Dake CUT 250 COLD SAW User manual
CUT 250 COLD SAW
7/13/05 1
MANUAL FOR 250 COLD SAW
MODEL
:
:
________________________________________
SERIAL NUMBER:
________________________________
DATE PURCHASED:
______________________________
DAKE Division of JSJ
724 Robbins Road
Grand Haven, Michigan 49417
616-842-7110 Phone 800-937-3253
616-842-0859 Fax 800-846-3253
Web: www.dakecorp.com
Email: customerservice@dakecorp.com
CUT 250 COLD SAW
7/13/05 2
Accident prevention
Regulations
-This machine has been built to comply with national accident prevention regulations. Improper
use and/or tampering with the safety devices will relieve the manufacturer of all responsibility.
-Check that the voltage indicated on the plate, normally fixed to the machine motor is the same as
the line voltage.
-Check the efficiency of your electric supply making sure the machine has it’s own grounded
circuit.
-Do not operate machine without safety guards or with the electrical panel cover removed.
-Always disconnect machine from power source before changing the blade, performing
maintenance or if the machine is operating abnormally.
-Do not operate this machine without the handle and/or handle switch disconnected.
-Always wear OSHA approved safety glasses when operating this machine.
-Never put your hands or arms into the cutting area while the machine is in operation.
-Do not shift or move machine while the machine is in operation.
-Do not wear loose clothing, gloves, bracelets, rings, watches, chains or any other object
that could get caught in the machine while in operation and Tie back long hair.
-Keep the machine bed free from tools or any other object, while machine is in operation.
CUT 250 COLD SAW
7/13/05 3
Location of safety
Covers
-Grey metal shield covering the blade.
-Blue plastic shield covering the blade.
-Black plastic cover, covering the electrical supply box.
Electrical equipment
-According to European Standard “CENELEC EN 60 204-1” which simulates modifications,
publication (IED 204-1)
-The electrical equipment ensures protection against electric shock as a result of direct or indirect
contact. The active parts of this equipment are housed in a box so that access is limited, the screws
can only be removed with a standard screwdriver.
-This equipment is protected against splashes of water and dust.
-This machine has been tested in conformity with EN 60204.
Recommendations for use
-This machine has been designed to cut metal building materials with different shapes, profiles
used in workshops and mechanical structural work.
-Only one operator is needed to use the machine.
-Before starting each cutting operation, ensure that the part is firmly gripped in the vice and that
the end is suitably supported.
-Do not use cutting blades of a different size from those stated in the cutting capacity section (next
page).
-If the cutting blade gets stuck in the work piece, release the blade ON button immediately, switch
off the machine, and open the vise slowly. Remove the part and make sure that the cutting blade
and/or its teeth are not damaged or broken.
CUT 250 COLD SAW
7/13/05 4
-Before carrying out any repairs on the machine, consult the distributor or DAKE.
Cutting capacity
CUTTING
CAPACITY
90* 1 1/8 2 3/4 2 1/2 3½ X 1 3/4
45* 1 2 3/8 2 1/8 2 ½ X 2
-Single Phase, single speed electric motor 1HP
-Reduction gear Ratio = 1:32
-Maximum blade diameter Inches 10
-Blade speed rotation rpm 44
-Max. Vice opening Inches 4 1/8
-Machine weight without stand Pounds 176
-Machine weight with stand Pounds 238
Machine Dimensions
All Dimensions are in Inches
Instructions when you receive your machine
CUT 250 COLD SAW
7/13/05 5
-When you receive your machine it will be wrapped in plastic (see illustration 3).
-Remove the plastic and set pedestal to the side.
-Remove wooden walls from the crate.
-There are two bolts securing the machine to the crate, remove these two bolts.
Illustration 3
Assembling the Pedestal
-Open the box and remove all pieces. You will have four large pieces with a bag of nuts and bolts
(see illustrations 4, 5 and 6)
Illustration 4 Illustration 5 Illustration 6
-Open the bag of nuts and bolts you will have the following contents (also see illistration7 on page
6):
2 – 13mm x 40mm
bolts 2 – 13mm nuts 8 – 12mm washers
4 – 10mm x 16mm bolts 2 – 31mm washers
2 – 23mm washers 4 – 10mm bolts
Piece 1 Piece 2 Piece 3 Piece 4
Bag of
nuts and
bolts
CUT 250 COLD SAW
7/13/05 6
Illustration 7
-Place both large pieces of the pedestal next to each other like in Illustration 4 on page 5.
- Take piece 4 and place between piece 1 and 2, as you will notice there are tabs on the sides, Put
these tabs in the holes of piece 1 and push down, the two pieces will snap together (see illustration
8 & 9). Do the same with piece 3.
Illustration 8 Illustration 9
-There are 4 holes on the inside of this pedestal (two on the front and two on the back side). Take
the 10mm x 16mm (see illustration 7) bolt and put one 12mm washer on it, put this bolt in the hole
located on the inside of the pedestal (see illustrations 10 & 11 next page), then put one 12mm
washer and one 10mm nut on, tighten nut as needed. Repeat this step for all four-bolt holes.
10mm x 16mm bolt
13mm x 40mm bolt
Piece 1
Piece 2
Tab
Hole for bolt
Piece 4
31mm
washer
23mm
washer 13mm nut
12mm washer
10mm nut
CUT 250 COLD SAW
7/13/05 7
Illustration 10 Illustration 11
-When you finish assembling the pedestal it will look like Illustration 12.
Illustration 12
Transporting and handling
-When you receive your machine use a forklift to transport the machine.
Hole on rear of
pedestal
Holes on
front of
pedestal
CUT 250 COLD SAW
7/13/05 8
-When lifting the machine use a sling.
How to mount your Cold Saw on the pedestal
-Place the machine on the pedestal so that the front of the machine is facing the front of the
pedestal (see illustration 14).
Illustration 14 illustration 15
-Use the two remaining bolts (13mm x 40mm) and put a 31mm washer on it, put the bolt into the
front mounting hole (see illustration 15). Put a 31mm washer on the bottom side of the bolt, now
put the 13mm nut on the bolt.
-See picture below (illustration 16) to mount the second bolt on the rear side of the machine.
Front side of
machine
Front side of
pedestal
Front
mounting hole
CUT 250 COLD SAW
7/13/05 9
Illustration 16
How to assemble the machine
-The following parts will be with your machine upon receiving: handle and a stock stop (see photo
on page 9).
Illustration 17
Illustration 18
Shipping bolt
Threaded hole
Front
mounting
hole
Rear
mounting
hole
Stock stop
Handle
CUT 250 COLD SAW
7/13/05 10
-Remove the shipping bolt (see illustration 18) and screw the handle in the hole. There is a white
plug that comes out of the handle, plug this into its receptacle located on the side of the electrical
box (see illustration 19). There is a lever on this attachment move this to the closed position as
seen on illustration 19.
Illustration 19
Anchoring The Machine
-Position the machine on a firm cement floor; keep a minimum distance of 2 1/2 feet from the
wall. Mount to the floor as shown in diagram
3.
Diagram 3
Instructions for electrical connection
Lever
Receptacle
Table of contents
Other Dake Saw manuals
Dake
Dake J-10 Installation and maintenance instructions
Dake
Dake E-16 User manual
Dake
Dake SXC 988040 User manual
Dake
Dake SE-8.5M Operating and maintenance manual
Dake
Dake E-16 User manual
Dake
Dake SUPER CUT 315 Operating and maintenance manual
Dake
Dake V-26 User manual
Dake
Dake SE-712 Operating and maintenance manual
Dake
Dake SE-10 DM User manual
Dake
Dake Technics 350 SA User manual
Dake
Dake SE-912 User manual
Dake
Dake 14-10 User manual
Dake
Dake Technics 350 CE Operating and maintenance manual
Dake
Dake Technics 250 Operating and maintenance manual
Dake
Dake SL913 TW Quick start guide
Dake
Dake SE-712 User manual
Dake
Dake F-16 User manual
Dake
Dake SE-5X8 Operating and maintenance manual
Dake
Dake JH-10 User manual
Dake
Dake SE-912 Operating and maintenance manual
