Crestron MMK-2000L User manual
Crestron MMK-2000L & WMKM-2000L
Mud Mount Kits
Installation Guide
This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
All brand names, product names and trademarks are the property of their respective owners.
©2002 Crestron Electronics, Inc.
Crestron MMK-2000L & WMKM-2000L Mud Mount Kits
Mud Mount Kits: MMK-2000L &
WMKM-2000L
Description
Mud Mount Kits are the preferred mounting option for the Crestron Isys
TPS-2000L, compact video touchpanel when cutouts made for the touchpanel are too
large. These kits fill in the gaps with additional plastering and provide the support to
hide large irregularities in the touchpanel cutout.
There are two Mud Mount Kits. The MMK-2000L is a pre-construction accessory.
Pre-construction refers to framed walls prior to hanging drywall. This accessory is
designed be used with the Pre-Construction Mount Kit (PMK-2000L) or Back Box
Kit (BB-2000L).
The WMKM-2000L is a post-construction kit. Post-construction refers to framed
walls with drywall hung. This accessory is designed with a mounting plate so that it
can be placed anywhere on a wall without the support from a stud.
NOTE: If necessary, consult the latest revision of the TPS-2000L Operations Guide
(Doc. 5972) for a complete list of mounting options.
Supplied Hardware
The MMK-2000L consists of three items with differing quantities. These items
produce an assembly that attaches to the PMK-2000L or BB-2000L. The
WMKM-2000L consists of the same three items that make up the MMK-2000L as
well as one mounting plate. The mounting plate is the item that provides the
necessary support for post-construction applications.
Supplied Hardware of the MMK-2000L and WMKM-2000L
• ONE (1) Metal Plate, Mounting (only on WMKM-2000L)
• ONE (1) Metal Plate, Mud Ring
• TWO (2) Metal Plate, Fastener
• FOUR (4) Metal, Push-on Fastener
Installation Guide – DOC. 6025 Mud Mount Kits: MMK-2000L & WMKM-2000L •1
Mud Mount Kits Crestron MMK-2000L & WMKM-2000L
Installation
This section provides an installation procedure for each Mud Mount Kit. The
procedure for the MMK-2000L starts below and the “WMKM-2000L Procedure”
starts on page 4.
MMK-2000L Procedure
The procedure in this section provides the necessary steps for the assembly of the
MMK-2000L to either the PMK-2000L or BB-2000L. It is assumed that the
PMK-2000L or BB-2000L has been secured to the stud according to the procedures
in the latest revisions of their respective Installation Guides (Doc. 6018 and Doc.
5973, respectively). Also, it is assumed that drywall is in place and a rectangular
cutout for the touchpanel is made in the drywall (measuring 6 3/8inches wide
(16.159 cm) x 4 ½ inches high (11.389 cm)).
Complete the steps in the order provided. The only tools or materials required and
not supplied are a drywall saw or equivalent, four standard drywall screws, #2
Phillips screwdriver, a level, and tools/material to apply drywall joint compound.
NOTE: The illustrations in this procedure show the installation of the MMK-2000L
with the PMK-2000L. Even though the illustrations only show the PMK-2000L, they
are identical for the BB-2000L as well.
1. Pass a fastener plate through the opening and align its two center holes
with the top two pins on the PMK-2000L. Verify that the pins on the
fastener plate are not between the fastener plate and the PMK-2000L.
Refer to the illustration after this step for visual guidance.
Secure Fastener Plates to PMK-2000L (or BB-2000L)
FASTENER PLATE
QUANTITY 2
PUSH-ON FASTENER
QUANTITY 4
PMK-2000L
2 •Mud Mount Kits: MMK-2000L & WMKM-2000L Installation Guide – DOC. 6025
Crestron MMK-2000L & WMKM-2000L Mud Mount Kits
2. Slid two push-on fasteners over the pins on the PMK-2000L to secure
the fastener plate to the PMK-2000L.
3. Use the second fastener plate and repeat steps 1 and 2 using the lower
two PMK-2000L pins.
NOTE: When installing into the PMK-2000L, verify that the 18 AWG bus wire
securing the cables for the touchpanel remain attached.
4. Verify that the rectangular cutout in the drywall measures 6 3/8inches
wide (16.159 cm) x 4 ½ inches high (11.389 cm).
5. Insert the symmetrical mud ring plate into the opening, as shown in the
illustration after this step.
Insert and Secure Mud Ring Plate into PMK-2000L (or BB-2000L)
STANDARD DRYWALL
SCREW (NOT SUPPLIED)
QUANTITY 4
FLANGES
QUANTITY 4
MUD RING PLATE
QUANTITY 1
6. When the mud ring plate is in position, bend the top two flanges of the
ring upward (approximately 90 degrees) and the bottom two flanges
downward (approximately 90 degrees).
7. Use four standard drywall screws (of adequate length) to secure the
mud ring plate to the rest of the assembly. The screws pass through the
clearance holes in the PMK-2000L (or BB-2000L) and are secured in
the extruded holes of the fastener plates.
8. Verify that the mud ring plate is level.
Installation Guide – DOC. 6025 Mud Mount Kits: MMK-2000L & WMKM-2000L •3
Mud Mount Kits Crestron MMK-2000L & WMKM-2000L
NOTE: Do not over tighten screws. Doing so may over-dimple or rip the mud ring
plate.
9. Use a #2 Phillips screwdriver and tighten the drywall screws by hand
so that they slightly dimple into the holes in the mud ring plate.
10. Apply drywall joint compound as needed to finish the cutout.
11. When dry, the TPS-2000L can be installed using the four tapped holes
in the PMK-2000L. Refer to the latest revision of the TPS-2000L
Operations Guide (Doc. 5972) for details.
WMKM-2000L Procedure
The procedure in this section provides the necessary steps for the assembly and
installation of the WMKM-2000L into a wall. Complete the steps in the order
provided. The only tools or materials required and not supplied are a drywall saw or
equivalent, a level, four standard drywall screws, #2 Phillips screwdriver, and
tools/material to apply drywall joint compound.
1. Insert the two pins on one fastener plate into the top two outer holes on
the mounting plate, as shown in the illustration after this step.
Create the Fastener/Mounting Plate Assembly
FASTENER PLATE
QUANTITY 2
PUSH-ON
FASTENER
QUANTITY 4
MOUNTING
PLATE
QUANTITY 1
2. Slid two push-on fasteners over the pins on the fastener plate to loosely
secure the fastener plate and the mounting plate. Do not push the push-
on fasteners all the way down onto the pins. Slid them on enough to
keep the fastener plate and mounting plate as one fastener/mounting
plate assembly.
3. Use the second fastener plate and repeat steps 1 and 2 on the opposite
side of the mounting plate.
4 •Mud Mount Kits: MMK-2000L & WMKM-2000L Installation Guide – DOC. 6025
Crestron MMK-2000L & WMKM-2000L Mud Mount Kits
4. Locate an area on the wall that is free of miscellaneous wiring and
studs.
5. Make a small hole near the middle of the designated site; verify that the
location is suitable.
NOTE: Make the cutout as level as possible. The mounting plate allows for only
minor leveling adjustments.
6. Use the drywall saw or equivalent to produce a level, rectangular cutout
in the drywall that measures 6 3/8inches wide (16.159 cm) x 4 ½ inches
high (11.389 cm).
7. Insert the symmetrical mud ring plate into the opening, as shown in the
illustration after this step.
Insert the Mud Ring Plate into the Opening
MUD
RING PLATE
QUANTITY 1 OPENING IN
DRYWALL
8. Carefully pass the fastener/mounting plate assembly through the
opening and rest the assembly against the interior surface of the
drywall. Verify that the fastener plates are between the mounting plate
and the drywall. Refer to the illustration after this step for visual
guidance.
Installation Guide – DOC. 6025 Mud Mount Kits: MMK-2000L & WMKM-2000L •5
Mud Mount Kits Crestron MMK-2000L & WMKM-2000L
Fastener Plates Located Between Mounting Plate and Drywall
INSERTED
MUD RING
PLATE
FASTENER/
MOUNTING
PLATE
ASSEMBLY
9. When the fastener/mounting plate assembly is in position, bend the top
two flanges of the mud ring upward (approximately 90 degrees) and the
bottom two flanges downward (approximately 90 degrees). Refer to the
illustration after this step.
NOTE: Fastener/mounting plate assembly will have slight play; this is normal. It
allows for minor adjustments to the TPS-2000L during installation.
Bend Flanges
BEND FLANGES UP
APPROXIMATELY 90°
BEND FLANGES DOWN
APPROXIMATELY 90°
6 •Mud Mount Kits: MMK-2000L & WMKM-2000L Installation Guide – DOC. 6025
Crestron MMK-2000L & WMKM-2000L Mud Mount Kits
10. Use four standard drywall screws (of adequate length) to secure the
plate to the fastener/mounting plate assembly. The screws pass through
the clearance holes in the plate and are secured in the extruded holes of
the fastener plates.
Secure Mud Ring Plate
STANDARD DRYWALL
SCREW (NOT SUPPLIED)
QUANTITY 4
11. Verify that the plate is level before tightening.
NOTE: Do not over tighten screws. Doing so may over-dimple or rip the plate.
12. Use a #2 Phillips screwdriver and tighten the drywall screws by hand
so that they slightly dimple into the holes in the mud ring plate.
13. Run the necessary cables for the touchpanel and secure them behind the
drywall.
14. Apply drywall joint compound as needed to finish the cutout.
15. When dry, the TPS-2000L can be installed using the four tapped holes
in the mounting plate. Refer to the latest revision of the TPS-2000L
Operations Guide (Doc. 5972) for details.
Installation Guide – DOC. 6025 Mud Mount Kits: MMK-2000L & WMKM-2000L •7
Mud Mount Kits Crestron MMK-2000L & WMKM-2000L
Further Inquiries
If you cannot locate specific information or have questions after reviewing this
guide, please take advantage of Crestron's award winning customer service team by
calling the Crestron corporate headquarters at 1-888-CRESTRON [1-888-273-7876].
For assistance in your local time zone, refer to the Crestron website
(www.crestron.com) for a listing of Crestron worldwide offices.
You can also log onto the online help section of the Crestron website to ask
questions about Crestron products. First-time users will need to establish a user
account to fully benefit from all available features.
As of the date of manufacture, the MMK-2000L and WMKM-2000L have been
tested and found to comply with specifications for CE marking.
Future Updates
As Crestron improves functions, adds new features, and extends the capabilities of
the MMK-2000L or WMKM-2000L, additional information may be made available
as manual updates. These updates are solely electronic and serve as intermediary
supplements prior to the release of a complete technical documentation revision.
Check the Crestron website periodically for manual update availability and its
relevance. Updates are identified as an “Addendum” in the Download column.
8 •Mud Mount Kits: MMK-2000L & WMKM-2000L Installation Guide – DOC. 6025
This manual suits for next models
1
Table of contents
Other Crestron Rack & Stand manuals
Crestron
Crestron SMK-6X User manual
Crestron
Crestron TSS-752-MSMK User manual
Crestron
Crestron TSW-750 User manual
Crestron
Crestron SSW-MUMK User manual
Crestron
Crestron PMK-12L User manual
Crestron
Crestron Mud Ring Mount Kit for Cameo 2 MMK-CBF-T User manual
Crestron
Crestron CAEN-MK User manual
Crestron
Crestron CSA-DECOR3-BRKT-163-EC-MTL User manual
Crestron
Crestron HBK-3000 User manual
Crestron
Crestron CNWM-29A User manual
Crestron
Crestron ST-RMK User manual
Crestron
Crestron CPC-WMT How to use
Crestron
Crestron TMK-4000L User manual
Crestron
Crestron TMK-17L User manual
Crestron
Crestron TSW-770-MSMK-ANG User manual
Crestron
Crestron RMK-6L User manual
Crestron
Crestron BB-1000L User manual
Crestron
Crestron RMK-AMP-X User manual
Crestron
Crestron UCA-RMK-1U User manual
Crestron
Crestron RMK-6000 User manual
Popular Rack & Stand manuals by other brands
Salamander
Salamander Acadia AC/W/L400/WH Assembly instructions
Fohhn
Fohhn VAT-09 Mounting instruction
ricoo
ricoo FS0522 quick start guide
AMSOIL
AMSOIL BMK-22 Installation and service instructions
Kargo Master
Kargo Master 48220 installation guide
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 installation instructions
