Crestron HD-MD6X2-4K-E Owner's manual

HD-MD6X2-4K-E/HD-MD4X2-4K-E/

HD-MD4X1-4K-E

4K HDMI®Switchers

Supplemental Guide

Crestron Electronics, Inc.

The product warranty can be found at www.crestron.com/warranty.

The specific patents that cover Crestron products are listed at patents.crestron.com.

Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource.

Crestron, the Crestron logo, and DigitalMedia are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States

and/or other countries. HDMI, the HDMI logo, and High Definition Multimedia Interface are either trademarks or registered trademarks of

HDMI Licensing LLC in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in

this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the

marks and names of others. Crestron is not responsible for errors in typography or photography.

This document was written by the Technical Publications department at Crestron.

Supplemental Guide – DOC. 7761A Contents

•

Contents

Introduction 1

Using the Web Interface 1

Accessing the Web Interface................................................................................... 1

Logging In to a Switcher ............................................................................ 2

Navigating the Web Interface ..................................................................... 3

Viewing Status Information...................................................................................... 4

Configuring Routes ................................................................................................. 5

Configuring Input Settings ....................................................................................... 6

Configuring Output Settings .................................................................................... 8

Configuring Network Settings................................................................................ 10

Configuring Device Settings .................................................................................. 11

Enabling or Disabling the Front Panel....................................................... 11

Changing the Username and Password ................................................... 12

Upgrading Firmware................................................................................. 13

Using the Front Panel OLED Display 14

Accessing and Navigating the OLED Display Menu............................................... 14

Configuring Input Settings ..................................................................................... 15

Configuring Output Settings .................................................................................. 18

Configuring Network Settings................................................................................ 19

Configuring Device Settings .................................................................................. 20

Using the Routing Push Buttons 21

Routing Inputs on the HD-MD6X2-4K-E and HD-MD4X2-4K-E ............................ 21

Routing Inputs on the HD-MD4X1-4K-E................................................................ 22

Supplemental Guide – DOC. 7761A HD-MD-6X2/4X2/4X1-4K-E: 4K HDMI Switchers

•

HD-MD6X2-4K-2/HD-MD4X2-4K-E/

HD-MD4X1-4K-E:

4K HDMI®Switchers

Introduction

The Crestron®HD-MD6X2-4K-E, HD-MD4X2-4K-E, and HD-MD4X1-4K-E are 4K HDMI®

switchers. Each switcher supports high-resolution signals up to 4K/60 and provides

advanced DigitalMedia™ EDID management, native Crestron control via Ethernet, a built-in

web server, and a front panel OLED (organic light-emitting diode) display.

While similar in functionality, the switchers differ in the number of HDMI inputs and outputs:

•The HD-MD6X2-4K-E provides six HDMI inputs and two independent HDMI

outputs.

•The HD-MD4X2-4K-E provides four HDMI inputs and two independent HDMI

outputs.

•The HD-MD4X1-4K-E provides four HDMI inputs and one HDMI output.

This guide provides information about configuration of the switchers using the web

interface and the front panel OLED display. Information about the routing push buttons

is also provided. For additional information about the switchers, refer to the

HD-MD6X2-4K-E/HD-MD4X2-4K-E/HD-MD4X1-4K-E DO Guide (Doc.7760).

Using the Web Interface

Built-in web pages of the HD-MD6X2-4K-E, HD-MD4X2-4K-E, and HD-MD4X1-4K-E allow

configuration of routing, input, output, network, and device settings. In addition, information

about the switchers can be viewed.

Accessing the Web Interface

To access the web interface, do the following:

1. Note the IP address that appears on the front panel OLED display.

NOTE:

After power is applied to a switcher, the IP address appears on the front

panel OLED display.

•

HD-MD-6X2/4X2/4X1-4K-E: 4K HDMI Switchers Supplemental Guide – DOC. 7761A

2. Open a web browser.

3. Go to the IP address of the switcher.

The Login page opens. For login information, refer to “Logging In to a Switcher”

below.

Logging In to a Switcher

The Login page allows access to the web interface of a switcher.

To log in to a switcher, do the following:

1. Enter the username and password. The default username is admin, and the default

password is admin.

NOTE:

The username and password are case sensitive.

NOTE:

For enhanced security, it is recommended that the default username and

password be changed. For information about changing the username and

password, refer to “Changing the Username and Password” on page 12.

2. Click the

Submit

button.

The Status page opens. For information about navigating the web interface, refer to

“Navigating the Web Interface” on the following page.

Supplemental Guide – DOC. 7761A HD-MD-6X2/4X2/4X1-4K-E: 4K HDMI Switchers

•

Navigating the Web Interface

The web interface provides a navigation bar and built-in web pages of the switchers.

Web Interface (Sample Status Page of HD-MD6X2-4K-E Shown)

The navigation bar provides access to the web pages as follows:

•Clicking

STATUS

accesses the Status page, which provides general information

about a switcher as well as network-related information. For additional information,

refer to “Viewing Status Information” on the following page.

•Clicking

ROUTING

accesses the Routing page, which allows routes to be set on a

switcher. For additional information, refer to “Configuring Routes” on page 5.

•Clicking

INPUTS

accesses the Input page, which allows the desired EDID to be

sent to the inputs. For additional information, refer to “Configuring Input Settings”

on page 6.

•Clicking

OUTPUT

accesses the Output page, which allows the selection of an input

for routing to an output. For additional information, refer to “Configuring Output

Settings” on page 8.

•Clicking

NETWORK

accesses the Network page, which allows network settings

such as hostname and DHCP (Dynamic Host Configuration Protocol) mode to be

set. For additional information, refer to “Configuring Network Settings” on page 10.

•Clicking

DEVICE

accesses the Device page, which allows changes to username

and password settings and also controls various device functions. For additional

information, refer to “Configuring Device Settings” on page 11.

NOTE:

After 10 minutes of inactivity, the web interface times out and returns to the

•

HD-MD-6X2/4X2/4X1-4K-E: 4K HDMI Switchers Supplemental Guide – DOC. 7761A

Viewing Status Information

General information, such as model name, serial number, and firmware version of a

switcher, can be viewed. The current network settings, such as hostname and IP address,

can also be viewed.

To view status information, do the following: In the navigation bar, click

STATUS

The Status page opens.

NOT

The Status page opens after logging in to a switcher.

Sample Status Page

The Status page displays the following information about a switcher:

•General information, which consists of the following:

oModel (HD-MD6x2-4K-E, HD-MD4x2-4K-E, or HD-MD4x2-4K-E)

oSerial Number

oFirmware Version

•Network-related information, which consists of the following:

oHostname

NOTE:

In the sample Status page shown on the previous page for the

HD-MD6X2-4K-E, the default hostname is

HDMD6X2-6200F1

, where

6200F1

consists of the last six digits of the MAC address of the

HD-MD6X2-4K-E.

oIP Address

oSubnet Mask

oDefault Gateway

oMAC Address

Supplemental Guide – DOC. 7761A HD-MD-6X2/4X2/4X1-4K-E: 4K HDMI Switchers

•

Configuring Routes

Routes can be set so that an HDMI signal from any input on a switcher can be routed to any HDMI

output on the switcher.

•The HD-MD6X2-4K-E allows any of the six inputs to be routed to up to two

independent outputs simultaneously.

•The HD-MD4X2-4K-E allows any of the four inputs to be routed to up to two

independent outputs simultaneously.

•The HD-MD4X1-4K-E allows any of the four inputs to be routed to a single output.

To route the desired inputs to one or more HDMI outputs, do the following:

1. In the navigation bar, click

ROUTING

. The Routing page opens.

Routing Page ( HD-MD6X2-4K-E Page Shown)

As shown above, the Routing page provides a list of inputs and a list of outputs.

NOTE:

The Routing page varies depending on the model of the switcher.

The Routing page shown above applies to the HD-MD6X2-4K-E, which has six

inputs and two outputs. For the HD-MD4X2-4K-E, the Routing page lists four

inputs and two outputs. For the HD-MD4X1-4K-E, the Routing page lists four

inputs and one output.

The default names of the HDMI inputs are

INPUT1,

INPUT2

INPUT3

INPUT4,

INPUT5

(HD-MD6X2-4K-E only), and

INPUT6

(HD-MD6X2-4K-E only). For the

HD-MD6X2-4K-E and HD-MD4X2-4K-E, the default names of the HDMI outputs

are

OUTPUT1

and

OUTPUT2

. For the HD-MD4X1-4K-E, the default name of the

HDMI output is

OUTPUT

2. In the text entry boxes for the inputs and outputs, rename the inputs and outputs if

desired, and then click the

Save Names

button.

3. To route an input to an output, select the corresponding output radio button for the

input. The input is routed to the output immediately.

•

HD-MD-6X2/4X2/4X1-4K-E: 4K HDMI Switchers Supplemental Guide – DOC. 7761A

NOTE:

For the HD-MD6X2-4K-E and HD-MD4X2-4K-E, two output radio buttons

can be selected for a single input if desired.

NOTE:

For each output, the resolution and frame rate being transmitted to the

output are displayed. If the input resolution is changed, the resolution and frame

rate are updated dynamically. If no source is detected, the message

No Source

displayed.

4. (Applicable to the HD-MD4X1-4K-E only) Enable or disable automatic routing:

•To enable automatic routing, click the

TRUE

radio button if it is not already

selected. By default, the

TRUE

radio button is selected.

•To disable automatic routing, click the

FALSE

radio button.

To disconnect a route for an input, click the

radio button for the

corresponding output.

Configuring Input Settings

The desired EDID can be selected and sent to the inputs. Built-in EDID files are available for

selection, and custom EDID files can also be selected. The EDID can be selected on a

global basis and sent to all inputs, or it can be selected on an individual basis for each input.

In addition, inputs can be renamed. HDCP (High-bandwidth Digital Content Protection)

support can also be enabled or disabled for each input on an individual basis.

To send the desired EDID to the inputs, do the following:

1. In the navigation bar, click

INPUTS

. The Input page opens.

Input Page (HD-MD6X2-4K-E Page Shown)

NOTE:

The Input page varies depending on the model of the switcher. The Input

page shown above applies to the HD-MD6X2-4K-E, which has six inputs. For the

HD-MD4X2-4K-E and the HD-MD4X1-4K-E, the Input page lists four inputs.

Other manuals for HD-MD6X2-4K-E

This manual suits for next models

Table of contents

Other Crestron Switch manuals

Crestron

Crestron DIN-HUB User manual

Crestron

Crestron CLW-SLVS1W User manual

Crestron

Crestron CEN-SWPOE-16 User manual

Crestron

Crestron infiNET CLW-SLVS1RF User manual

Crestron

Crestron DM Lite HD-RX-4K-510-C-E User manual

Crestron

Crestron Sonnex SWE-8 User manual

Crestron

Crestron DM-MD8X1-4K-C User manual

Crestron

Crestron DigitalMedia DM-MD8X8-CPU3 User manual

Crestron

Crestron 8x8 DigitalMedia DM-MD8X8 User manual

Crestron

Crestron DIN-8SW8-I User manual

Crestron

Crestron DigitalMedia DM-MD8X8-CPU3 User manual

Crestron

Crestron DigitalMedia DM-MD64X64 Dimensional drawing

Crestron

Crestron CEN-SW-POE-5 User manual

Crestron

Crestron Prodigy P-LSWEX User manual

Crestron

Crestron CNXHUB User manual

Crestron

Crestron CNLGE-8 User manual

Crestron

Crestron HD-TX-301-C-E Dimensional drawing

Crestron

Crestron DigitalMedia DM-MD64X64 User manual

Crestron

Crestron ZUM-FLOOR-HUB Dimensional drawing

Crestron

Crestron HD-SCALER-HD-E Dimensional drawing

Crestron

Crestron HDI-TX-301-C-2G-E Dimensional drawing

Crestron

Crestron HD-TX-201-C-2G-E Dimensional drawing

Crestron

Crestron DigitalMedia DMC-CATO-HD User manual

Crestron

Crestron CLX-4HSW4 User manual

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual