Daniamant Dan WR3 User manual
WR3 Instruction Issue 08 (D0613)
Description
The Dan WR3 is a flashing lifejacket light which is activated by a water sensor or
manually using the on/off button.
The recessed holding clips require special tool for assembly and are designed to
be fitted by the life jacket manufacturer.
Daniamant A/S
Industrivej 24C
DK-3550, Slangerup, Denmark
Tel: +45 47 37 38 00 Fax: +45 47 37 38 09
www.daniamant.com
www.daniamant.com
M2-INST Issue 1 (CXXXX)
Dan WR3 lifejacket light
Installation and Maintenance Instructions
2
Installation
The Dan WR3 is for use on solid foam, easy to don lifejackets only. The
recessed Clip may be fitted only by the lifejacket manufacturer, as specialised
cutting tools are required; the light may be changed by anybody.
New Clip (new jackets), part no.1953 for standard blue clip for other colours contact
orders@daniamant.com.
It is the responsibility of the lifejacket manufacturer to ensure that the light is
attached securely and is in the correct position on the lifejacket to provide
maximum visibility when the wearer is in the water.
Retrofit
The Dan WR3 can also be fitted to lifejackets previously fitted with model Dan
WR2. The original clip for the Dan WR2 must be removed and the replacement
clip fitted.
Clip for replacements (old jackets originally fitted with DAN WR2), part no. 1954 for the standard blue
clip, for other colours contact orders@daniamant.com
3
Operation
The DAN WR3 is switched on automatically when the sensor is immersed in
water, and can be switched off by pressing the on/off button *for one second.
The light can also be activated and deactivated manually by pressing the on/off
button*.
Figure depicts the Sensor Switch and the Manual ON/OFF Button
Maintenance
Routine service
Dan WR3 is maintenance free, but the following checks must be made annually:
1. Inspect the light for signs of damage or corrosion.
2. Press the on/off button for one second and the light will commence
flashing then press the button* once more and the light should deactivate.
3. To test the Sensor Switch –a paper clip may be applied to the 2 water
contacts. It is recommended that the light is activated for 1 minute.
Replacement
The Dan WR3 lifejacket lights have a storage life of 5 years and must be replaced
by the date shown on the label.
Health and safety information
Dan WR3 lights contain Lithium cells. These must be handled correctly:
•Do not dismantle the light assembly
•Do not make any external electrical connection
•Do not recharge
•Do not incinerate
Store between -30°C and +65°C
ON/OFF
Button
Sensor
Switch
4
The Batteries are hermetically sealed pressurised primary Lithium/Manganese
cells, and as supplied are electrically protected by a solid state device, and are
environmentally protected by a moulded plastic housing. In this condition the units
pose no definable hazard to health.
Information on the composition and behaviour of these products is contained in
the Product Safety Data Sheet, available from our website
(www.daniamant.com) or on request.
Disposal
Dispose of used and expired lights in accordance with local regulations. This
could be done through an approved environmental disposal agent.
All Daniamant product disposal instructions are available within the user instruction leaflet provided with the
product, or alternatively, available for download on this website.
Daniamant’s Survivor Location Lights contain batteries as well as electrical and electronic components, and
must therefore be segregated from the domestic waste stream and recycled. Disposing of this product
correctly will help save valuable resources and prevent any potential negative effects on human health and
the environment, which could otherwise arise from inappropriate waste handling. Daniamant’s lights are
marked with the symbol below which conveys that this waste must be treated separately from household
waste.
To ensure compliance with the WEEE and Battery Regulations, the Survivor Location Lights placed on the
market in the UK or Denmark should be returned to Daniamant in the UK or Denmark, or deposited in your
nearest WEEE Designated Collection Facility, operated by your Local Authority.
Further copies of this installation and maintenance instructions are available to download from
our website www.daniamant.com
A copy of these instructions must be held with the ships/owners training manual.
Table of contents
Other Daniamant Lighting Equipment manuals
Daniamant
Daniamant SL-450 User manual
Daniamant
Daniamant Dan WL3 User manual
Daniamant
Daniamant ODEO FLARE Operation manual
Daniamant
Daniamant Dan M3 User manual
Daniamant
Daniamant L90 User manual
Daniamant
Daniamant SL-400 User manual
Daniamant
Daniamant Dan W3-1 User manual
Daniamant
Daniamant L7A User manual
Daniamant
Daniamant RL1 User manual
Daniamant
Daniamant SL-500 User manual
Popular Lighting Equipment manuals by other brands
Qazqa
Qazqa Suplux SL 3 Black 103062 instruction manual
Commercial Electric
Commercial Electric 54568141 Use and care guide
CREE LIGHTING
CREE LIGHTING 304 Series installation instructions
Goobay
Goobay 49867 user manual
ECOMAN ITALIA
ECOMAN ITALIA LED T8 instruction manual
Alkalite
Alkalite Krypton KT-81 user manual
