
DAPAudio Core Mix-4 USB User manual
DAPAudio
DAPAudio DS-CDJ-250 MKII User manual
DAPAudio
DAPAudio Sessionmix 6 User manual
DAPAudio
DAPAudio Core Beat V2 User manual
DAPAudio
DAPAudio IMIX-7.2 USB User manual
DAPAudio
DAPAudio IM-53 User manual
DAPAudio
DAPAudio Core Club User manual
DAPAudio
DAPAudio Compact 8.1 User manual
DAPAudio
DAPAudio GIG-164CFX User manual
DAPAudio
DAPAudio Platinum User manual
DAPAudio
DAPAudio Compact 6.2 D2320 User manual
DAPAudio
DAPAudio GIG-1000CFX User manual
DAPAudio
DAPAudio Core Beat User manual
DAPAudio
DAPAudio GIG-124CFX User manual
DAPAudio
DAPAudio PMM-401 User manual
DAPAudio
DAPAudio MMIX-4 User manual
