CRT MICRON U/V User manual
A1.170630
User Manual
Dual band transceiver
144-146 MHz RX/TX 430-440 MHz RX/TX
7
The CRT MICRON UV HAM was approved in the followed countries that implement the CEPT regulation TR
61/01
AT,BE,BG,CH,CY,CZ,DE,DK,EE,FI,FR,GR,HR,HU,IE,IS,IT,LI,LT,LU,LV,MT,NL,NO,PL,PT,RO,SE,SI,SK,UK. ES
Please carefully read the instructions
Information on recycling, not throwing your material in the trash at the end of life,
Bring it to special aera to be recycling
DC using
Keep dry
Shield symbol
CE conformity symbol
Warning
STORAGE , TRANSPORT, USING
Storage : Classe 1 -30/85% (° Humidity)
Transport :- 30/85% (° Humidity )
operating temperature –30 à + 50°
Using cycle TX 10%/RX 90%
CONTENTS
1.FUNCTIONS & FEATURES........................................................................... 1
2.ACCESSORIES ............................................................................................. 2
3.INITIAL INSTALLATION ................................................................................ 3
4.GETTING ACQUAINTED............................................................................... 8
5.WORKING MODE........................................................................................ 11
6.BASIC OPERATIONS.................................................................................. 12
7.FUNCTION MENU ....................................................................................... 11
8.CHANNEL MENU ........................................................................................ 20
9.KEYPAD MENU SETUP .............................................................................. 23
10.PROGRAMMING SOFTWARE .................................................................. 24
11.MAINTENANCE ......................................................................................... 25
12.SPECIFICATIONS...................................................................................... 26
13.ATTACHED CHART................................................................................... 27
1
1. FUNCTIONS & FEATURES
♦Adopt superior quality material, better technology and high quality radiator to
ensure stable and durable operation;
♦180 degree rotatable TFT LCD display;
♦Full alloy body for heat radiation;
♦Amateur mode and professional mode for different operation requirement;
♦Distribute buttons reasonably, convenient for operation;
♦Separate band width setting for each single channel, Wide 25K, Middle band
20K, Narrow band 12.5K;
♦ 200 programmable memory channels, identied by editing name;
♦Separate CTCSS, DCS setting for each single channel, rejecting extra calling
from other radios;
♦Various scan functions including CTCSS/DCS Scan function;
♦Smart menu control and PC programming control;
♦Voltage level protection;
♦LCD brightless control;
♦Automatic power on function;
♦Main unit and microphone key lock function.
CRT MICRON Mobile Radio has nice housing, stoutness & stability, advanced
and reliable functions, perfect & valuable. This amateur mobile radio especially
designs for drivers and it pursues philosophy of innovation and practicality. More
functions as follows:
2
2. ACCESSORIES
External SpeakerPC cable
Regulated Power Supply Programming Software Car Antenna
Transceiver Microphone
Adjusting screws
DC Power Cable
with Fuse Holder
Mobile Bracket
Fuse(10A 250V)
MIC
P1 FUNC
P4
P5
P6
P2
P3
2.1 Standard Accessories
2.2 Optional Accessories
manual
3
3. INITIAL INSTALLATION
To install the transceiver, select a safe, convenient location inside your vehicle that
minimizes danger to your passengers and yourself while the vehicle is in motion. Consider
installing the unit at an appropriate position so that knees or legs will not strike it during
sudden braking of your vehicle. Try to pick a well ventilated location that is shielded from
direct sunlight.
1.Install the mounting bracket in the vehicle using the supplied selftapping screws (2pcs)
and at washers (2pcs)
2.Position the transceiver, then insert and tighten the supplied hexagon SEMS screws.
♦Double check that all screws are tightened to prevent vehicle vibration from loosening
the bracket or transceiver.
Car body
Washer (M5)
Tapping screw
(M5x20mm)
Mounting bracket
3.1 Mobile Installation
3.2 DC Power Cable Connection
»Locate the power input connector as close to the transceiver as possible.
3.2.1 Mobile Operation
The vehicle battery must have a nominal rating of 12V. Never connect the transceiver to
a 24V battery. Be sure to use a 12V vehicle battery that has sufcient current capacity. If
the current to the transceiver is insufcient, the display may darken during transmission,
or transmitting output power may drop excessively.
4
3.2.2 Fixed Station Operation
In order to use this transceiver for xed station operation, you will need a separate 13.8V
DC power supply (not included), power supply( QRP-01) as optional accessories. Please
contact local dealer to require.
The recommended current capacity of your power supply is 12A.
1.Connect the DC power cable to the regulated DC power supply and ensure that the
polarities are correct. (Red: positive, Black: negative).
♦Do not directly connect the transceiver to an AC outlet.
♦Use the supplied DC power cable to connect the transceiver to a regulated power
supply.
♦Do not substitute a cable with smaller gauge wires.
1.Route the DC power cable supplied with the transceiver directly to the vehicle's battery
terminals using the shortest path from the transceiver.
♦We recommend you do not use the cigarette lighter socket as some cigarette lighter
sockets introduce an unacceptable voltage drop.
♦The entire length of the cable must be dressed so it is isolated from heat, moisture,
and the engine secondary (high voltage) ignition system/ cables.
2. After installing cable, in order to avoid the risk of damp, please use heat-resistant tap to
tie together with fuse box. Don't forget to reinforce whole cable.
3.In order to avoid the risk of short circuit, please cut down connection with negative (-) of
battery, then connect with radio.
4.Confirm the correct polarity of the connections, then attach the power cable to the
battery terminals; red connects to the positive (+) terminal and black connects to the
negative (-) terminal.
♦Use the full length of the cable without cutting off excess even if the cable is longer
than required. In particular, never remove the fuse holders from the cable.
5. Reconnect any wiring removed from the negative terminal.
6. Connect the DC power cable to the transceiver's power supply connector.
♦ Press the connectors rmly together until the locking tab clicks.
Red
Black
Table of contents
Other CRT Transceiver manuals
