D-Link DGS-1216T - Switch Operator's manual

Before Your Begin

This Quick Installation Guide gives step-by-step instructions for setting up the D-Link

DGS1216T Gigabit Smart Switch. The model you have purchased may appear slightly

different from those shown in the illustrations. For more detailed information about the

switch, its components, making network connections and technical specifications,

please refer to the User’s Manual on master CD included with your switch.

Check Your Package Contents

These are the items included with your DGS-1216T purchase:

If any of the above items are missing, please contact your reseller.

holders. Software and specifications subject to change without notice.

• DGS-1216T

D-Link 16-Port 10/100/1000Mbps + 2 Combo

Mini GBIC Gigabit Smart Switch

• CD-ROM (containing Manual and Utility

Installation)

• 100–240VAC 50/60Hz

Power Adapter

Using a powe

supply with a

different voltage rating

will damage and void

the warranty for this

product.

DGS-1216T

D-Link 16-Port

10/100/1000Mbps + 2 Combo

Mini GBIC Gigabit

Smart Switch

Setup The DGS-1216T Gigabit Smart

Switch

The setup of the Switch can be performed using the following steps:

A. Install the DGS-1216T in a fairly cool and dry place. See Technical

Specification for the acceptable operation temperature and humidity

ranges.

B. Install the DGS-1216T in a site free from strong electromagnetic

field generators (such as motors), vibration, dust, and direct

exposure to sunlight.

C. Leave at least 10cm (about 4 inches) of space at the front and rear

of the hub for ventilation.

D. Visually inspect the DC power jack and make sure that it is fully

secured to the power adapter.

E. Install the DGS-1216T on a sturdy, level surface that can support

its weight, or in an EIA standard-size equipment rack.

F. When installing the Switch on a level surface, attach the rubber feet

to the bottom of each device. The rubber feet cushion the hub and

protect the hub case from scratching.

Attach the adhesive rubber pads to the bottom

Rack Mounting

The DGS-1216T can be mounted in an EIA standard-size, 19-inch rack,

which can be placed in a wiring closet with other equipments. Attach the

mounting brackets to both sides of the Switch (one at each side), and

secure them with the provided screws.

Use the screws provided. Then, use screws provided with the

equipment rack to mount the Switch in the rack.

Mount the Switch in the rack

Connecting Network Cable

The DGS-1216T supports 10/100/1000Mbps Gigabit Ethernet. It runs

full/half duplex transfer mode for 10/100Mbps and full duplex transfer

mode for 1000Mbps. Each port on the DGS-1216T supports Auto-

MDI/MDI-X. Auto-MDI/MDI-X is a feature that eliminates the need for

worrying about using either a standard or crossover cable—you can

use either one—and allows any port to be an uplink port.

AC Power

The DGS-1216T can be used with AC power supply 100~240V AC,

50~60Hz. The power switch is located at the rear of the unit adjacent to

the AC power connector and the system fan. The switch’s power supply

will adjust to the local power source automatically and may be turned on

without having any or all LAN segment cables connected.

Connect The DGS-1216T Gigabit

Smart Switch To Your Network

Front Panel

10/100/1000 Base-T Mini GBIC Ports

Twisted-Pair Ports

┌───────────────┐ ┌──┐

└─────────┘

LED Indicators

1000BASE-T Twisted Pair Ports (Port 1~16)

The DGS-1216T is equipped with 16 Gigabit twisted pair ports that are

auto negotiable 10/100/1000Mbps and also support auto MDI/MDIX

crossover detection. These two ports can operate in half- and full-

duplex modes.

Mini GBIC Ports (Option Port 15~16)

The Switch is equipped with two Mini GBIC ports, supported optional

1000BASE-SX/LX Mini GBIC module.

Note: When the port was set to “Forced Mode”, the Auto

MDI/MDIX will be disabled.

LED Indicators

LED stands for Light-Emitting Diode.

The front panel LEDs provides instant status feedback and simplifies

monitoring and troubleshooting tasks.

LED indicators of the Switch

Power LEDs

On When the Power LED light is on, the Switch is

receiving power.

Off When the Power LED light is off, the power cord is

improperly connected.

CPU LEDs ( Management Indicator)

Blinking When the CPU is working, the System LED is

blinking.

On/Off The CPU is not working.

Ports 1 & 16 Status LEDs

Link/Act

On When the Link/Act LED lights on, the respective

port is successfully connected to an Ethernet

network.

Blinking When the Link/Act LED is blinking, the port is

transmitting or receiving data on the Ethernet

network.

Off No link.

1000Mbps

On When the 1000Mbps LED lights on, the

respective port is connected to a 1000Mbps

Gigabit Ethernet network.

Off When the respective port is connected to a

10Mbps Ethernet or 100Mbps Fast Ethernet

network.

100Mbps

On When the 100Mbps LED lights on, the respective

port is connected to a 100Mbps Fast Ethernet

network.

Off When the respective port is connected to a

10Mbps Ethernet or 1000Mbps Gigabit Ethernet

network.

Option Ports 15~16 Mini-GBIC Status LEDs

Link/Act

On When the Mini GBIC module is installed and

connected to a network, the Link/Act LED lights on.

Blinking When the LED is blinking, the Mini GBIC module is

receiving data on a network.

Off No link.

1000Mbps

On When the 1000Mbps LED lights on, the respective

port is connected to a 1000Mbps Gigabit Ethernet

network.

Off When the respective port is disconnected to the

network

Installing the SmartConsole Utility

The following instruction guides you to install the SmartConsole utility.

1. Insert the Utility CD in the CD-Rom Drive.

2. From the Start menu on the Windows desktop, choose Run.

3. In the Run dialog box, type D:\SmartConsole Utility\setup.exe (D:\

depends where your CD-Rom drive is located) and click OK.

4. Follow the on-screen instructions to install the utility.

5. Upon completion, go to Program Files -> SmartConsole Utility

and execute the SmartConsole utility. (Figure 1.)

Figure 1. SmartConsole Utility

Configuring the Switch

The DGS-1216T has a Web GUI interface for smart switch configuration.

The Switch can be configured through the Web Browser. A network

administrator can manage, control and monitor the switch from the local

LAN. This section indicates how to configure the Switch to enable its

smart functions.

Use Internet Explorer 5.5 or above Web browser.

Before you configure this device, note that when the Web Smart Switch

is configured through an Ethernet connection, make sure the manager

PC must be set on the same IP network. For example, when the default

network address of the default IP address of the Web Smart Switch is

192.168.0.1, then the manager PC should be set at 192.168.0.x (where x

is a number between 2 and 254), and the default subnet mask is

255.255.255.0.

Enter IP address http://192.168.0.1 (the factory-default IP address

setting) to the address location. (Figure 2.)

Figure 2.

Or through the SmartConsole Utility, you do not need to remember the IP

Address, select the device shown in the Monitor List of the

SmartConsole Utility to settle the device on the Web Browser.

When the following dialog page appears, remain enter the default

password "admin" and press Ok to enter the main configuration window.

(Figure 3.)

Figure 3.

After entering the password, the main page comes up, the screen will

display the device status. (Figure 4.)

Figure 4.

Setup Menu

When the main page appears, find the Setup menu in the left side of the

screen (Figure 5). Click on the setup item that you want to configure.

There are following options: System Setting, Trap Setting, Port Setting,

SNMP Setting, Password Access Control, Jumbo Frame, 802.1Q VLAN,

Trunking, IGMP Snooping, 802.1D Spanning Tree, Port Mirroring, 802.1p

Default Priority, Safeguard Engine, Broadcast Storm Control, 802.1X

Setting, Static MAC, Dynamic Forwarding Table, Statistics as shown in

the Main Menu screen.

Figure 5.

Tool

You also find the Tool in main page. Click on and scroll down as shown

in Figure 6, there are four options: Reset, Config Backup & Restore,

Firmware Backup & Upload, System Reboot.

Figure 6

Technical Support

You can find software updates and user documentation on the D-Link websites.

D-Link provides free technical support for customers within Canada,

the United Kingdom, and Ireland.

Customers can contact D-Link technical support through our websites,

or by phone.

For Customers within

The United Kingdom & Ireland:

D-Link UK & Ireland Technical Support over the Telephone:

08456 12 0003 (United Kingdom)

+44 8456 12 0003 (Ireland)

Lines Open

8.00am-10.00pm Mon-Fri

10.00am-7.00pm Sat & Sun

D-Link UK & Ireland Technical Support over the Internet:

http://www.dlink.co.uk

ftp://ftp.dlink.co.uk

For Customers within Canada:

D-Link Canada Technical Support over the Telephone:

1-800-361-5265 (Canada)

Mon. to Fri. 7:30AM to 9:00PM EST

D-Link Canada Technical Support over the Internet:

http://support.dlink.ca

email: support@dlink.ca

Other manuals for DGS-1216T - Switch

Table of contents

Other D-Link Switch manuals

D-Link

D-Link DGS-3130-54TS User manual

D-Link

D-Link DGS-3630-52TC User manual

D-Link

D-Link DUB-H4 User manual

D-Link

D-Link DE-816TP - Hub 16Port 10MBs 16RJ45 1BNC 1A Ui... User manual

D-Link

D-Link DUB-1325 User manual

D-Link

D-Link DIS-F200G Series User manual

D-Link

D-Link DFB-H7 User manual

D-Link

D-Link DFE-916x User manual

D-Link

D-Link DGS-1224T - Web Smart Switch User manual

D-Link

D-Link DUB-M910 User manual

D-Link

D-Link DES-1008P User manual

D-Link

D-Link DAS-3636 User manual

D-Link

D-Link KVM-121 User manual

D-Link

D-Link DES-7200 Manual

D-Link

D-Link DES-F1026P-E User manual

D-Link

D-Link DGS-1008MP User manual

D-Link

D-Link DGS-1210-10P User manual

D-Link

D-Link DES-1018P User manual

D-Link

D-Link Web Smart DES-1210-28 User manual

D-Link

D-Link DWS-3160 Series User manual

D-Link

D-Link DES-1005P User manual

D-Link

D-Link DWS-3160-24TC Manual

D-Link

D-Link DUB-M810 User manual

D-Link

D-Link xStack DGS-3420-28SC User manual

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Getting started guide