Danfoss TS715 Si Assembly Instructions
TS715
Installation & User Instructions
single channel
timeswitch
2
INDEX
Index
Installation
Product specification 3
Installation 4
Wiring 5
DIL switch settings 5
Wiring Conversion 6-9
User
Your timeswitch 10
Preset programmes 10
Before you start 11
AM/PM or 24hr display 11
Setting the Time and Day 11-12
Accepting the preset programmes 12
Changing the preset programmes 13
Programming system - 5/2 day 14-15
Programming system - 7 day 16-17
Programming system - 24 hour 18
Running the programme 19
Temporary overrides 20
Changing clocks forward/back 21
Troubleshooting 22
Contact details 24
+1HR override
MAN override
RESET
Mode
SELECT
+1HR
MAN
3
Please Note:
This product should only be installed by a
qualified electrician or competent heating installer,
and should be in accordance with the current
edition of the IEEE wiring regulations.
Specification
Power supply 230 Vac, ±15%, 50/60 Hz
Switching action
1 x SPDT voltage free, Type 1B
Switch rating Max 264 Vac, 3(1)A
Battery back-up 24 hours minimum
Setting/Running Accuracy ±1 minute
Dimensions, mm (W, H, D) 135 x 88 x 32
Design standard EN 60730-2-7
Control Pollution Situation Degree 2
Rated Impulse Voltage 2.5kV
Ball Pressure Test 75°C
Product specification
Installation & Specification
Installation Instructions
4
Installation
Remove wallplate from unit by unscrewing the two
screws on the bottom edge of the unit.
From the top left hand corner of the wallplate, there
must be clearances of at least 140 mm to the right,
15mm to the left, 30mm above and 100mm below in
order to mount the plug-on module.
The wallplate must be securely mounted either
directly to the wall using suitable wood screws or to a
flush mounted 1-gang electrical accessory box using
M3.5 screws.
Cable access can either be from behind for
concealed cabling, or from below for surface cabling.
If surface cable is used, cut out cable access slot on
plug-on module prior to mounting the module.
For wiring connections refer to diagram on page 5.
TS715 models are double insulated and do not
require an earth connection, however a parking
terminal is provided on the wallplate. This is clearly
marked with an Earth symbol.
Prior to mounting the plug-on module, DIL switches
on the rear of the plug-on module must be set. See
diagram on page 5 for available options.
Mount plug-on module to wallplate by locating tabs
on top of wallplate in apertures on rear of module,
hinge down and press firmly to wallplate before
tightening securing screws on bottom of wallplate.
Installation
5
Wiring
COM OFF ON
Mains
fused
3A
TS715 (3066 12/01)
Wiring & DIL switch settings
Always switch off mains first and never fit
programmer to a live wallplate.
For Wiring Conversion tables see pages 6-9
NOTE:
Link terminals
L and 1 for
standard mains
voltage operated
systems
Remember to tick the
INSTALLER SETTING box on
the inside flap label to notify
user in which
mode their unit
is set (24hr, 5/2
day or 7 day).
DIL Switch Settings
2 ON/OFFs
2 ON/OFFs
7 DAY or 24 HOUR
24 HOUR
3 ON/OFFs
3 ON/OFFs
5/2 DAY
7 DAY
SW.1
SW.2
SW.3
SW.4
Before mounting the unit, ensure
the 4 DIL switches on the rear of
the unit have been moved to the
required settings !
INSTALLER SETTING
24 Hour
5+2 Day
7 Day
6
DANFOSS RANDALL
TS715
MAINS
NL
NL
The existing wallplate may be used when replacing the following, but the wiring m
u
wire link between L & COM terminals of wallplate.
ACL LS111, LS711, LP111 & LP711 N L
DRAYTON TEMPUS ONE & TEMPUS TWO N L
LANDIS & GYR RWB3 N L
LANDIS & GYR RWB30 N L
The TS75/TS15 wallplate must be used to replace the existing wallplate when repl
a
mains voltage systems, fit wire link between terminal 1 & L of wallplate.
GRASSLIN 45, 45A, 45E 2 1
HONEYWELL ST6100 N L
HORSTMANN 423 PEARL, EMERALD & TOPAZ N L
HORSTMANN KMK2A YMK2 3 4
HORSTMANN 425 CORONET N L
DANFOSS RANDALL 911 N L
DANFOSS RANDALL 103, 103E, 103E5 & 103E7 5 6
RANDALL 3020 1,7 6
DANFOSS RANDALL SET1 N L
RANDALL TSR2 3 2
PEGLER SUNVIC SP20 & SP25/30 N L
POTTERTON MYSON EP4001 N L
WIRING CONVERSIONS
Wiring conversions for other timeswitches which can be replaced with the
Danfoss TS715, refer to the second part of the table. If in any doubt, please
contact our Technical Services Department before proceeding with the
replacement.
7
LOAD An additional terminal block may be required
where these disconnected leadss (or pairs of
leads) should be terminated
COM OFF SPARE ON
12 3 4 AB CD
u
st be reconnected as shown below. In addition, in mains voltage systems, fit
12 4 3
13 4 2
-3 1 4 2
23 1 4
a
cing the following timeswitches. Wiring details are shown below. In addition, in
3- 4
12 3 4 - -
3- 1 4 25 6
1- 2
56 1 4 2 3
54 2 6
3- 2 1
-- 2 4 35
56 2 4
1- 4 5 67
34 S 5
52 4 AB C D
8
DANFOSS RANDALL
TS715
MAINS
NL
NL
The TS75/TS15 wallplate must be used to replace the existing wallplate when repl
a
mains voltage systems, fit wire link between terminal 1 & L of wallplate.
SANGAMO M6 4,5 6
SANGAMO 410 FORM 8 4,5 3
SANGAMO S254 FORM 2, S408 FORM 5,
S251 FORM 2 NL
SANGAMO S610 FORM 2, S611 FORM 2,
S612 FORM 2, S408 FORM 4, S408 FORM 6,
S253 FORM 2, S255 FORM 2
NMOTOR
LIVE
SANGAMO S409 FORM 8 3,N 3,L
SANGAMO S263 FORM 2
SANGAMO S264 FORM 2 NL
SMITHS IND. MKI, MKII N L
SMITHS IND. CENTROLLER 30 1 2
SMITHS IND. CENTROLLER 40 1 2
SWITCHMASTER N L
TOWERCHRON TC 2 1
VENNER VENNERETTE MKIIA N L
VENNER VENNERETTE MKIVA 2 3
VENNER VENOTIME (WITH NEON INDICATING
CIRCUIT ON) NL
VENNER VENOTIME (WITH NEON INDICATING
POWER ON) NL
VENNER VENNERON, VENNERON P 3 2
9
LOAD An additional terminal block may be required
where these disconnected leadss (or pairs of
leads) should be terminated
COM OFF SPARE ON
12 3 4 ABCD
a
cing the following timeswitches. Wiring details are shown below. In addition, in
32 7 1 8
-2 6 1 78
-- LOAD
SWITCH
LIVE -LOAD
6- 1 2
-OFF ON
P2 - P1 P3
-- 3 4,56
-- 3 4,5
4- 2 1 3
4- 3 7 891011
LINE - LOAD
4- 1
-1 2 3
21 3
1- 4
10
User Instructions
Your timeswitch
The TS715 allows you to switch your system on and off at
times that suit you.
You can programme up to 3 ON/OFF times per day, which
will come on and go off at the same times.
Preset Programmes
Your TS715 comes ready programmed with a set of
operating times which often suit most people.
If you want to change any of these settings, you can do so
by following the instructions on pages 13-18. First, follow
the steps on page 11-12 to set the correct time and date.
Overview & Preset Programmes
Event No. Hot Water &
Heating Mon-Fri Sat-Sun**
1 1st ON 6:30 7:30
2 1st OFF 8:30 10:00
3* 2nd ON* 12:00* 12:00*
4* 2nd OFF* 12:00* 12:00*
5 3rd ON 17:00 17:00
6 3rd OFF 22:30 22:30
* Not applicable if unit set to 2 ON/OFFs per day by installer
**Not applicable if unit set to 24 hour mode by installer
See page 13 for explanations of different settings
Other manuals for TS715 Si
4
Table of contents
Other Danfoss Switch manuals
Danfoss
Danfoss RT 1AE User manual
Danfoss
Danfoss KP 15 User manual
Danfoss
Danfoss RT 30AW User manual
Danfoss
Danfoss RT 6W User manual
Danfoss
Danfoss KPU Series User manual
Danfoss
Danfoss LLS 4000 User manual
Danfoss
Danfoss KPS 35 User manual
Danfoss
Danfoss RT 112 User manual
Danfoss
Danfoss KPU 1 User manual
Danfoss
Danfoss KPU Series User manual
Danfoss
Danfoss KP 34 User manual
Danfoss
Danfoss AMV 410 User manual
Danfoss
Danfoss LLS 4000 Installation and maintenance instructions
Danfoss
Danfoss RT 6AEW User manual
Danfoss
Danfoss KP 1E User manual
Danfoss
Danfoss KP 21 User manual
Danfoss
Danfoss AKS 38 User manual
Danfoss
Danfoss CWH1000 Manual
Danfoss
Danfoss KPI 34 User manual
Danfoss
Danfoss KP 15 User manual
