Crestron UC-SB1 User manual

The Crestron® UC-SB1 UC Video Conference Smart Soundbar is a

front-of-room device that eliminates the need to install additional

microphones or speakers in a conference space. It can be placed on a

credenza beneath the room display(s) or mounted on a wall.

In the Box

1 UC-SB1, UC Video Conference Smart Soundbar

Additional Items

4 Anchor, Drywall, Plastic, 3/8 in. x 1/2 in. (2052565)

1 Cable, USB 3.0, A - B, 6 ft (1.83 m) (2053077)

2 Foot, 2.3 in. x 0.96 in. x 0.15 in., Rubber (2052169)

1 Key, Anchor (4529654)

1 Power Cord, 5 ft 10 in. (1.78 m) (2042043)

1 Power Pack, 24 VDC, 2.5 A, 100-240 VAC (2045873)

4 Screw, 8-AB x 1-1/2 in., Pan Head, Combo (2052567)

1 Template, Overlay (4529513)

UC-SB1 QuickStart

UC Video Conference Smart Soundbar

Install

The soundbar can be placed on a flat surface or mounted on a wall. The soundbar has the following dimensions.

Place on a Flat Surface

If the soundbar is to be placed on a flat surface, attach the included rubber feet to the bottom of the soundbar as shown.

UC-SB1 QuickStart

UC Video Conference Smart Soundbar

Mount on a Wall

The soundbar includes anchors that are suitable for mounting it on sheetrock walls up to 1/2 in. (13 mm) thickness. Masonry and other materials may

require additional installer-supplied mounting hardware.

NOTE: When mounting on a wall beneath a display device, leave 3/4 in. (minimum) clearance above the top of the soundbar. Use the included template

to allow for sufficient clearance between the soundbar and display device.

The following tools are required to mount the soundbar:

lDrywall saw (not included)

lDrill with 5/16 in. bit (not included)

A template is included to provide drill hole locations for the included mounting hardware.

1. Attach the template to the desired mounting location with the template's center reference line at the center of the desired location.

NOTE:Use the center reference hole of the template as a guide to attach the template.

2. Drill two pilot holes on each side of the center reference line as shown in the previous diagram. Each side should have one pilot hole drilled in each row

of the template.

UC-SB1 QuickStart

UC Video Conference Smart Soundbar

3. Use a drywall saw to make a cutout in the wall for the soundbar cables.

NOTE: The cutout in the center of the template provides adequate access for all of the required cabling.

4. Install the four included anchors and screws into the drilled pilot holes.

5. Place the soundbar face down, and pivot the wall bracket away from the soundbar.

UC-SB1 QuickStart

UC Video Conference Smart Soundbar

6. Place the wall bracket over the screws, and hand tighten the screws until the wall bracket is secured to the wall.

7. Route the cables through the cable cutout, and connect the cables as described in Connect.

NOTE: The included power pack's cord is typically routed from the wall opening, through the cable cutout, to the soundbar.

UC-SB1 QuickStart

UC Video Conference Smart Soundbar

Connect

Make the necessary connections as called out in the following diagram. Connect power last.

lPC: Connect the included USB cable to the PC port and to a USB port on the computer. For optimal results, use a USB 3.0 connection.

lCAMERA: Connect a USB camera (sold separately) to the CAMERA port.

l24 V, 2.5 A: Connect the power pack to the 24 V, 2.5 A power input and to an AC power outlet.

lAUDIO IN and AUDIO OUT: The soundbar provides unbalanced, stereo, analog input and output jacks (3.5 mm TRS mini-phone). The AUDIOINport

accommodates an optional line-level audio source which feeds to the internal amplifier and speakers without a volume control or other signal

processing. The AUDIOOUT port provides a line-level signal for an optional assistive listening system and carries the same audio signal as the

soundbar speakers.

UC-SB1 QuickStart

UC Video Conference Smart Soundbar

Complete

Once all connections are made, pivot the soundbar up to the wall bracket

until the soundbar locks into place.

Operation

Status

The front panel status bar illuminates to provide operational information.

lA green status bar indicates the volume level. Raising the volume

increases the status bar's illumination. Lowering the volume decreases

the status bar's illumination. When the volume = “0”, the status bar is

unlit.

lMuting the microphone and speaker turns the two outer segments of

the status bar red.

UC-SB1 QuickStart

UC Video Conference Smart Soundbar

lMuting the microphone turns the center of the status bar red.

System Control

The soundbar can be used in a BYOD scenario where the soundbar is

connected to an end-user’s PC over USB. The soundbar will pass

bidirectional (mic and speaker) audio and camera (if a camera is

connected) across a single USB connection.

Visit the Product Page

Scan the QR code to visit the product page.

UC-SB1

www.crestron.com/model/6511280

UC-SB1 QuickStart

UC Video Conference Smart Soundbar

Additional Information

Regulatory Model:UC-SB

Original Instructions

The U.S. English version of this document is the original instructions.

All other languages are a translation of the original instructions.

Crestron product development software is licensed to Crestron dealers and Crestron

Service Providers (CSPs) under a limited nonexclusive, nontransferable Software

Development Tools License Agreement. Crestron product operating system software is

licensed to Crestron dealers, CSPs, and end-users under a separate End-User License

Agreement. Both of these Agreements can be found on the Crestron website at

www.crestron.com/legal/software_license_agreement.

The product warranty can be found at www.crestron.com/warranty.

The specific patents that cover Crestron products are listed at

www.crestron.com/legal/patents.

Certain Crestron products contain open source software. For specific information, visit

www.crestron.com/opensource.

Crestron and the Crestron logo are either trademarks or registered trademarks of

Crestron Electronics, Inc. in the United States and/or other countries. Other trademarks,

registered trademarks, and trade names may be used in this document to refer to either

the entities claiming the marks and names or their products. Crestron disclaims any

proprietary interest in the marks and names of others. Crestron is not responsible for

errors in typography or photography.

Doc. 8604A

07/30/20

UC-SB1 QuickStart

UC Video Conference Smart Soundbar

Other manuals for UC-SB1

Table of contents

Other Crestron Speakers System manuals

Crestron

Crestron UC-SB1-CAM-FLEX User manual

Crestron

Crestron UC-SB1 User manual

Crestron

Crestron Saros SB-200-P Dimensional drawing

Crestron

Crestron SAROS SB-200-P-B Dimensional drawing

Crestron

Crestron UC-SB1-CAM-L-FLEX User manual

Crestron

Crestron UC-SB1-CAM User manual

Crestron

Crestron UC-SB1 User manual

Crestron

Crestron Surround Sound Tuning Kit User manual

Popular Speakers System manuals by other brands

JVC

JVC CA-MXK5R instructions

LG NB4532B owner's manual

JVC

JVC CA-FSH100 instructions

5Core

5Core Pro Series Operation manual

EAW

EAW MQV1394e Specifications

Lynx

Lynx GXR-LA10A user manual

iLive

iLive ITB066B user guide

RDX

RDX QuickStation 4 product manual

Electro-Voice

Electro-Voice S-122 Specifications

Sven

Sven SPS-619 GOLD Operation manual

Pioneer

Pioneer CS-7070 instruction manual

EAW

EAW UB82e Technical specifications

Sondpex

Sondpex Active Speaker System and Digital Music... User manual and installation instructions

JVC

JVC NX-PN7 instructions

Marshall Amplification

Marshall Amplification AR-DM61-BT user manual

Yamaha

Yamaha NX-A01 - Speaker Sys Product bulletin

SE Audiotechnik

SE Audiotechnik I-LINE manual

Gemini

Gemini WRX-843 Series user manual