Daikin ARC417A14 User manual

ARC417 Series Si10-416A

80 Remote Controllers

ARC417A14, A15

Open

the

cover.

MODE

FAN

CANCEL

ON/OFF

TEMP

SWING

OFF

TIMER

TIME

TIMER

DOWN

POWERFUL

SILENT

HOME LEAVE

Si10-416A ARC417 Series

Remote Controllers 81

1. Transmitter

It sends signals to the indoor unit.

2. ON/OFF button

Press it once to start operation. To stop it, press it

once again.

3. Display

It displays the current settings.(In this illustration, each

section is shown with all its displays ON for the

purpose of explanation.)

4. TEMPERATURE / TIME adjustment buttons

It changes the temperature or time setting.

5. CLOCK button

6. OFF TIMER button

7. ON TIMER button

8. TIMER CANCEL button

It cancels the timer setting.

9. FAN setting button

It selects the air flow rate setting.

10. MODE selector button

It selects the operation mode.

(AUTO / DRY / COOL / HEAT / FAN)

11. SWING buttons

12.OUTDOOR UNIT SILENT button

13. POWERFUL button

14. HOME LEAVE button

Indicator lamps

OPERATION lamp (green)

HOME LEAVE lamp (red)

TIMER lamp (yellow)

•

Lights up when you use HOM

LEAVE Operation.

ON/OFF switch

Unit operation panel and display panel

ARC417 Series Si10-416A

214 Operation

3. ARC417 Series

3.1 Preparation Before Operation

Setting the batteries

1Press with a finger and slide the back

cover to take it off.

2Set two alkaline dry batteries (LR03).

3Set the back cover as before.

This will cause the figures on the display

to flash. Set the clock at this point.

Position + and

– correctly!

Address switch

Remote controller

Si10-416A ARC417 Series

Operation 215

Receiver

Operating the remote controller

To use the remote controller, aim the transmitter at

the indoor unit. If there is anything to block signals

between the unit and the remote controller, such as

a curtain, the unit will not operate.

Do not drop the remote controller. Do not get it wet.

The maximum distance for communication is about

7 m.

To remove, pull it upwards.

Remote controller

holder

Set.

Push.

To fix the remote controller

holder on the wall

Choose a place from where the signals reach

the unit.

Fix the holder to a wall, a pillar, etc. with the

screws supplied with the holder.

Fit the claw of the holder into the bottom of

the remote controller, and push the remote

controller onto the wall.

ARC417 Series Si10-416A

216 Operation

Setting the air purifying filters

Indoor unit

Open the front grille.

Hold the grille by the tabs on the two sides

and lift it until it stops with a click.

(about 60˚)

Pull out the air filters.

Push upwards the

tab at the center of

each air filter, then

pull it down.

Set the air purifying filters.

Attach an air purifying filter to each air filter.

Set the air filters in their original

positions and close the front grille.

Operation without air filters may result in

troubles as dust will accumulate inside the

indoor unit.

Si10-416A ARC417 Series

Operation 217

Setting the clock

Turn the breaker ON

Press .

blinks.

Press

present time.

rapidly increases or decreases the time display.

Holding down ( ) or ( ) button

Turning ON the breaker opens the flap, then

closes it again. (This is a normal procedure.)

to set the clock to the

is displayed.

blinks.

ARC417 Series Si10-416A

218 Operation

Be careful not to cool (heat) the room too much.

Keeping the temperature setting at a moderate

level helps save energy.

Cover windows with a blind or a curtain.

Blocking sunlight and air from outdoors

increases the cooling (heating) effect.

The air conditioner always consumes 15 – 35 watts of

electricity even while it is not operating.

If you are not going to use the air conditioner for a long

period, for example in spring or autumn, turn the breaker OFF.

Use the air conditioner in the following conditions.

(*1) Use in humidity 60 % or lower when using the unit at an

outdoor temperature of 10˚C or lower.

Clogged air filters cause inefficient

operation and waste energy. Clean them

once in about every two weeks.

For cooling: 26˚C – 28˚C

For heating:20˚C – 24˚C

NOTE

Tips for saving energy

Please note

Recommended temperature setting

Mode Operating conditions

Outdoor temperature 2A safety device may work to stop the

operation.

(In multi system, it may work to stop

the operation of the outdoor unit

only.)

2Condensation may occur on the

indoor unit and drip.

2A safety device may work to stop the

operation.

Indoor temperature

: 18 to 32 ˚C

Indoor humidity : 80% max. (*1)

RKD, RXD, RMX : –5 to 46 ˚C

3MX : 21 to 43 ˚C

4MX : 10 to 43 ˚C

3MK, 4MK : 10 to 46 ˚C

RMK : 5 to 46 ˚C

Outdoor temperature

Indoor temperature

: 10 to 30 ˚C

RKD, RXD : –15 to 24 ˚C

3MX, 4MX : –10 to 24 ˚C

RMX : –15 to 24 ˚C

If operation is continued out of this range

COOL/

DRY

HEAT

Si10-416A ARC417 Series

Operation 219

3.2 AUTO • DRY • COOL • HEAT • FAN

Operation

ARC417 Series Si10-416A

220 Operation

Si10-416A ARC417 Series

Operation 221

This manual suits for next models

Table of contents

Popular Remote Control manuals by other brands

Panasonic

Panasonic EUR7622KB0 Operation guide

Bang & Olufsen

Bang & Olufsen Beo4 user manual

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 user manual

Multiplex

Multiplex PROFI TX 9 instructions

One Remote

One Remote RMB4 user manual

FUTABA

FUTABA 9ZAP - PART2 manual

HR Matic

HR Matic HR MULTI 3 quick start guide

Yamaha

Yamaha ACC-GNRST-30-20 installation instructions

EisSound

EisSound KBSOUND user manual

Marantz

Marantz RC101 user guide

Conrad

Conrad FS20 TC6 operating instructions

Anritsu

Anritsu MP1777A Operation manual

Niles

Niles WVC100 Installation & operating guide

RCA

RCA RCU1300 manual

Bang & Olufsen

Bang & Olufsen BEO6 Getting started

GE 94901 instruction manual

Onbon

Onbon YQ1-75 user manual

FUTABA

FUTABA R7108SB Full manual