Daewoo FR-2703 User manual

FEATURE CHART

(

)

! ICE TRAY

@ F SHELF (MOVABLE)

# FREEZER TEMPERATURE CONTROL

KNOB

$ ICE BOX

% CHILLED CASE

^ LAMP COVER

& REFRIGERATOR TEMPERATURE

CONTROL SWITCH

* R SHELF (MOVABLE)

( VEGETABLE CASE COVER

) VEGETABLE CASE

1 FREEZER POCKET

2 UTILITY POCKET

3 EGG CASE

4 BOTTLE POCKET(LARGE)

5 BOTTLE POCKET(SMALL)

Here are the features of your new refrigerator.

Take a moment to know all the features designed for the convenience of the user.

󱇲󱇲Ice Tray

Fill 3/4 of the ice tray with water, as the volume expands when the water is frozen. Place the tray

in the freezer compartment. To release ice cubes, twist the ice tray slightly. Ice cubes will be

easier to remove if it is held for a short while under running water.

󱇲󱇲Moveble refrigerator and freezer shelves

Storage shelves should be adjusted depending on the height of the food stored. To do this, pull

the shelves slightly forward.

󱇲󱇲Defrost-drain Vessel

Since dust acoumulated on the drain case decreases the evaporation efficiency. You should

clean the drain case at regular intervals.

󱇲󱇲Lamp cover

To remove the lamp cover

1. Push up the bottom end of lamp cover gently,

then pull out.

2. Reverse procedure to join together.

󱇲󱇲Vegetable case

May be used for fruit and vegetable storage.

Both the vegetable case and its cover shelf are

removable for easy cleaning. Simply slide

forward to remove.

󱇲󱇲Utility Pocket (Top)

The Egg Case in this pocket can be turned

upside down for the use of small size goods.

󱇲󱇲For lock installed refrigerators only.

CAUTION: 1. Check your voltage before inserting the power supply cord into the socket.

2. Contact the earthing conductor to this unit with an attachment earthing screw.

3. Do not spill liquid on this unit.

4. Do not use flammable spray, such as painting, near this unit.

5. Do not place ignitable material, such as benzine, L.P. gas, alcohol etc., into this

unit.

6. Take precautions against leakage of any gas equipment near this unit.

7. Keep children from hanging on the door of this unit.

8. Do not reinsert the power supply cord within 5 minutes after releasing it from the

socket. If not, there may be problems with the compressor.

CAUTION

When you put or take out food from the refrigerator, be careful not to hit your head on the lock

as there is a protrusion on the door of your refrigerator.

METHODS OF SAFE INSTALLATION

1. SAFE INSTALLATION PLACE FOR YOUR REFRIGERATOR

• Place the refrigerator on a

strong and level floor.

Unstable installation can

produce noise and

vibration.

• Place your refrigerator

where there is no heat

source nearby.

High atmosphere

temperature will lower

cooling efficiency and

increase your electricity bill.

• Place the refrigerator in an

area where the humidity

level is low.

Splashing water on the

refrigerator or installing the

unit in a humid area may

cause short circuit and rust.

• Avoid places that are

exposed to coal gas or

smoke, as discoloring may

occur on the refrigerator.

• For good ventilation, keep

enough space between the

sidewalls and your

refrigerator.

This helps to cool efficiently

and lowers the electricity bill.

• Putting the refrigerator on

the carpet may cause a

temperature rise and result

in the discoloring of the

carpet due to the

compressor heat.

In such a case, place a

hard wooden board or a

rubber mat between the

carpet and the unit.

Carpet

Wooden Board,

Rubber Mat

2. INSTALLATION STEPS

• Select a safe place to install

your refrigerator. • Level the refrigerator by

using the adjustable feet. • Install the parts in their own

place.

• Check if the doors are

completely closed. • Check the voltage.

Then wait about an hour

before plugging the power

cord into the outlet.

• Put food in the refrigerator

after running the refrigerator

for 2~3 hours.

Safe installation

Place

Maintain ~

Level

Components to their

original places

Check

Plug in after

about hour

Put food after

2~3 hours

3. WHAT YOU NEED TO KNOW BEFORE MOVING OR

RELOCATING THE REFRIGERATOR!

• Unplug the power cord. • Remove the grille with driver

and water from the defrost-

drain vessel located at the

rear of the refrigerator.

• Do not detach the defrost

drain vessel from the

compressor.

• Take food out of the

refrigerator.

• Fasten the interior

components with adhesive

tape.

• Have two people carry the

refrigerator to move safely.

• Fasten the doors with

adhesive tape to prevent

from opening while moving.

Adhesive

Tape

AdhesiveTape

4. CLEANING YOUR REFRIGERATOR

• Before you clean the

refrigerator, unplug the

power cord. To clean, use a

soft piece of cloth. Wash

with warm, soapy water

rinse and dry.

• The refrigerator may smell

during initial operation, but

the odour will fade away

when the refrigerator is

cooled sufficiently.

• Use a soft cloth for cleaning

the interior and exterior of

the refrigerator.

• Do not sprinkle water

directly on the refrigerator

itself.

• Put the parts back in their

original positions after

cleaning.

Soft cloth

Water

Components to their

original places

Leveling

Location

How to Install

Install the refrigerator in a convenient location away from extreme heat and cold. Allow at least 6cm

clearance between the refrigerator and side wall so that the door may open for a fully usable interior

and the refrigerator may have good air circulation. The refrigerator is not designed for recessed

installation.

󱇲Select a strong and level floor.

󱇲Keep 6cm of space between the refrigerator

and the walls.

Level the refrigerator so that it rests solidly on the floor without rocking. There are two leveling feet at

each front corner. Turn to the left to raise a corner, to the right to lower it. Use shims under the rear

corners, if necessary.

󱇲If you want the refrigerator door to close naturally, adjust the leveling feet so that the front of the

refrigerator is raised by 5mm.

󱇲If you want the refrigerator to remain motionless when open, adjust the leveling feet so that all

four corners are leveled with each other.

NOTE: All packing materials used to ensure safety during transport should be removed. You

must remove the transport safety packing and wipe off any possible adhesive tape

residues with a petroleum-based cleaner or similar solvent.

6cm

the wall

1. Clean the refrigerator thoroughly. Wipe the outside with a dry cloth, and the inside with a damp cloth.

2. Set the temperature control knob at normal position.

3. Connect the power supply cord.

Many factors may influence the internal temperature of the refrigerator and freezer

compartments.

󱇲󱇲The temperature and humidity of the surrounding environment.

󱇲󱇲The opening frequency of the doors and the amount of warm food placed in the refrigerator.

󱇲󱇲The combination of food and containers stored in the refrigerator.

For these reasons, you may want to adjust the control to suit the season and your needs.

To control temperature

How to operate

1. TEMPERATURE CONTROL

Temperature is controlled by thermostat automatically.

The Temperature Control inside the refrigerator controls the degree of cooling for each

compartment.

Freezer Temperature Control

The control has four settings from MIN to

WINTER. The WINTER mode is available

only if atmosphere temperature is below 10°C.

TEMP. CONTROL

MIN MED MAX WINTER

WINTER

MAX

MED MIN

TEMP. CONTROL

Starting your new refrigerator

Refrigerator Temperature Control

The control has four settings from MIN to

WINTER. The WINTER mode is available

only if atmosphere temperature is below 10°C.

󱇲󱇲Turn the temperature control in the refrigerator and freezer compartments toward WINTER for

colder temperature and toward MIN for warmer temperature.

󱇲󱇲Allow approximately 12 hours or overnight for the temperature to stabilize,

then check to see if further adjustments are necessary.

Disconnect the power supply cord. Remove icing case and food. Leave doors ajar for ventilation and

dehumidification of both compartments.

2. DEFROSTING THE REFRIGERATOR

You will never have to defrost your refrigerator as it is designed to defrost itself completely and

automatically.

3. RADIANT HEAT

With the Refrigerating System in operation, it is likely that the cabinet will feel warm at the front

edges and sides. This does not indicate trouble.

It is due to the hot-line used in this type of Refrigerating System which consists of piping hot gas

from the (motor-driven) compressor along the front edges, the sides of the cabinet and the center

partition to prevent dewung. This has nothing to do with the storage temperature inside.

(The thick line indicates the hot-line)

To turn off the refrigerator

CAUTION

To avoid the risk of electric shock or death, unplug the power cord before replacing a

burned out light bulb or cleaning the inner parts.

NOTE: During spells of hot, humid weather and in rainy season,

moisture may develop on the cabinet, just as water

condenses around a cold glass of water. It is not an

abnormal condition; wipe off the moisture with a dry cloth.

This can also happen when the refrigerator is not installed

in an appropriate place.

Table of contents

Other Daewoo Refrigerator manuals

Popular Refrigerator manuals by other brands

Bonnet Neve

Bonnet Neve SKYVIEW PLUS User instructions

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Instruction book

Sharp

Sharp SJ-BA31IEXW2-EU user manual

CORBERO

CORBERO CC2300MCW Instruction booklet

KitchenAid

KitchenAid 2205264 Use and care guide

Stengel

Stengel KU 1101 A++ user manual

NEFF

NEFF KI181 Series user manual

Hoshizaki

Hoshizaki Reach-In instruction manual

Amana

Amana ASD2524VES00 User instructions

BOMANN

BOMANN KGC 213 instruction manual

Danby

Danby DAR044A1SLDD Owner's use and care guide

Samsung

Samsung RF323TE user manual

Beko

Beko CSA31022 Instructions for use

IKEA

IKEA FROSTIG C 185 E manual

Electrolux

Electrolux ER 6821 D Instruction book

True

True TS-28 Specifications

Frigidaire

Frigidaire FSC23R5DW9 installation guide

Beko

Beko LSP4579W Instructions for use