D-Link DIR-130 - Broadband VPN Router Setup guide

D-Link Technical Support – How to setup an IPSec VPN connection between a DIR-130 and DI-80xHV Page 1of 10

How to setup an IPSec VPN connection between a DIR-130 and DI-80xHV

This setup example uses the following network settings:

In our example the IPSec VPN tunnel is established between two LANs: 192.168.0.x and

192.168.1.x.

NOTE: It is essential to have private networks (LAN 1 and LAN 2) on different subnets.

D-Link Technical Support – How to setup an IPSec VPN connection between a DIR-130 and DI-80xHV Page 2of 10

Configuration of the DIR-130

Step 1. Log into the DIR-130 by opening Internet Explorer and typing the LAN address of the

device. In our example we are using the default 192.168.0.1. Enter Username and Password

which you specified during the initial setup of the Firewall.

Step 2: Click on SETUP, select VPN SETTINGS, and select IPSec from the ADD VPN

PROFILE dropdown list and click Add.

D-Link Technical Support – How to setup an IPSec VPN connection between a DIR-130 and DI-80xHV Page 3of 10

Step 3: Configure the IPSec VPN as followed:

IPSEC SETTING

•Enable: check box to enable

•Name: enter a name for the VPN

•Encapsulation Mode:: Tunnel

•Remote IP: select Site to Site and enter the remote gateway

•Remote Local LAN Net /Mask: enter the remote network and remote subnet mask

Authentication: enter a Pre-shared Key (Pre-share key must match remote side)

PHASE 1

•IKE Proposal List: leave at default (3DES, SHA1)

PHASE 2

•IPSec Proposal List: leave at default (3DES, SHA1)

Click Save Settings.

D-Link Technical Support – How to setup an IPSec VPN connection between a DIR-130 and DI-80xHV Page 4of 10

D-Link Technical Support – How to setup an IPSec VPN connection between a DIR-130 and DI-80xHV Page 5of 10

Configuration of DI804HV/808HV

Step 1: Open your web browser and type in the IP address of the router (192.168.0.1 by

default). Enter the username (admin by default) and password (blank by default), and then

click OK.

In our setup we changed the IP of the unit to 192.168.1.1 (NOTE both routers can not be

on the same subnet).

Step 2: Click on the Home tab and select the VPN button and configure as followed:

•VPN: check to enable

•Max. number of tunnels: enter the number of tunnels

ID 1

•Tunnel Name: enter a name of the VPN

•Method: select IKE

Click Apply to save the settings.

D-Link Technical Support – How to setup an IPSec VPN connection between a DIR-130 and DI-80xHV Page 6of 10

Step 3: Click on More under Method and configure as followed:

Tunnel Name: the name of the tunnel should already be entered if done in the previous step

•Local Subnet: enter the local subnet (192.168.0.0 in this example)

•Local Netmask: enter the local subnet mask(255.255.255.0 in this example)

•Remote Subnet: enter the remote subnet (192.168.1.0 in this example)

•Remote Netmask: enter the remote subnet mask(255.255.255.0 in this example)

•Remote Gateway: enter the remote gateway (172.68.140.140 in this example)

•IKE Keep Alive (Ping IP Address): enter an IP address of a client on the remote side

(192.168.1.100 in this example)

•Preshare Key: enter preshare key as desired (Pre-share key must match remote side)

•IPSec NAT Traversal: check to enable

•Auto-reconnect: check to enable

Click Apply to save the settings and click Continue when prompted.

D-Link Technical Support – How to setup an IPSec VPN connection between a DIR-130 and DI-80xHV Page 7of 10

Step 4: Click on Select IKE Proposal and configure as followed:

•Proposal Name: enter a name for the Proposal ID Number 1

•DH Group: Group 2

•Encrypt algorithm: 3DES

•Authentication Algorithm: SHA1

•Life Time: 28800

•Life Time Unit: Sec

•Proposal ID: select 1and click on Add To to add to the IKE Proposal index

Click Apply and then click Back.

D-Link Technical Support – How to setup an IPSec VPN connection between a DIR-130 and DI-80xHV Page 8of 10

Step 5: Click on Select IPSec Proposal and configure as followed:

•Proposal Name: enter a name for Proposal ID Number 1

•DH Group: Group 2

•Encapsulation Protocol: ESP

•Encryption Algorithm: 3DES

•Authentication Algorithm: SHA1

•Life Time: 3600

•Life Time Unit: Sec.

•Proposal ID: select 1and click on Add To to add to the IPSec Proposal index

Click Apply and then click Continue when prompted.

D-Link Technical Support – How to setup an IPSec VPN connection between a DIR-130 and DI-80xHV Page 9of 10

Step 6: Click on the Status tab and select the VPN Status button. The VPN should be

established. If the tunnel has not been established, click on the Refresh button or ping to an

IP address on the remote side. When replies are sent back, the tunnel has been established.

D-Link Technical Support – How to setup an IPSec VPN connection between a DIR-130 and DI-80xHV Page 10 of 10

Connecting to shared resources via VPN

To connect to shared resources via VPN you can map remote computers’ drives and folders

by opening Windows Explorer and going to Tools > Map Network Drive (you need to specify

the IP address of the computer on remote network and the name of the shared folder):

Alternatively you can do Search > Computers or People > Computer on Network > specify the

IP address of the computer you are trying to connect to.

If you do not see computers in My Network Places or My Network Neighbourhood you may

need to enable NetBIOS over TCP/IP in Windows.

Note that firewall/antivirus software installed on your or remote computer may stop you from

accessing remote network.

Other manuals for DIR-130 - Broadband VPN Router

Table of contents

Other D-Link Network Router manuals

D-Link

D-Link DIR-300 - Wireless G Router User manual

D-Link

D-Link DIR-330 - Wireless G VPN Router User manual

D-Link

D-Link DSL-2540B - ADSL2/2+ Modem With EN Router User manual

D-Link

D-Link DIR-X5460 User manual

D-Link

D-Link EBR-2310 - EN Broadband Router User manual

D-Link

D-Link DIR-868L User manual

D-Link

D-Link COVR- C1203 User manual

D-Link

D-Link 2Voice + 4SW VoIP Router DVG-1402S User manual

D-Link

D-Link SharePort DIR-825 User manual

D-Link

D-Link DIR-615 - Wireless N Router Installation guide

D-Link

D-Link DSL-504 User manual

D-Link

D-Link SharePort DIR-825 User manual

D-Link

D-Link DIS-300G Series User manual

D-Link

D-Link DIR-822 User manual

D-Link

D-Link DIR-513A User manual

D-Link

D-Link DSL-500 User manual

D-Link

D-Link DSL-502T User manual

D-Link

D-Link DES-1048 User manual

D-Link

D-Link DES-1008PA User manual

D-Link

D-Link DSL-526B User manual

D-Link

D-Link DIR-2150 User manual

D-Link

D-Link DWR-980 User manual

D-Link

D-Link DIR-885L User manual

D-Link

D-Link DSL-526B User manual

Popular Network Router manuals by other brands

Allnet

Allnet ALL0333AU user guide

HomeSeer

HomeSeer HT-SEL Getting started guide

Sercomm

Sercomm Genesis OC3505D Quick installation guide

Billion

Billion BIPAC 5102 Series user manual

TP-Link

TP-Link TD-8817 QIG

Motorola

Motorola MR1900 user guide

Digi

Digi IX14 user guide

Cisco

Cisco NCS 540 Hardware installation guide

XAVi

XAVi X8821e user manual

BEC

BEC 6200WZL Quick installation guide

MikroTik

MikroTik hAP ac3 Series quick start

Korenix

Korenix JetNet 5428G Series user manual

NETGEAR

NETGEAR FS526T - Switch installation guide

Korenix

Korenix JetNet 5710G Series user manual

Automated Logic

Automated Logic ZN551 Technical instructions

Cisco

Cisco ASR 1000 Series Installation and configuration guide

EnGenius

EnGenius ESR-9710 quick start guide

Cisco

Cisco 805 Series Product overview