Cybernet iOne-MP171 User manual
iOne-Medical Panel PC
iOne-MP171
USER’S MANUAL
Copyright©,2008. All rights reserved
All other brand names are registered trademarks of their respective owners.
i
Acknowledgments
Intel® and Core 2 Duo and Core Solo are registered trademarks of
Intel® Corporation.
IBM, PC/AT, PS/2 are trademarks of International Business
Machines Corporation.
Microsoft® Windows is a registered trademark of Microsoft®
Corporation.
RTL is a trademark of Realtek Semi-Conductor Co., Ltd.
C&T is a trademark of Chips and Technologies, Inc.
UMC is a trademark of United Microelectronics Corporation.
ITE is a trademark of Integrated Technology Express, Inc.
VIA is a trademark of VIA Technology, Inc.
Award is a registered trademark of Award Software International,
Inc.
PS/2 is a trademark of International Business Machines
Corporation.
Intel is a trademark or registered trademark of Intel Corporation.
Microsoft Windows is a registered trademark of Microsoft
Corporation.
Winbond is a registered trademark of Winbond Electronics
Corporation.
All other product names or trademarks are properties of their
respective owners.
ii
FCC Class B
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 18 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a residential environment.
This equipment generates, uses and can radiate radio frequency energy. If not
installed and used in accordance with this user manual, itmay cause harmful
interference to radio communications.
Note that even when this equipment is installed and used in accordance with
this user manual, there is still no guarantee that interference will not occur. If this
equipment is believed to be causing harmful interference to radio or television
reception, this can be determined by turning the equipment on and off. If
interference is occurring, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and the receiver
Connect the equipment to a power outlet on a circuit different from that to
which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help
Warning:
Any changes or modifications made to the equipment which are not expressly
approved by the relevant standards authority could void your authority to operate
the equipment.
Caution:
Danger of explosion if battery is incorrectly replaced. Replace only with the same
or equivalent type recommended by the manufacturer. Dispose of used batteries
according
iii
Safety Instructions
Greeting & Setup
Thank you for purchasing the iOne-MP171 unit. We wish that this unit
will be durable and reliable in providing your medical application
needs. Please follow the instructions below to ensure the unit
continues to have high performance.
Unpacking
After opening the carton, there will be a Monitor display unit with an
accessory box. Examine the contents to see if there are damages to
the unit and if all accessories are present.
Setting up
Please read this manual carefully and remember to keep this manual
for future reference.
Safety Instructions & Cleaning
The unit has undergone various tests in order to comply with safety
standards. Inappropriate use of the open frame unit may be
dangerous. Please remember to follow the instructions below to insure
your safety during the installation and operating process.
Transporting & Placement of unit
1. When moving the unit on a cart; be very cautious. Quick stops,
excessive forces and uneven surfaces may cause the cart to overturn
thus risking the unit to fall to the ground.
2. If the Monitor display unit does fall to the ground, immediately turn
the power off and disconnect cords. Then contact a service technician
for repairs. Continual use of the unit may result cause a fire or electric
shock. Also, do not repair the unit on your own.
2. Having two or more people transporting the display unit is
recommended. In addition, when installing the unit by suspending it
also requires two or more people.
iv
3. Before suspending the unit, make sure the material used for
suspension is sturdy and stable. If not properly suspended, the display
unit may fall and cause serious injury to people standing nearby as
well as to the unit itself.
4. If you wish to mount the display unit, remember to use only the
mounting hardware recommended by the manufacturer.
Electrical and Power Source Related
1. This Monitor display unit must operate on a power source as shown
on the specification label. If you are not sure what type of power
supply used in the area, consult your dealer or local power supplier.
2. The power cords must not be damaged. Applied pressure, added
heat, and tugging may damage the power cord.
3. The power cord must be routed properly when setup takes place.
We advise that this aspect measure is to prevent people from stepping
on the cords or while the unit is suspended to prevent flying objects
from getting tangled with the unit.
4. Do not overload the AC outlets or extension cords. Electrical shocks
or fires may occur from overloading.
5. Do not touch the power source during a thunderstorm.
6. If your hands are wet, do not touch the plug.
7. Use your thumb and index finger, grip firmly on the power cord to
disconnect from the electrical socket. By pulling the power cord, may
result in damaging it.
8. If the unit is not going to be in use for an extended period of time,
remember to disconnect the unit.
9. The Monitor display unit uses voltage between 90-264VAC. Connect
the unit to a power source with the same numerical value as shown.
v
Please use only the power cord provided by the dealer to ensure safety
and EMC compliance.
Various Factors of Environment
1. Do not insert objects into the openings.
2. Do not have liquids seep into the internal areas of the Monitor
display unit.
3. Having liquids seep in or inserting objects into the unit may result in
electric shocks from taking and/or short circuiting the internal parts.
4. Do not place the Monitor display unit in the presence of high
moisture areas.
5. Do not install the Monitor display unit in a wet environment.
6. Do not place near unit near heat generating sources.
7. Do not place the unit in a location where it will come in contact with
fumes or steam.
8. Remember to keep the Monitor display unit away from the presence
of dust.
9. If water has flow in or seep in, immediately disconnect the open
frame unit. Then contact a service technician for repairs.
Ventilation Spacing
1. Do not cover or block the openings on the top and back sides of the
display unit. Inadequate ventilation may cause overheating thus
reducing the lifespan of the unit.
2. Unless proper ventilation is present, do not place unit in an enclosed
area; such as a built-in shelf. Keep a minimum distance of 10 cm
between the display unit and wall.
vi
Cleaning the unit
(1) Remember to turn off the power source and to unplug the cord
from the outlet before cleaning the unit.
(2) Carefully dismount the unit or bring the unit down from suspension
to clean.
(3) Please use a dry soft cloth to clean the unit.
(4) Take a dry cloth and wipe the unit dry. Remember to avoid having
liquids seep into the internal components and areas of the Monitor
display unit.
Servicing, Repairing, Maintenance & Safety Checks
1. If the unit is not functioning properly, observe the performance level
of the display closely to determine what type of servicing is needed.
2. Do not attempt to repair the Monitor display unit on your own.
Disassembling the cover exposes users’ to high voltages and other
dangerous conditions. Notify and request a qualified service technician
for servicing the unit.
3. If any of the following situations occur turn the power source off and
unplug the unit. Then contact a qualified service technician
(a) A liquid was spilled on the unit or objects have fallen into the
unit.
(b) The unit is soaked with liquids.
(c) The unit is dropped or damaged.
(d) If smoke or strange odor is flowing out of the operating unit.
(e) If the power cord or plug is damaged.
(f) When the functions of the unit are dysfunctional.
4. When replacement parts are needed for the Monitor display unit,
make sure service technicians use replacement parts specified by the
manufacturer, or those with the same characteristics and performance
as the original parts. If unauthorized parts are used it may result in
starting a fire, electrical shock and/or other dangers.
vii
viii
Caution:
DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED ENVIRONMENT
WHERE THE STORAGE TEMPERATURE IS BELOW -20° C (-4° F) OR
ABOVE 60° C (140° F). THIS MAY DAMAGE THE EQUIPMENT.
This equipment shall not be used in life support systems.
The user is not to touch SIP/SOPs and the patient at the same time.
The sound pressure level at the operator’s position according to IEC
704-1:1982 is no more than 70dB (A).
Contact information:
Address: 5 Holland, Bldg. 201
Irvine, CA 92618
U.S.A.
TEL: (888) 834-4577
E-Mail: sales@cybernetman.com
Table of Contents
A
CKNOWLEDGMENTS
....................................................................................
I
FCC
C
LASS
B..................................................................................................
II
S
AFETY
I
NSTRUCTIONS
.............................................................................
III
INTRODUCTION
.......................................................................................... 1
P
RODUCT
D
ESCRIPTION
................................................................................. 1
P
ACKAGE LIST
.................................................................................................. 2
F
EATURES
........................................................................................................ 3
S
PECIFICATIONS
............................................................................................. 4
C
LEANING
/D
ISINFECTING
.............................................................................. 7
D
IMENSION
...................................................................................................... 8
S
YSTEM
V
IEW
.................................................................................................. 9
D
ISCONNECT
D
EVICE
................................................................................... 12
BIOS SETUP
................................................................................................ 13
APPENDIX
A. GPIO UNCTION ................................................................................ A
B. VESA MOUNTING ............................................................................B
C. SCRAP COMPUTER RECYCLING ..................................................C
Table of contents
Other Cybernet Touch Panel manuals
Popular Touch Panel manuals by other brands
IBASE Technology
IBASE Technology ASTUT-152-RE1S user manual
YASKAWA
YASKAWA TP 610C manual
B&R
B&R Power Panel C Series user manual
Beijer Electronics
Beijer Electronics X2 control Hardware and installation manual
AXIOMTEK
AXIOMTEK GOT321W-521 user manual
TRIDONIC.ATCO
TRIDONIC.ATCO x-touchBOX Operation manual
