CUBEX MARK II Series User manual

INSTRUCTIONS: CUBEX - MARK II Series

Cubex Co., Inc. 06-03 Rev 9

CUBEX

Quad Antennas

MK II – PT3

MK II – PT5

Safety warning

Please read through these instructions completely before starting

your installation.

Antenna work is dangerous. Always wear an OSHA approved

safety harness with the appropriate nylon or wire rope safety

lanyards to protect yourself and your helpers from falls. Also all

helpers on the ground should be wearing hard hats to protect them

from falling objects such as tools etc.

Cubex Co., Inc. has no control over the conditions at the antenna site and therefore can not be

held responsible for any damage or injury to persons or property.

If for any reason you do not understand any part of these instructions, or your installation

is different and these instructions do not pertain to your situation. Do not hesitate to call

Cubex Co., Inc. for assistance at (561) 748-2830

Note: Take precautions when handling and further processing fiberglass material. It

is recommended that gloves be used when working with this material.

Price: $ 4.95 US

Instructions:Cubex - MARK II Series

Cubex Co., Inc. 06-03 Rev 9

Pg. 2

A S S E M B L Y I N S T R U C T I 0 N S

The CUBEX MK II PT 3 and 5 Band QUAD ANTENNA

FOREWORD: The CUBEX MK II is a pre-tuned Quad Antenna. All elements are factory

measured and under normal conditions should not require adjustment. Elements are designed

for operation in the center of each band. Should one wish to favor the low or high end of one or

more bands, limited “tuning”, is provided for at Note 2 at the end of the Instructions. It is

recommended that the assembly Instructions be read completely prior to starting Installation.

1. Begin antenna assembly by laying one of the “spider” castings on the ground with the

“trough” facing upward. Place the butt ends of four spreader arms in the spider troughs. BE

SURE the arms are all similar (Driven Element or Reflector). Fasten each spreader arm to its

respective casting arm using two “gear” driven clamps on each arm. One clamp is located

near the butt of the arm and is positioned between the two guides on the outer face of the

casting. The other clamp is positioned near the end of the casting arm in the depression

provided for it. The gear driven clamps are assembled and tightened by hand using a

screwdriver. With the screw head facing upward, loop the strap around the arm, positioning

the adjustment screw next to the arm and tighten slightly.

Final permanent tightening should be done at the very end of the wire element assembly after

everything has been positioned properly. The same procedure is followed for the remaining

assemblies.

2. Select the 10 METER DRIVEN ELEMENT, remove only the Twist Ties and carefully uncoil

and gently straighten the element (Use similar technique for all elements). This will permit the

element wire bundle to be laid out straight in preparation for stringing through the spreader

arms.

3. The stringing procedure is illustrated by Figure 3 and there will be less of a tendency to

tangle if this procedure is followed closely.

As the wire element is unfolded, carefully remove the tape and straighten the “bends” enough

to allow passage through the holes drilled in the spreader arms, but try and retain enough of

the kink so that it can later be centered in each respective arm for the purpose of maintaining a

uniformly square structure configuration.

The 10 meter elements are strung through the first set of holes nearest the butt end of the

arms; 12 meter next (optional) 15 meter elements near the center of the arms; then 17 meter

(optional) and finally the 20 meter elements near the tips of the arms. BE SURE that Driven

Element wires are used with Driven Element ARMS, Reflector wires with Reflector ARMS.

The wire ends of all DRIVEN ELEMENTS are terminated at a special DRIVEN ELEMENT

TERMINAL BLOCK as shown In Figure 1. (Separate terminal block for each band) or at the

CUBEX MATCHING TRANSFORMER (optional item).

Instructions:Cubex - MARK II Series

Cubex Co., Inc. 06-03 Rev 9

Pg. 3

If one wishes to assemble the antenna for operation with the Cubex Matching

Transformer, it is recommended that the 15 meter DRIVEN ELEMENT be strung

first and loosely linking the driven element ends together. The 1O and 20 meter

wires are then brought to the same point as they are installed. (Note, If used, the 12

and 17 meter wires can then be added). The transformer can then be installed at

the 15m point and the various driven elements positioned and tensioned

appropriately.

The wire element ends of the 20 meter and 10 meter DRIVEN ELEMENTS have extra long

“fold backs”. These provide the slight added length needed for attachment to the Cubex

Matching Transformer. When all DRIVEN ELEMENTS are terminated separately, this excess

fold back is simply trimmed off and discarded.

3. For REFLECTOR assembly, the procedure is the same as step 2 except that the wire

element ends are simply brought together at the “end kinks”, spliced (recommend “lineman’s

splice” and soldered.

After the 2 element assemblies (Driven and Reflector) have been completed, the boom should

be temporarily supported on a 9 to 10 foot step ladder or lashed to the side of a tower at a

height which will permit the bottom element wires to clear the ground.

WARNING - THE CUBEX SPIDERS HAVE BEEN PRE-SPREAD USING A

MICROMETER FOR PRECISE MEASUREMENT. TO FORCE THE UNITS OPEN PAST

THE ALREADY PRE-DEFINED LIMITS WILL RESULT IN BREAKAGE OF THE CAST

UNITS.

4. The REFLECTOR assembly, is placed at the end of the boom and the DRIVEN

ELEMENT is placed at the other end of the boom. (8 ft. on standard boom, and 12 ft.

separation on Long Boom option) After the assemblies are in place on the boom they should

be rotated and aligned so that all bottom element wires are parallel to the ground.

Place the BOOM/MAST COUPLER (cast or alum. plate) at the center of the boom. Fasten the

coupler to the boom using the supplied bolts. 2” OD booms require 2 - 2”x5/16” U-bolts with

the HD 3” O.D. boom option requiring 4 - 3”x3/8” U bolts. All U-bolts are secured using, nuts

and lock washers. The bolts should be tightened on the boom sufficiently to preventing rotation

of either with respect to the other.

5. As an aid to lifting the array, an 8 to 10 foot pole or pipe section (GIN POLE) may be

temporarily secured to the mast or tower. The Gin Pole is a pole or pipe that has a small pulley

at the top. Using a strong rope the antenna can be pulled up to the final mounting position by

an assistant with little danger to the tower climber. This will usually facilitate getting the array

up to the top of tower, mast, etc.

The antenna array is then lifted into place on the tower and the boom/mast coupler plate is

secured to the mast using the supplied hardware. The antenna & boom assembly is bolted to

the mast using the supplied U-bolts 2” or 3”. REMINDER: DON’T TAKE CHANCES. USE A

CLIMBING BELT OR SAFETY HARNESS WHILE ON A TOWER. THE LIFE YOU SAVE

COULD BE YOURS!

Instructions:Cubex - MARK II Series

Cubex Co., Inc. 06-03 Rev 9

Pg. 4

CAUTION; While every effort has been made in designing and fabricating both the spreader

arms and the spiders for maximum strength, it is possible to suffer breakage if the assembly is

dropped or impacted against buildings, trees, etc., Use care in handling.

6. FEEDING THE, 2 ELEMENT QUAD. The feed-point impedance’s of this antenna will

vary with each band. Twenty meters is about 50 ohms, Fifteen meters = 75 ohms and Ten

meters is about 110 ohms. The CUBEX matching transformer is a combination unbalanced to

balanced and impedance transformation device. It will allow for single feed line with

acceptable SWR while using 3 or 5 bands of operation.

An alternative method of feeding the multi band quad utilizes a remote antenna switch such as

the AMERITRON RCS-8V. When using the remote antenna switch or separate feed lines for

each band it will be necessary to fabricate Co-Ax matching sections from 75 ohm RG11U

cable. These must be an “Odd” one-quarter wavelength to function properly (1,3,5, ,etc.).

For 10 meters use69 inches of RG/11U attached to 10 -meter DRVN. EL. FEED POINT and

any length of RG8/U from the other end of the RG/11U to the transmitter.

For 15 meters, use92 inches of RG/11U attached to the 15-meter DRVN. EL. FEED POINT

and any length of RG8/U from other end of RGII/U to the transmitter.

Any excess cable can be coiled (6” dia.) and taped together.

See Table I on the following page for dimensions of linear matching sections.

NOTE: In some situations it maybe be better to make a 3/4 wave (207 in) 75 ohm 10 m

stub. Any excess cable should be wrapped and taped into a 6” coil.

Where a REMOTE SWITCHING SYSTEM is used, one would position the remote unit at a

point on the boom where both 10 and 15 meter matching sections could terminate at the box.

This would eliminate splicing of cables, Baluns are generally not needed and have proven

effective in only a small percentage of unusual situations. Fortunately, the great majority of

quad installations perform very satisfactorily without the need to resort tocomplicated

matching systems, but in an occasional "rare" case of difficulty, the Gamma Match (either

individual or Tri-Gamma) has proven to be a good solution. For Gamma Match information

see “Old Notes” at end of instructions.

The CUBEX matching transformer is an excellent choice for matching the antenna system to

the transceiver. It is rated at 1.5kw PEP and allows for a single FEED LINE and matches the

CUBEX antenna without the hassle of complicated matching networks.

Good luck and DX –

Instructions:Cubex - MARK II Series

Cubex Co., Inc. 06-03 Rev 9

Pg. 5

Note: These terminals are not supplied when Cubex Matching Transformer is ordered with Antenna.

Matching Stub dimensions: Table I

Electrical Quarter wave 75 ohm coax ; velocity factor = 0.67

BAND CABLE TYPE LENGTH (IN.) LENGTH (CM)

10 Meters RG11/U 75 ohm 69 in

(3/4 w-17’-3”) 175.25 cm

(5.2575m)

12 Meters RG11/U 79-9 ½” in

(3/4w=19’-11”) 202.74 cm

(6.082m)

15 Meters RG11/U 92 in.

(3/4w=23’-0”) 233.68 cm

(7.01m)

17 Meters Note 3

20 Meters RG 8/U 50 ohm Any length

40 Meters RG11/U 23.35 ft (420 in) 7.1171 m

Note 1- that any length 50 ohm coax maybe connected to the end of these matching stubs.

Note 2- Some experimentation may be required in adjusting each matching stub to optimize the

impedance transformation.

Note 3- 17 meters should not require any stub and match okay with 50 ohm cable.

Note - Cables supplied by Cubex may vary in length (longer) from above as we use a special

RG-11 coaxial cable with a VF of 0.72

Dimensions above

Figure I

Instructions:Cubex - MARK II Series

Cubex Co., Inc. 06-03 Rev 9

Pg. 6

QUAD LOOP DIMENSIONS:

BAND 10M 12M 15M 17M 20M

Reflector

Driven Ele.

Purposely left blank – Use to record specific data as assembled.

20m

17m

15m

12m

10m

Location of Cubex

Matching

Transformer when

used.

6" dia Coil

Excess

Cable

Boo

Mast

Antenn

Instructions:Cubex - MARK II Series

Cubex Co., Inc. 06-03 Rev 9

Pg. 7

Truss guying of the boom is advisable when using2 inch boom material in lengths greater than

8 feet. Heavy duty booms (2” x 0.125) do not require the bridge truss arrangement.

A good grade of non-metalic outdoor grade nylon or dacron line may be used. (Cubex Dacron

Antenna Rope is ideal and supplied with our larger antennas).

2” Boom to Mast

Mounting Plate

Instructions:Cubex - MARK II Series

Cubex Co., Inc. 06-03 Rev 9

Pg. 8

Stranded Wire Element Preparation

CAUTION: Working with stranded antenna wire certain precautions are required. First to

prevent wire strands from unraveling when cutting to proper lengths it is important to flow

solder about ½” either side of the cut point. Becareful as the wires may be very hot after

soldering.

The second caution comes when un-spooling the wire to the necessary lengths. It is

recommended that the wire be “unrolled” from the roll and not “stripped”, as this will accentuate

the spiral wrap tendency leading to wire kinks. Always be on the watch for wire kinks forming

and take appropriate action to prevent them. If one should occur, it may be recoverable by

carefully straightening it while smoothing.

Wire Element Support - "Wire Wrap"

After feeding the element wire through the spreader arm holes, and checking for arm

alignment, the "wire wrap" should be applied. This following procedure will assure minimum

flexing of the element wire at the arm attachment point and to maintain element/spreader arm

alignment we recommend securing all 20 meter and 17 meter element arm attachment points

in the following manner. Generally speaking 15, 12 or 10 meter elements will not need this

treatment. Sufficient "Wire Wrap" wire has been provided for this procedure - follow the

diagram below.

Wire

Element

1 or 2 snug wraps

around the

spreader Arm

START

4 turns around element

wire - spread over

about 1-1/2" SPREADER

ARM

FINISH

4 turns around element wire -

spread over about 1-1/2"

Instructions:Cubex - MARK II Series

Cubex Co., Inc. 06-03 Rev 9

Pg. 9

Additional Notes on feeding:

Separate lines are to be preferred over the simplified “Single FEED LINE” method to a

common junction point of elements. This is not to say that the “SF” system is unacceptable,

but one must be prepared to accept some SWR compromise when using it If difficulty is

encountered in LOADING and/or SWR with either system.

FEED LINE PRUNING should be attempted as the NUMBER ONE approach when using

the “SF” approach.

Baluns are generally not needed and have proven effective in only a small percentage of

unusually rough situations. Fortunately, the great majority of quad installations perform very

satisfactorily without the need to resort tocomplicated matching systems, but in an

occasional "rare" case of difficulty, the Gamma Match (either individual or Tri-Gamma) has

proven to be a good solution. For Gamma Match information see historical notes at end of

instructions, or refer to Bill Orr’s book on Quads.

Fig. 3a

Alternate method-Line Splice

Reflector / Director

Connections - splice

or crimp sleeve

Locate the small bag of crimp sleeves (5 +1spare).

After completing the wiring of the Reflector and Director elements the ends must be connected to

complete the Quad loop. Slide both ends through the sleeve as shown in fig 3b. Pull wire through

to eliminate the slack in the wire. Temporarily fold each wire end as above to hold the wire

position. Check the tension in all of the sides of this element, making sure that the arms are

"square" and in line. Make an adjustment at the sleeve and if satisfied Crimp, or solder the element

wire into the sleeve. This technique allows you to get the element wire tension correct without

committing to a wire wrap or crimped connection.

Trim wire ends after

completing adjustment of

tension

Pull wires through sleeve and bend to

temporarily hold position

"Line men's" Splice

Connecting Element Wires -

Fig. 3b

Crimp Splice

Instructions:Cubex - MARK II Series

Cubex Co., Inc. 06-03 Rev 9

Pg. 10

Cubex Engineering

2 ELEMENT QUAD DIMENSIONS (PER SIDE)

10 M 12M 15M 17M 20MBAND Inches CM Inches CM Inches CM Inches CM Inches CM

Reflector 107.50 273.05 124.00 314.96 145.00 368.30 170.50 433.07 218.00 553.72

Driven El 105.00 266.70 120.75 306.71 142.00 360.68 166.50 422.91 212.00 538.48

ARM DRILLING DIMENSIONS

REFLECTOR:

|BUTT END

|-------------- 10M --------- 74-3/8” (188.91cm) ---------------------->

|-------------- 12M --------- 85-1/2” (217.17cm) ------------------------------>

|-------------- 15M --------- 101-0” (256.54 cm) -------------------------------------------->

|-------------- 17M ---------118 1/2” (301cm) ----------------------------------------------------->

|-------------- 20M --------- 152-5/8” (387.67cm) -------------------------------------------------------->

DRIVEN ELEMENT:

BUTT END

|-------------- 10M --------- 72-3/8” (183.83 cm) ------------------------->

|-------------- 12M --------- 83-3/8” (211.77 cm) ---------------------------------->

|-------------- 15M --------- 98-1/2” (250.19 cm) ------------------------------------------>

|-------------- 17M ---------115-1/2” (293.37 cm) ---------------------------------------------->

|-------------- 20M --------- 148-3/8” (376.87 cm) ----------------------------------------------------->

NOTE:

These dimensions are for reference only, actual dimensions may vary slightly from those above in actual

practice.

This manual suits for next models

Other CUBEX Antenna manuals

CUBEX

CUBEX SkyMaster Series User manual

Popular Antenna manuals by other brands

Alfa Network

Alfa Network APA-L01 Specifications

Naval

Naval PR-422CA Operation manual

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series manual

TERK Technologies

TERK Technologies TV44 owner's manual

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK quick start guide

HP J8999A instructions

MobilSat

MobilSat MSP-S Mounting instructions

Steren

Steren ANT-UHF 13 instruction manual

Novatel

Novatel 600-G User information

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna owner's manual

TRENDnet

TRENDnet TEW-AO12O Specifications

Radio Shack

Radio Shack 15-1837 owner's manual

CommScope

CommScope CMAX-OMFX-43M-I53 Installation instruction

Ramsey Electronics

Ramsey Electronics DAP25 Kit assembly and instruction manual

COBHAM

COBHAM SAILOR 800 VSAT Replacement procedure

Trango Systems

Trango Systems AD900-9 Specification sheet

Steren

Steren ANT-100 user manual

Proxim

Proxim 5054-PA-23 quick start guide