Daintree RM4 User manual

Installation Guide

RAIL287 | 99003834

RM4 LED Signals Rail

Tricolor Wayside Colorlight

10V Module Only

Voltage Range 8 to 16V DC

Input Voltage Range 10V DC

Current Draw Minimum of 1.35 A

BEFORE YOU BEGIN

Read these instructions completely and carefully. If you prefer to have this Installation Instructions

document in other languages, visit our ocial website at: www.gecurrent.com/transportation

Prepare Electrical Wiring

Electrical Requirements

• Follow all National Electric Codes (NEC)

and local codes.

Operating Specications

WARNING / AVERTISSEMENT

RISK OF ELECTRIC SHOCK

Disconnect Before Servicing or installing product. The LED module must be installed into a signal head with adequate ingress

protection for the location (protection from the weather).

RISQUES DE DÉCHARGES ÉLECTRIQUES

Couper l’alimentation avant le dépannage ou avant l’installation du produit. Le module DEL doit être installé dans une tête de signal

avec une protection adéquate d’entrée pour l’emplacement (protection contre les intempéries).

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAN ICES-005 (A)/NMB-005(A)

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

Important Information

• Use only with approved microprocessor-based controllers (refer to label on module cover) as follows:

GETS: EL2, VHLC, EC4, EC5

US & S: MICROLOCK II VERSION 8

• Vital programmable control systems or relay ashers are the only approved means of ashing the LED signal.

• LED module ts into most standard railway signal heads.

• LED module is self-contained – no assembly is required.

• As per AREMA guidelines, provisions should be made for periodic functional checks of safety devices and

features incorporated into this product.

• Current recommends that primary and secondary surge protection be added additional to the tertiary surge

protection in the lamp. Arema 11.3.3

• This product is intended solely for the use of rail signaling and is not intended for use in any other application.

RM4 LED Signals Rail Installation Guide

www.gecurrent.com

General Electric Company and are used under license. Information provided is subject to change without

notice. All values are design or typical values when measured under laboratory conditions.

RAIL287 (Rev 03/15/21) 99003834

Installation Steps

Existing signal head in the eld: Remove lens and

incandescent bulb assembly from housing.

Existing in-line rheostat in the eld: Set rheostat (variable

resistor) to zero (0) or remove completely.

Voltage settings: Check the label on the back of the LED

module to ensure the voltage corresponds to the system

voltage. The recommended voltage at the signal head is 10V.

Wiring: For wire installation, please follow guidelines shown

below.

Insertion of LED module into signal head: Insert the LED

module into lens slot and tighten metal tabs, or insert LED

module into the external ring holder.

Ensure arrow

points upward for

proper beam

Tighten plastic

thumb- nuts by

hand

Use wrench to

tighten the brass

hex nuts

Check label for

required voltage

To remove the

terminal block,

rst pivot the latch

Wire the terminals

as shown, use shrink

tubing color as a

guide

The terminal block

can then be pulled

by hand

NOTE: Failure to properly follow these instructions may cause signal to malfunction.

If testing before installation, be sure to use a constant power source rated 10V / 2 A minimum to ensure proper

operation of the LED signal. NOTE: Failure to do so will activate the light-out safety detection feature of the LED signal

and disable the lamp’s operation.

Testing

CAUTION

RISK OF ELECTRIC SHOCK

Install unit in enclosure tested to be suitable

for wet locations only.

CAUTION

If the lamp is NOT inserted in the correct

orientation, the light output of the lamp

output will not meet specication

CAUTION

SOME SURFACES MAY BE HOT

This manual suits for next models

Table of contents

Other Daintree Lighting Equipment manuals

Daintree

Daintree GE current Lumination LRX Series User manual

Daintree

Daintree GE Forum Frame IND739 User manual

Daintree

Daintree GE Current UltraMax GED80MCC/Z2P1500 User manual

Daintree

Daintree GE current Immersion GELP24-100U-GLX User manual

Daintree

Daintree GE current Tetra Contour User manual

Daintree

Daintree GE Tetra Atom User manual

Daintree

Daintree GE current Tetra PowerStrip DS User manual

Daintree

Daintree GE Current Arize Life2 User manual

Daintree

Daintree GE current Proline LEX Series User manual

Daintree

Daintree GE current Tetra PowerStrip Snap DS User manual

Daintree

Daintree GE GEXNLG15 User manual

Daintree

Daintree GE current Lumination RC Series User manual

Daintree

Daintree GE Tetra miniMAX User manual

Daintree

Daintree GE Current Tetra GEPS24-25U-NA User manual

Daintree

Daintree GE Current Tetra GEPS12-25U-NA User manual

Daintree

Daintree GE Current RAIL159 User manual

Daintree

Daintree Contour Gen 2 Flex User manual

Daintree

Daintree GE Tetra MAX User manual

Daintree

Daintree GE current Evolve EFC1 Series User manual

Daintree

Daintree GE Current Lumination LRXD Series User manual

Daintree

Daintree GE cirrent Tetra Rigid Light Bar User manual

Daintree

Daintree GE current Tetra GETP35-2 User manual

Daintree

Daintree GE Current Arize Factor User manual

Popular Lighting Equipment manuals by other brands

Brizo

Brizo 8SP-MU-4 manual

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 installation instructions

IKEA

IKEA BJÖRKSPIREA manual

Laserworld

Laserworld Evolution Series ES-400RGB manual

Alien

Alien RG STAR user manual

EuroLite

EuroLite LED B-40 user manual

Qazqa

Qazqa Suplux SL 3 Black 103062 instruction manual

Commercial Electric

Commercial Electric 54568141 Use and care guide

CREE LIGHTING

CREE LIGHTING 304 Series installation instructions

Goobay

Goobay 49867 user manual

ECOMAN ITALIA

ECOMAN ITALIA LED T8 instruction manual

Alkalite

Alkalite Krypton KT-81 user manual

Clas Ohlson

Clas Ohlson GU10 manual

DTS

DTS DELTA 10 F user manual

ring

ring Solar Steplight manual

One Stop Gardens

One Stop Gardens 57696 Owner's manual & safety instructions

Chauvet DJ

Chauvet DJ COREpar UV120 ILS user manual

SIREM

SIREM Swimeo A2 instructions