Cypress CapSense CY3280-BMM User manual

CY3280-BMM Universal CapSense™ Matrix

Button Module Kit Quick Start

Doc. # 001-51788 Rev. *A

Cypress Semiconductor

198 Champion Court

San Jose, CA 95134-1709

Phone (USA): 800.858.1810

Phone (Intnl): 408.943.2600

http://www.cypress.com

trademarks, and PSoC®is a registered trademark of Cypress Semiconductor Corp. All other trademarks or

registered trademarks referenced herein are property of the respective corporations.

Cypress Semiconductor Corporation

198 Champion Ct., San Jose, CA 95134 USA

www.cypress.com

If you have questions, call

Cypress Customer Support

+1 (800) 541-4736 Ext. 8 (in the USA),

+1 (408) 943-2600 Ext. 8 (International),

or visit www.cypress.com/go/support

Doc. # 001-51788 Rev. *A

■Click Toggle Device Power button. The Power LEDs D1, D2 on the CY3280-

20x34 UCC board lights up. Corresponding LEDs on other UCC board's lights up.

5. Test the Board

■Touch one button at a time with your finger. Each button touch lights up

corresponding row and column LED, indicating the button you are touching. If you

touch more than one button, all the LEDs are turned OFF as multi touch is not

supported.

■To monitor the CapSense parameters refer to readme file on CD/DVD at:

\Firmware\20x34_CSA\PSoC Designer\PD project1\Readme.pdf

6. Design Support and Resources

A wealth of information about PSoC®Designer, and CapSense™ Best Practices is

available on the www.cypress.com web site, and more is frequently added. For

knowledge base articles, customer forums, and online application support, visit

www.cypress.com/go/support.

[+] Feedback

1. Kit Contents

Each CY3280-BMM Universal CapSense™ Matrix Button Module Kit contains:

■CY3280-BMM Universal CapSense Module Board

■CY3280-BMM Universal CapSense Module Board CD/DVD

■CY3280-BMM Quick Start

■1.5 mm Acrylic Overlay with adhesive

Universal CapSense Module boards are available for purchase separately, or as part

of combination kits. Do visit www.cypress.com/shop for more information.

Prerequisites:

■Universal CapSense Controller Board

■PSoC MiniProg

■I2CUSB Bridge

■USB Mini-B Cable

2. Module Hardware

This module is comprised of components and sensors detailed in the following figure.

The module consist of eight CapSense buttons organized in a 4x4 matrix format to

form 16 physical buttons and eight LEDs. These are interfaced to the CapSense

controller board via 44 pin receptacle connector (J1). A three pin jumper (J2) is

provided for selection between shield electrode and ground. The board also

incorporates an optional I2C EEPROM and thermistor that are not populated by

default.

LEDs Optional I2C EEPROM

Footprint (On Reverse Side)

Voltage Test Points

44-Pin CapSense

Connector (J1)

Optional Thermistor

Footprint

(On Reverse Side)

Shield Selection Jumper (J2)

CapSense

Matrix Buttons

Page 2 Page 3

3. Getting Started

The CY3280-BMM board can be used with any of the UCC (Universal CapSense

controller) boards. The example firmware is available on the CD/DVD. Insert the

CY3280-BMM Kit CD/DVD into the CD/DVD drive of your PC, and follow the

instructions on the screen to complete the installation.

4. Setup the Board

This section demonstrates the setup of CY3280-BMM with CY3280-20x34 Universal

CapSense Controller. Similar procedure is used for all UCC boards.

■Connect the CY3280-BMM board to the CY3280-20x34 Universal CapSense

Controller board's P2 receptacle connector.

■In CY3280-20x34 UCC board place shunts on pins 2 and 3 of J1 and pins 1 and 2

of J4.

■In CY3280-BMM board place shunts on pins 2 and 3 of J2.

■Connect your computer to the CY3280-20x34 Universal CapSense Controller

board's ISSP connector (J3) using a PSoC MiniProg and a USB cable.

■Open PSoC Programmer by going to Windows Start > All Programs >

Cypress > PSoC Programming 3.05 > PSoC Programmer.

■Select MiniProg 1 from Port Selection view in the Programmer window.

■Message Successfully Connected to MINIProg…..MINI Version 1.75 appears in

the Actions pane.

Note: If MiniProg Version is older than 1.75, go to Utilities and click on Update

Firmware icon.

■Confirm that the Programming Parameters are as shown in the figure on page 4.

■Click File Load, navigate to, and open the CY3280_20x34_PD_Project1.hex file

on CD/DVD at: \Firmware\HexFiles

■Click the Program icon. After the programming is complete Programming

Succeeded appears in the Actions pane.

D1, D2

[+] Feedback

1. Kit Contents

Each CY3280-BMM Universal CapSense™ Matrix Button Module Kit contains:

■CY3280-BMM Universal CapSense Module Board

■CY3280-BMM Universal CapSense Module Board CD/DVD

■CY3280-BMM Quick Start

■1.5 mm Acrylic Overlay with adhesive

Universal CapSense Module boards are available for purchase separately, or as part

of combination kits. Do visit www.cypress.com/shop for more information.

Prerequisites:

■Universal CapSense Controller Board

■PSoC MiniProg

■I2CUSB Bridge

■USB Mini-B Cable

2. Module Hardware

This module is comprised of components and sensors detailed in the following figure.

The module consist of eight CapSense buttons organized in a 4x4 matrix format to

form 16 physical buttons and eight LEDs. These are interfaced to the CapSense

controller board via 44 pin receptacle connector (J1). A three pin jumper (J2) is

provided for selection between shield electrode and ground. The board also

incorporates an optional I2C EEPROM and thermistor that are not populated by

default.

LEDs Optional I2C EEPROM

Footprint (On Reverse Side)

Voltage Test Points

44-Pin CapSense

Connector (J1)

Optional Thermistor

Footprint

(On Reverse Side)

Shield Selection Jumper (J2)

CapSense

Matrix Buttons

Page 2 Page 3

3. Getting Started

The CY3280-BMM board can be used with any of the UCC (Universal CapSense

controller) boards. The example firmware is available on the CD/DVD. Insert the

CY3280-BMM Kit CD/DVD into the CD/DVD drive of your PC, and follow the

instructions on the screen to complete the installation.

4. Setup the Board

This section demonstrates the setup of CY3280-BMM with CY3280-20x34 Universal

CapSense Controller. Similar procedure is used for all UCC boards.

■Connect the CY3280-BMM board to the CY3280-20x34 Universal CapSense

Controller board's P2 receptacle connector.

■In CY3280-20x34 UCC board place shunts on pins 2 and 3 of J1 and pins 1 and 2

of J4.

■In CY3280-BMM board place shunts on pins 2 and 3 of J2.

■Connect your computer to the CY3280-20x34 Universal CapSense Controller

board's ISSP connector (J3) using a PSoC MiniProg and a USB cable.

■Open PSoC Programmer by going to Windows Start > All Programs >

Cypress > PSoC Programming 3.05 > PSoC Programmer.

■Select MiniProg 1 from Port Selection view in the Programmer window.

■Message Successfully Connected to MINIProg…..MINI Version 1.75 appears in

the Actions pane.

Note: If MiniProg Version is older than 1.75, go to Utilities and click on Update

Firmware icon.

■Confirm that the Programming Parameters are as shown in the figure on page 4.

■Click File Load, navigate to, and open the CY3280_20x34_PD_Project1.hex file

on CD/DVD at: \Firmware\HexFiles

■Click the Program icon. After the programming is complete Programming

Succeeded appears in the Actions pane.

D1, D2

[+] Feedback

CY3280-BMM Universal CapSense™ Matrix

Button Module Kit Quick Start

Doc. # 001-51788 Rev. *A

Cypress Semiconductor

198 Champion Court

San Jose, CA 95134-1709

Phone (USA): 800.858.1810

Phone (Intnl): 408.943.2600

http://www.cypress.com

trademarks, and PSoC®is a registered trademark of Cypress Semiconductor Corp. All other trademarks or

registered trademarks referenced herein are property of the respective corporations.

Cypress Semiconductor Corporation

198 Champion Ct., San Jose, CA 95134 USA

www.cypress.com

If you have questions, call

Cypress Customer Support

+1 (800) 541-4736 Ext. 8 (in the USA),

+1 (408) 943-2600 Ext. 8 (International),

or visit www.cypress.com/go/support

Doc. # 001-51788 Rev. *A

■Click Toggle Device Power button. The Power LEDs D1, D2 on the CY3280-

20x34 UCC board lights up. Corresponding LEDs on other UCC board's lights up.

5. Test the Board

■Touch one button at a time with your finger. Each button touch lights up

corresponding row and column LED, indicating the button you are touching. If you

touch more than one button, all the LEDs are turned OFF as multi touch is not

supported.

■To monitor the CapSense parameters refer to readme file on CD/DVD at:

\Firmware\20x34_CSA\PSoC Designer\PD project1\Readme.pdf

6. Design Support and Resources

A wealth of information about PSoC®Designer, and CapSense™ Best Practices is

available on the www.cypress.com web site, and more is frequently added. For

knowledge base articles, customer forums, and online application support, visit

www.cypress.com/go/support.

[+] Feedback

Other Cypress Control Unit manuals

Cypress

Cypress EZ-BT WICED CYBT-423028-02 User manual

Cypress

Cypress EZ-BLE CYBLE-222014-01 User manual

Cypress

Cypress EZ-BLE PRoC User manual

Cypress

Cypress CYWM6935PAEC User manual

Cypress

Cypress CY8CKIT-019 User manual

Cypress

Cypress EZ-BLE PRoC AN9684 User manual

Cypress

Cypress CapSense Express SmartSense CY3280-MBR2 User manual

Cypress

Cypress EZ-BLE PSoC CYBLE-224116-01 User manual

Cypress

Cypress EZ-BLE PRoC CYBLE-022001-00 User manual

Cypress

Cypress EZ-BT WICED CYBT-343026-01 User manual

Cypress

Cypress EZ-BLE PRoC CYBLE-012011-00 User manual

Cypress

Cypress EZ-BT CYBT-483039-PROG User manual

Cypress

Cypress EZ-BLE PRoC CYBLE-212019-00 User manual

Cypress

Cypress CYW43353 User manual

Cypress

Cypress CapSense Express CY3280-MBR User manual

Cypress

Cypress EZ-BLE PRoC CYBLE-2120 0 Series User manual

Cypress

Cypress EZ-BLE CYBLE-222005-00 User manual

Cypress

Cypress CY4609 User manual

Cypress

Cypress CAPSENSE CY3280-BSM User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual