Cree NTA Series User manual

NTA Series

LED Area Light

Trunnion, Adjustable Arm and Direct Arm Mount

1 of 8 LPN00631X0001A0_B

INSTALLATION INSTRUCTIONS

INSTRUCTIONS D’INSTALLATION

TO INSTALL:

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed including the following:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

1. DANGER- Risk of shock- Disconnect power before installation.

DANGER – Risque de choc – Couper l’alimentation avant l’installation.

2. This luminaire must be installed in accordance with the NEC or your local electrical code. If you are not familiar with these codes

and requirements, consult a qualied electrician.

Ce produit doit être installé conformément à NEC ou votre code électrique local. Si vous n’êtes pas familier avec ces codes et ces

exigences, veuillez contacter un électricien qualié.

3. Suitable for wet locations.

Convient aux emplacements mouilles

4. Suitable for operation in ambient not exceeding 40°C.

Peut etre utilise a une temperature ambiante n’excedant pas 40°C.

5. Suitable for mounting within 1.2M (4ft) of the ground.

Peut etre installe a moins de 1,2 m (4 pi) du sol.\

6. Min. 75°C supply conductors.

Les ls d’alimentation 75°c min.

7. Class 1 wiring only.

Cablage de classe 1 uniquement.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

TRUNNION MOUNT- REQUIRES USE OF NTX-TR ACCESSORY

NOTE: Area lights are only designed for

mounting orientation from 0° (horizontal) to

45° tilt.

NOTE: Area lights are not to be used as

uplights.

STEP 1:

Plug the female end of the quick connect,

supplied with the trunnion, into the male

connector on the luminaire. Make sure the two

halves lock together. See Figure 1.

STEP 2:

Align the four holes in the inner trunnion with

the four tapped holes in the luminaire housing.

Attach the trunnion to the luminaire using

the (4) 5/16" (8 mm) bolts and lockwashers

supplied with the trunnion kit. Tighten bolts to

132 in-lbs (15 N·m). See Figure 2.

STEP 3:

Mount the luminaire in the desired location

using (2) 3/8" (10 mm) bolts (customer

supplied) appropriate for the mounting surface.

See Figure 3.

STEP 4:

Make wiring connections to the cord leads per

the Electrical Connections section.

STEP 5:

Remove #10-24 positioning screws on both

sides of the trunnion.

STEP 6:

Loosen 5/16" (8 mm) hex head bolts located on

both sides of the trunnion.

STEP 7:

Rotate trunnion to desired tilt angle. Line up

inner and outer trunnion positioning holes.

STEP 8:

Insert one #10-24 screw, removed in Step

5, into matching holes of inner and outer

trunnions. Tighten screw to 30 in-lbs (35 N·m).

Repeat with screw on opposite side of trunnion.

STEP 9:

Tighten both 5/16" hex head bolts on opposite

sides of the trunnion to 132 in-lbs (15 N·m).

2 3

Female End of

Connector

Male End of

Connector

Inner

Trunnion

#10-24 Screws

to Adjust the

Orientation

For Wall

Mounting,

Keep the

Keyholes Facing

Upwards During

Installation

Outer Trunnion.

Fix this on the

Mounting Surface

(4) 5/16” (8 mm)

Bolts

Bolts into Keyholes Slots First

(2) 5/16"

(8 mm)

Bolts

2 of 8 LPN00631X0001A0_B

TRUNNION WITH BUTTON PHOTOCELL-

REQUIRES USE OF NTX-TR-PK

ACCESSORY AND BUTTON PHOTOCELL

NOTE: Area lights are only designed for

mounting orientation from 0° (horizontal) to

45° tilt.

NOTE: Area lights are not to be used as

uplights.

STEP 1:

Plug the female end of the quick connect,

supplied with the trunnion, into the male

connector on the luminaire. Make sure the two

halves lock together. See Figure 1.

STEP 2:

Align the four holes in the front half of the

trunnion with the four tapped holes in the

luminaire housing. Attach the trunnion to the

luminaire using the (4) 5/16” (8 mm) bolts and

lockwashers supplied with the trunnion kit.

Tighten bolts to 132 in-lbs (15 N·m). See

Figure 4.

STEP 3:

Remove wiring compartment cover on trunnion

by loosening (2) screws. See Figure 4.

STEP 4:

Remove the center knockout from the cover by

striking knockout with a hammer and punch.

STEP 5:

Remove the nut from the threaded nipple of

the photocell and insert the threaded nipple

of the photocell through the hole in the cover.

The body of the photocell and the o-ring on the

threaded nipple should remain on the inside

surface of the cover.

STEP 6:

Tighten the nut onto the exposed end of the

threaded nipple to secure the photocell to the

cover.

STEP 7:

Wire the photocell by following the wiring

instructions included with the photocell.

STEP 8:

Reattach the wiring compartment cover that

was removed in Step 3. Tighten the screws to

30 in-lbs (3.5 N·m).

NOTE: Make sure no wires are pinched.

STEP 9:

Mount the luminaire in the desired location

using (2) 3/8” (10 mm) bolts (customer

supplied) appropriate for the mounting surface.

See Figure 3.

STEP 10:

Make wiring connections to the cord leads per

the Electrical Connections section.

STEP 11:

Remove #10-24 positioning screws on both

sides of the trunnion.

STEP 12:

Loosen 5/16" (8 mm) hex head bolts located on

both sides of the trunnion.

STEP 13:

Rotate trunnion to desired tilt angle. Line up

inner and outer trunnion positioning holes.

STEP 14:

Insert one #10-24 screw, removed in Step

11, into matching holes of inner and outer

trunnions. Tighten screw to 30 in-lbs (35 N·m).

Repeat with screw on opposite side of trunnion.

STEP 15:

Tighten both 5/16” hex head bolts on opposite

sides of the trunnion to 132 in-lbs (15 N·m).

TRUNNION WITH TWIST-LOCK

PHOTOCELL- REQUIRES USE OF NTX-

TR-3R ACCESSORY AND TWIST-LOCK

PHOTOCELL

NOTE: Area lights are only designed for

mounting orientation from 0° (horizontal) to

45° tilt.

NOTE: Area lights are not to be used as

uplights.

STEP 1:

Plug the female end of the quick connect,

supplied with the trunnion, into the male

connector on the luminaire. Make sure the two

halves lock together. See Figure 1.

STEP 2:

Position luminaire to be assembled to trunnion

optic side down with mounting holes facing

towards you.

IMPORTANT: Trunnion with Twist Lock

Photocell must be oriented with twist lock

receptacle on the right side of the trunnion as

viewed from behind luminaire.

STEP 3:

Align the four holes in the inner trunnion with

the four tapped holes in the luminaire housing.

Attach the trunnion to the luminaire using

the (4) 5/16” (8 mm) bolts and lockwashers

supplied with the trunnion kit. Tighten bolts to

132 in-lbs (15 N·m). See Figure 5.

STEP 4:

Mount the luminaire in the desired location

using (2) 3/8” (10 mm) bolts (customer

supplied) appropriate for the mounting surface.

See Figure 3.

STEP 5:

Make wiring connections to the cord leads per

the Electrical Connections section.

STEP 6:

Remove #10-24 positioning screws on both

sides of the trunnion.

STEP 7:

Loosen 5/16" (8 mm) hex head bolts located on

both sides of the trunnion.

STEP 8:

Rotate trunnion to desired tilt angle. Line up

inner and outer trunnion positioning holes.

STEP 9:

Insert #10-24 screw, removed in Step 6, into

matching holes of inner and outer trunnion.

Tighten screw to 30 in-lbs (35 N·m). Repeat

with screw on opposite side of trunnion.

STEP 10:

Tighten both 5/16” hex head bolts on opposite

sides of the trunnion to 132 in-lbs (15 N·m).

STEP 11:

Twist lock receptacle must be positioned

to orient photocell between +/- 45° from

vertical. See Figure 6. If the receptacle needs

to be repositioned to orient photocell in this

tilt range, remove the screws holding the

receptacle mounting bracket to the trunnion

(See Figure 5), and reposition mounting

bracket to properly orient receptacle. Retighten

screws to 30 in-lbs (3.5 N·m) after repositioning

bracket.

STEP 12:

Install twist lock photocell.

Wiring

Compartment

Cover

(2) Screws

Button Photocell

Mounting Bracket

of the Trunnion

Front Half of Mounting

Arm. Fix this to the

Luminaire Head

For Wall Mounting,

Keep the Keyholes

Facing Upwards During

Installation

Mounting Arm Fix this

to the Luminaire Head

using (4) Bolts

Rear Trunnion

Bracket. Fix this

to the Mounting

Surface

(2) Adjustment

Screws for Twist

Lock Receptacle

(One Each Side of

Twist Lock)

Twist Lock

Photocell

Receptacle

For Wall Mounting,

Keep the Keyholes

Facing Upwards During

Installation

#10-24 Screws

to Adjust the

Orientation

(2) 5/16"

(8 mm)

Bolts

#10-24 Screws

to Adjust the

Orientation

(2) 5/16"

(8 mm)

Bolts

3 of 8 LPN00631X0001A0_B

ADJUSTABLE ARM MOUNT- REQUIRES USE OF NTX-AA ACCESSORY

NOTE: Area lights are only designed for

mounting orientation from 0° (horizontal) to

45° tilt.

NOTE: Area lights are not to be used as

uplights.

STEP 1:

Plug the female end of the quick connect,

supplied with the trunnion, into the male

connector on the luminaire. Make sure the two

halves lock together. See Figure 1.

STEP 2:

Align the four holes in the upper adjustable

arm with the four tapped holes in the luminaire

housing. Attach the adjustable arm to the

luminaire using the (4) 5/16” (8 mm) bolts and

lockwashers supplied with the adjustable arm

kit. Tighten bolts to 132 in-lbs (15 N·m). See

Figure 7.

STEP 3:

Remove wiring compartment cover on

adjustable arm by loosening (2) screws. See

Figure 7.

STEP 4:

Feed supply leads up through the tenon that

the luminaire will be mounted on.

STEP 5:

Route supply leads through open end of the

adjustable arm and into wiring compartment.

NOTE: It may be necessary to disassemble

the upper and lower portions of the adjustable

arm in order to run the leads into the wiring

compartment. If disassembly is necessary,

remove the 3/8" (10 mm) bolt and lockwasher

inside the wiring compartment and route leads

into wiring compartment. See

Figure 7. Reassemble upper and lower arm

halves and replace 3/8" bolt and lockwasher.

Do not tighten bolt at this time.

STEP 6:

Strain relief is required for electrical

connections on slip fitter mounts at heights of

25' (7.6 m) and above. Tie a knot in the supply

leads above the hole where the leads enter

the wiring chamber to reduce the strain on

the connections. Make sure knot will not slip

through opening in wiring compartment.

STEP 7:

Slip lower adjustable arm over 2 -3/8" (60 mm)

O.D. heavy wall pipe or tenon making sure not

to pinch any leads. Aim the luminaire in the

proper direction and hand tighten all four Allen

head set screws against outer wall of tenon.

Hand tighten (4) screws against tenon. Once all

four screws are hand tightened, secure them

by tightening to 140 in-lbs (16 N·m).

STEP 8:

If 3/8" bolt holding the two halves of the

adjustable arm together was not loosened in

Step 5, loosen the bolt (DO NOT remove it) at

this time.

STEP 9:

Tilt the luminaire to the desired angle and

tighten the 3/8" (10 mm) bolt to 19 ft-lbs (25

N·m) to lock the adjustable arm in place.

STEP 10:

Make the wiring connections inside the wiring

compartment per the Electrical Connections

section.

STEP 11:

Replace the wiring compartment cover that

was removed in Step 3. Tighten screws to 30

in-lbs (3.5 N·m).

ADJUSTABLE ARM MOUNT WITH

BUTTON PHOTOCELL- REQUIRES USE

OF NTX-AA ACCESSORY AND BUTTON

PHOTOCELL

NOTE: Area lights are only designed for

mounting orientation from 0° (horizontal) to

45° tilt.

NOTE: Area lights are not to be used as

uplights.

STEP 1:

Plug the female end of the quick connect,

supplied with the trunnion, into the male

connector on the luminaire. Make sure the two

halves lock together. See Figure 1.

STEP 2:

Align the four holes in the upper adjustable

arm with the four tapped holes in the luminaire

housing. Attach the adjustable arm to the

luminaire using the (4) 5/16” (8 mm) bolts and

lockwashers supplied with the adjustable arm

kit. Tighten bolts to 132 in-lbs (15 N·m). See

Figure 7.

STEP 3:

Remove wiring compartment cover on adjustab

le arm by removing (2) screws. See Figure 7.

STEP 4:

Feed supply leads up through the tenon that

the luminaire will be mounted on.

STEP 5:

Route supply leads through open end of the

adjustable arm and into wiring compartment.

NOTE: It may be necessary to disassemble

the upper and lower portions of the adjustable

arm in order to run the leads into the wiring

compartment. If disassembly is necessary,

remove the 3/8” (10 mm) bolt and lockwasher

inside the wiring compartment and route leads

into wiring compartment. See

Figure 7. Reassemble upper and lower arm

halves and replace 3/8” bolt and lockwasher.

Do not tighten bolt at this time.

Allowable

Photocell Tilt

Angle Rang

-45°

From

Vertical

45°

From

Vertical

Wiring

Compartment

Cover Plate

(2) Screws

Remove the Bolt at

the Center Inside

the Cover Plate to

Separate the Two

Halves

Tighten the Screws

Here to Fix the

Adjustable Arm on

the Pole

Lower Half of the

Arm to be Fixed on

the Mounting Pole

Upper Arm to be

Fixed on to the

Luminaire Head

using (4) bolts

Supply Leads

Button Photocell

4 of 8 LPN00631X0001A0_B

STEP 11:

Remove the nut from the threaded nipple of

the photocell and insert the threaded nipple

of the photocell through the hole in the cover.

The body of the photocell and the o-ring on

the threaded nipple should remain on the

inside surface of the cover.

STEP 12:

Tighten the nut onto the exposed end of the

threaded nipple to secure the photocell to the

cover.

STEP 13:

Wire the photocell by following the wiring

instructions included with the photocell.

STEP 14:

Connect supply ground lead to luminaire

ground lead.

STEP 15:

Replace the wiring compartment cover that

was removed in Step 3. Tighten screws to 30

in-lbs (3.5 N·m).

ADJUSTABLE ARM MOUNT WITH TWIST-LOCK PHOTOCELL- REQUIRES USE OF

NTX-AA-3R ACCESSORY AND TWIST-LOCK PHOTOCELL

NOTE: Area lights are only designed for

mounting orientation from 0° (horizontal) to

45° tilt.

NOTE: Area lights are not to be used as

uplights.

STEP 1:

Plug the female end of the quick connect,

supplied with the trunnion, into the male

connector on the luminaire. Make sure the two

halves lock together. See Figure 1.

STEP 2:

Position luminaire to be assembled to

adjustable arm face down with mounting holes

facing towards you.

IMPORTANT: Adjustable arm with Twist Lock

Photocell must be mounted with twist lock

receptacle on the right side of the adjustable

arm as viewed from behind luminaire.

STEP 3:

Align the four holes in the upper adjustable

arm with the four tapped holes in the

luminaire housing. Attach the adjustable

arm to the luminaire using the (4) 5/16” (8

mm) bolts and lockwashers supplied with the

adjustable arm kit. Tighten bolts to 132 in-lbs

(15 N·m). See Figure 8.

STEP 4:

Remove wiring compartment cover on

adjustable arm by removing (2) screws. See

Figure 8.

STEP 5:

Feed supply leads up through the tenon that

the luminaire will be mounted on.

STEP 6:

Route supply leads through open end of the

adjustable arm and into wiring compartment.

NOTE: It may be necessary to disassemble

the upper and lower portions of the adjustable

arm in order to run the leads into the wiring

compartment. If disassembly is necessary,

remove the 3/8” (10 mm) bolt and lockwasher

inside the wiring compartment and route

leads into wiring compartment. See

Figure 8. Reassemble upper and lower arm

halves and replace 3/8” bolt and lockwasher.

Do not tighten bolt at this time.

STEP 7:

Strain relief is required for electrical

connections on slip fitter mounts at heights of

25’ (7.6 m) and above. Tie a knot in the supply

leads above the hole where the leads enter

the wiring chamber to reduce the strain on

the connections. Make sure knot will not slip

through opening in wiring compartment.

STEP 8:

Slip lower adjustable arm over 2 -3/8” (60

mm) O.D. heavy wall pipe or tenon making

sure not to pinch any leads. Aim the luminaire

in the proper direction and hand tighten all

four Allen head set screws against outer

wall of tenon. Once all four screws are hand

tightened, secure them by tightening them to

140 in-lbs (16 N·m).

STEP 9:

If 3/8” bolt holding the two halves of the

adjustable arm together was not loosened in

Step 6, loosen the bolt (DO NOT remove it) at

this time.

STEP 6:

Strain relief is required for electrical connections on slip

fitter mounts at heights of 25’ (7.6 m) and above. Tie a knot

in the supply leads above the hole where the leads enter

the wiring chamber to reduce the strain on the connections.

Make sure knot will not slip through opening in wiring

compartment.

STEP 7:

Slip lower adjustable arm over 2 -/” (60 mm) O.D. heavy

wall pipe or tenon making sure not to pinch any leads. Aim

the luminaire in the proper direction and hand tighten all four

Allen head set screws against outer wall of tenon. Once all

four screws are hand tightened, secure them by tightening

them to 140 in-lbs (16 N·m).

STEP 8:

If 3/8” bolt holding the two halves of the adjustable arm

together was not loosened in Step 5, loosen the bolt (DO NOT

remove it) at this time.

STEP 9:

Tilt the luminaire to the desired angle and tighten the 3/8”

(10 mm) bolt to 19 ft-lbs (25 N·m) to lock the adjustable arm

in place.

STEP 10:

Remove the center knockout form the wiring compartment

cover by striking knockout with a punch and hammer.

Remove the Bolt at

the Center Inside

the Cover Plate to

Separate the Two

Halves

(2) Screws for

Removal of Wiring

Compartment

Cover

Tighten the Screws

Here to Fix the

Adjustable Arm on

the Pole

Lower Half of the

Arm to be Fixed on

the Mounting Pole

Upper Arm to be

Fixed on to the

Luminaire Head

using (4) bolts

Twist Lock

Photocell

Receptacle

Supply Leads

5 of 8 LPN00631X0001A0_B

STEP 10:

Tilt the luminaire to the desired angle and

tighten the 3/8” (10 mm) bolt to 19 ft-lbs

(25 N·m) to lock the adjustable arm in place.

STEP 11:

Make the wiring connections inside the wiring

compartment per the Electrical Connections

section.

STEP 12:

Replace the wiring compartment cover that

was removed in Step 4. Tighten screws to

30 in-lbs (3.5 N·m).

NOTE: Twist lock receptacle must be

positioned to orient photocell between

+/- 45° from vertical. See Figure 6. Make

sure photocell will be properly oriented when

replacing cover.

STEP 13:

Install twist lock photocell.

DIRECT ARM MOUNT- REQUIRES USE OF NTA-DA ACCESSORY

NOTE: Area lights are not to be used as

uplights.

STEP 1:

Remove the (2) 1/4-20 screws from the top of

the direct arm and the 1/4-20 screw on the

bottom of the direct arm. See Figure 9.

STEP 2:

Remove hinged door from bottom of direct

arm.

STEP 3:

Separate top and bottom halves of the direct

arm.

STEP 4:

Plug the female end of the quick connect,

supplied with the direct arm, into the male

connector on the luminaire. Make sure the two

halves lock together. See Figure 1.

STEP 5:

Pass the free end of the power cord through

the large hole in the top half of the direct arm.

STEP 6:

Align the four holes in the top half of the arm

with the four tapped holes in the luminaire

housing. Attach the top half of the arm to the

luminaire using the (4) 5/16” (8 mm) x 1" (25

mm) bolts and lock washers supplied with the

arm kit. Tighten bolts to 132 in-lbs (15 N·m).

See Figure 9.

STEP 7:

Use template in Figure 11 on page 6 for pole

drilling if pole is not pre-drilled.

NOTE: Template is not to scale.

STEP 8:

Mount bottom half of direct arm to pole by

threading 5/16" (8 mm) x 3" (76 mm) bolt with

lock washer through top hole in arm, through

top hole in pole, and into top threaded hole of

backing plate inside pole.

Thread 5/16" (8 mm) x 2" (51 mm) bolt with

lock washers through lower slot in arm, lower

hole in pole, and into bottom threaded hole

of backing plate. See Figure 10. Tighten both

bolts to 132 in-lbs (15 N·m).

NOTE: A round pole adapter is included with

the direct arm accessory kit. The adapter will

work with round poles from 4" (102 mm) to

5" (127 mm) in diameter. To utilize adapter,

sandwich adapter between bottom half of arm

and pole (radius side of adapter towards pole)

when attaching arm to pole. See Figure 10.

STEP 9:

Pass the free end of the cord from the top

half of the arm through the center hole in the

bottom half of the arm and into the pole. See

Figure 10.

NOTE: When routing cord to the hole in the

bottom half of the arm, make sure cord

passes above the horizontal crossbar on

bottom half or arm.

STEP 10:

Place the top half of the arm that is attached

to the luminaire head onto the bottom half of

the arm.

STEP 11:

Replace the (2) 1/4-20 screws that were

removed from the top half of the arm. Tighten

the screws to 72 in-lbs (8 N·m).

STEP 12:

Replace the arm cover and retention screw.

Tighten the screw to 72 in-lbs (8 N·m).

STEP 13:

Make wiring connections to the cord leads

inside the pole per the Electrical Connections

section.

STEP 14:

Replace the pole cap.

Square pole mount

Round pole mount

Remove (2)

1/4-20 Screws to

Disassemble Arm

(4) Bolts to Attach

Arm to Housing

Top Half of Arm

Bottom Half of Arm

Remove the Hinged

Door by Loosening

this 1/4-20 Screw

Round Pole Adapter

5/16" x 3" Bolt

5/16" x 2" Bolt

5/16" x 3" Bolt

6 of 8 LPN00631X0001A0_B

2.000"

(51 mm)

1.000"

(25.4 mm)

ø0.344" (9 mm) hole

2 Required

ø0.500" (13 mm) hole

NOT TO SCALE

2.000"

(51 mm)

7 of 8 LPN00631X0001A0_B

DIRECT ARM MOUNT WITH EXTENSION ARM AND TWIST-LOCK PHOTOCELL- REQUIRES USE OF NTA-DA, NTX-3R ACCESSORIES

AND TWIST-LOCK PHOTOCELL

NOTE: Area lights are not to be used as uplights.

STEP 1:

Plug the female end of the quick connect, supplied with the trunnion,

into the male connector on the luminaire. Make sure the two halves lock

together. See Figure 1.

STEP 2:

Align the four non-threaded holes in the extension arm with the four

tapped holes in the luminaire housing. Attach the extension arm to the

luminaire using the (4) 5/16 (8 mm) bolts and lock washers supplied

with the extension arm kit. Tighten bolts to 132 in-lbs (15 N·m). See

Figure 12.

NOTE: Twist- lock receptacle must be facing up (away from illuminated

face of luminaire) to prevent leakage and unwanted cycling.

STEP 3:

Remove the (2) 1/4-20 screws from the top of the direct arm and the 1/4-

20 screw on the bottom of the direct arm. See Figure 9.

STEP 4:

Remove hinged door from bottom of direct arm.

STEP 5:

Separate top and bottom halves of the direct arm.

STEP 6:

Plug the female end of the quick connect, supplied with the direct arm,

into the male connector on the extension arm. Make sure the two halves

lock together. See Figure 1.

STEP 7:

Pass the free end of the power cord through the large hole in the top

half of the direct arm.

STEP 8:

Align the four holes in the top half of the arm with the four tapped holes

in the extension arm. Attach the top half of the arm to the extension arm

using the (4) 5/16” (8 mm) x 1” (25 mm) bolts and lock washers supplied

with the direct arm kit. Tighten bolts to 132 in-lbs (15 N·m). See

Figure 12.

STEP 9:

Use template in Figure 11 on page 6 for pole drilling if pole is not pre-

drilled.

NOTE: Template is not to scale.

STEP 10:

Mount bottom half of direct arm to pole by threading 5/16” (8 mm) x 3”

(76 mm) bolt with lock washer through top hole in arm, through top hole

in pole, and into top threaded hole of backing plate inside pole. Thread

5/16” (8 mm) x 2” (51 mm) bolt with lock washers through lower slot in

arm, lower hole in pole, and into bottom threaded hole of backing plate.

See Figure 10. Tighten both bolts to 132 in-lbs (15 N·m).

NOTE: A round pole adapter is included with the direct arm accessory

kit. The adapter will work with round poles from 4” (102 mm) to 5”

(127 mm) in diameter. To utilize adapter, sandwich adapter between

bottom half of arm and pole (radius side of adapter towards pole) when

attaching arm to pole. See Figure 10.

STEP 11:

Pass the free end of the cord from the top half of the arm through the

center hole in the bottom half of the arm and into the pole. See Figure

10.

NOTE: When routing cord to the hole in the bottom half of the arm, make

sure cord passes above the horizontal crossbar on bottom half or arm.

STEP 12:

Place the top half of the direct arm that is attached to the extension arm

and luminaire head onto the bottom half of the direct arm.

STEP 13:

Replace the (2) 1/4-20 screws that were removed from the top half of the

arm. Tighten the screws to 72 in-lbs (8 N·m).

STEP 14:

Replace the arm cover and retention screw. Tighten the screw to

72 in-lbs (8 N·m).

STEP 15:

Make wiring connections to the cord leads inside the pole per the

Electrical Connections section.

STEP 16:

Install twist-lock photocell.

STEP 17:

Replace the pole cap.

Square pole mount

12 Remove (2)

1/4-20 Screws to

Disassemble Arm

Photocell

Receptacle

Fix the Extension Arm to

the Luminaire Head using

(4) Bolts

Remove the Hinged

Door by Loosening

this 1/4-20 Screw

Top Half of Arm

Bottom Half

of Arm

8 of 8 LPN00631X0001A0_B

See http://lighting.cree.com/warranty for warranty and specifications. Cree®and the Cree Logo are registered trademarks of

Cree, Inc.

lighting.cree.com

FCC

CAUTION: Changes or modifications not expressly approved could void your authority to use this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will

be required to correct the interference at his own expense.

CAN ICES-005 (A)/NMB-005 (A)

ELECTRICAL CONNECTIONS

STEP 1:

Make the following Electrical Connections to supply cord:

a. For 120/277/347V connect the black fixture lead to the

voltage supply or Hot 1 (for 208/240/480V wiring).

b. For 120/277/347V connect the white fixture lead to the

neutral supply or Hot 2 (for 208/240/480V wiring).

c. Connect the luminaire ground (green or green/yellow)

lead to the supply ground lead.

d. If Dimming is an option; connect the violet dimming

positive lead to the supply dimming positive lead. Cap off

violet lead if dimming is not used.

e. If Dimming is an option; connect the grey dimming

negative lead to the supply dimming negative lead. Cap off

grey lead if dimming is not used.

f. NOTE: For dimming connections, use Class 1 wiring

methods only.

LINE

OR HOT 1

GREEN

LINE-BLACK

GROUND-GREEN

NEUTRAL-WHITE

DIM (-) GREY

DIM (+) VIOLET

NEUTRAL

OR HOT 2

VIOLET

GREY

SUPPLY WIRING

(DIMMING OPTIONAL)

LUMINAIRE

Série NTA

Projecteur d'illumination à DEL

Montage du tourillon, du bras réglable et du bras direct

1 sur 8 LPN00631X0001A0_B

INSTRUCTIONS D’INSTALLATION

INSTALLATION INSTRUCTIONS

POUR INSTALLER:

MESURES DE SÉCURITÉ IMPORTANTES

Lorsque vous utilisez un équipement électrique, vous devez toujours respecter les règles de sécurité élémentaires, notamment les suivantes :

LISEZ ET SUIVEZ TOUTES LES CONSIGNES DE SÉCURITÉ

1. DANGER – Risque de choc – Couper l’alimentation avant l’installation.

DANGER – Risk of shock- Disconnect power before installation.

2. Ce produit doit être installé conformément à NEC ou votre code électrique local. Si vous n’êtes pas familier avec ces codes et ces

exigences, veuillez contacter un électricien qualiﬁ é.

This luminaire must be installed in accordance with the NEC or your local electrical code. If you are not familiar with these codes

and requirements, consult a qualiﬁ ed electrician.

3. Convient aux emplacements mouillés.

Suitable for wet locations.

4. Peut être utilisé à une température ambiante n’excédant pas 40 °C.

Suitable for operation in ambient not exceeding 40°C.

5. Peut être installé à moins de 1,2 m (4 pi) du sol.

Suitable for mounting within 1.2M (4ft) of the ground.

6. Les ﬁ ls d’alimentation 75 °C min.

Min. 75°C supply conductors.

7. Câblage de classe 1 uniquement.

Class 1 wiring only.

VEUILLEZ GARDER CES INSTRUCTIONS POUR RÉFÉRENCE ULTÉRIEURE

MONTAGE DU TOURILLON – NÉCESSITE L’ACCESSOIRE NTX-TR

REMARQUE: Les projecteurs d’illumination sont

uniquement conçus pour un angle de montage de

0° (horizontal) à une inclinaison de 45°.

REMARQUE: Les projecteurs d’illumination ne

doivent pas être utilisés comme luminaire à

éclairage dirigé vers le haut.

ÉTAPE 1:

Branchez l'extrémité femelle du raccord rapide,

fourni avec le tourillon, dans le connecteur mâle

du luminaire. Assurez-vous que les deux moitiés

se verrouillent ensemble. Voir Figure1.

ÉTAPE 2:

Alignez les quatre trous du tourillon interne

avec les quatre trous taraudés du boîtier du

luminaire. Fixez le tourillon au luminaire à

l'aide des quatre (4) boulons de 8mm (5/16po)

et des rondelles de blocage fournis avec

l'ensemble du tourillon. Serrez les boulons à

15Nm (132po-lb). Voir Figure2.

ÉTAPE 3:

Montez le luminaire à l'endroit désiré à l'aide de

(2) boulons de 10mm (3/8po) (fournis par le client)

adaptés à la surface de montage. Voir Figure 3.

ÉTAPE 4:

Effectuez les branchements de câblage aux

fils du cordon conformément à la section

Branchements électriques.

ÉTAPE 5:

Retirez les vis de réglage n°10-24 des deux

côtés du tourillon.

ÉTAPE 6:

Desserrez les boulons à tête hexagonale de 8mm

(5/16po) situés des deux côtés du tourillon.

ÉTAPE 7 :

Pivotez le tourillon à l'angle d'inclinaison

désiré. Alignez les trous de réglage du tourillon

interne et externe.

ÉTAPE 8 :

Insérez une vis n° 10-24, retirée à l'étape 5, dans

les trous correspondants du tourillon interne et

externe. Serrez la vis à 35Nm (30po-lb). Répétez

l'opération avec la vis sur le côté opposé de

l'articulation.

ÉTAPE 9 :

Serrez les 2 boulons à tête hexagonale de 8mm

(5/16po) des deux côtés opposés du tourillon à

15Nm (132po-lb).

2 3

Extrémité femelle

du connecteur

Extrémité mâle

du connecteur

Tourillon

interne

Vis 10-24 pour

régler l'orientation

Pour montage

mural, Gardez les

trous de serrure

orientés vers le

haut pendant

l'installation.

Tourillon externe

Fixez ceci sur la

surface de montage

(4) boulons de

8mm (5/16po)

Boulons dans fentes des trous de serrure d’abord

(2) boulons

de 13mm

(5/10po)

2 sur 8 LPN00631X0001A0_B

TOURILLON AVEC PHOTOCELLULE À

BOUTON - NÉCESSITE L’ACCESSOIRE

NTX-TR-PK

REMARQUE: Les projecteurs d’illumination sont

uniquement conçus pour un angle de montage

de 0° (horizontal) à une inclinaison de 45°.

REMARQUE: Les projecteurs d’illumination

ne doivent pas être utilisés comme luminaire à

éclairage dirigé vers le haut.

ÉTAPE 1:

Branchez l'extrémité femelle du raccord rapide,

fourni avec le tourillon, dans le connecteur mâle

du luminaire. Assurez-vous que les deux moitiés

se verrouillent ensemble. Voir Figure1.

ÉTAPE 2:

Alignez les quatre trous du tourillon avec les

quatre trous taraudés du boîtier du luminaire.

Fixez le tourillon au luminaire à l'aide des quatre

(4) boulons de 8mm (5/16po) et des rondelles

de blocage fournis avec l'ensemble du tourillon.

Serrez les boulons à 15Nm (132po-lb). Voir

Figure4.

ÉTAPE 3:

Retirez le couvercle du compartiment des fils

sur le tourillon en desserrant les (2) vis. Voir

Figure 4.

ÉTAPE 4:

Retirez la débouchure centrale du couvercle en

la frappant à l'aide d'un marteau et d'un poinçon.

ÉTAPE 5:

Retirez l’écrou du raccord fileté de la cellule

photoélectrique et insérez le raccord fileté de

la photocellule à travers le trou du couvercle.

Le corps de la photocellule et le joint torique du

raccord fileté doivent restés sur la paroi interne

du couvercle.

ÉTAPE 6:

Serrez l'écrou sur l'extrémité exposée du

raccord fileté pour fixer la photocellule au

couvercle.

ÉTAPE 7 :

Branchez la photocellule en suivant les instructions

de branchement fournies avec la photocellule.

ÉTAPE 8 :

Replacez le couvercle du compartiment des fils

retiré à l'étape 3. Serrez les vis à 3,5Nm (30po-lb).

REMARQUE: Assurez-vous que les fils ne sont

pas pincés.

ÉTAPE 9 :

Montez le luminaire à l'endroit désiré à l'aide

de (2) boulons de 10mm (3/8po) (fournis par

le client) adaptés à la surface de montage. Voir

Figure 3.

ÉTAPE 10:

Effectuez les branchements de câblage aux

fils du cordon conformément à la section

Branchements électriques.

ÉTAPE 11:

Retirez les vis de réglage n°10-24 des deux

côtés du tourillon.

ÉTAPE 12:

Desserrez les boulons à tête hexagonale

de 8mm (5/16po) situés des deux côtés du

tourillon.

Étape 13.

Pivotez le tourillon à l'angle d'inclinaison désiré.

Alignez les trous de réglage du tourillon interne

et externe.

ÉTAPE 14:

Insérez une vis n° 10-24, retirée à l'étape 11, dans

les trous correspondants du tourillon interne et

externe. Serrez la vis à 35Nm (30po-lb). Répétez

l'opération avec la vis sur le côté opposé de

l'articulation.

ÉTAPE 15:

Serrez les 2 boulons à tête hexagonale de 8mm

(5/16po) des deux côtés opposés du tourillon à

15Nm (132po-lb).

TOURILLON AVEC PHOTOCELLULE

À VERROU TOURNANT - NÉCESSITE

L’ACCESSOIRE NTX-TR-3R ET UNE

PHOTOCELLULE À VERROU TOURNANT

REMARQUE: Les projecteurs d’illumination sont

uniquement conçus pour un angle de montage

de 0° (horizontal) à une inclinaison de 45°.

REMARQUE: Les projecteurs d’illumination ne

doivent pas être utilisés comme luminaire à

éclairage dirigé vers le haut.

ÉTAPE 1:

Branchez l'extrémité femelle du raccord rapide,

fourni avec le tourillon, dans le connecteur

mâle du luminaire. Assurez-vous que les deux

moitiés se verrouillent ensemble. Voir Figure1.

ÉTAPE 2:

Positionnez le luminaire à assembler au

tourillon avec le côté optique vers le bas et les

trous de montage orientés vers vous.

IMPORTANT: Le tourillon avec la photocellule

à verrou tournant doit être orienté avec le

réceptacle du verrou tournant sur le côté droit

du tourillon, vu de derrière le luminaire.

ÉTAPE 3:

Alignez les quatre trous du tourillon interne

avec les quatre trous taraudés du boîtier du

luminaire. Fixez le tourillon au luminaire à

l'aide des quatre (4) boulons de 8mm (5/16po)

et des rondelles de blocage fournis avec

l'ensemble du tourillon. Serrez les boulons à

15Nm (132po-lb). Voir Figure 5.

ÉTAPE 4:

Montez le luminaire à l'endroit désiré à l'aide

de (2) boulons de 10mm (3/8po) (fournis par

le client) adaptés à la surface de montage.

VoirFigure 3.

ÉTAPE 5:

Effectuez les branchements de câblage aux

fils du cordon conformément à la section

Branchements électriques.

ÉTAPE 6:

Retirez les vis de réglage n°10-24 des deux

côtés du tourillon.

ÉTAPE 7 :

Desserrez les boulons à tête hexagonale

de 8mm (5/16po) situés des deux côtés du

tourillon.

ÉTAPE 8 :

Pivotez le tourillon à l'angle d'inclinaison

désiré. Alignez les trous de réglage du tourillon

interne et externe.

ÉTAPE 9 :

Insérez une vis n° 10-24, retirée à l'étape 6,

dans les trous correspondants du tourillon

interne et externe. Serrez la vis à 35Nm (30po-

lb). Répétez l'opération avec la vis sur le côté

opposé de l'articulation.

ÉTAPE 10:

Serrez les 2 boulons à tête hexagonale de 8mm

(5/16po) des deux côtés opposés du tourillon à

15Nm (132po-lb).

ÉTAPE 11:

Le réceptacle du verrou tournant doit être

positionné pour que la photocellule soit inclinée

entre +/- 45° de la verticale. Voir Figure6. Si le

réceptacle doit être repositionné pour orienter

la photocellule dans cette plage d'inclinaison,

retirez les vis maintenant le support de montage

du réceptacle sur le tourillon (voir Figure 5),

puis repositionnez le support de montage pour

orienter correctement le réceptacle. Resserrez

les vis à 3,5Nm (30po-lb) après avoir remis en

place la crosse.

ÉTAPE 12:

Installez la photocellule à verrou tournant.

Couvercle du

compartiment

de câblage

(2) vis

Photocellule à bouton

Crosse de fixation

du tourillon

Moitié avant du montage

du bras Fixez ceci à la

tête du luminaire

Pour montage mural,

gardez les trous de serrure

orientés vers le haut

pendant l'installation.

Montage du bras Fixez

ceci à la tête du luminaire

avec (4) boulons

Crosse arrière du

tourillon Fixez ceci à la

surface de montage

(2) Vis de réglage

pour le réceptacle

à verrou tournant

(un de chaque

côté du verrou

tournant)

Réceptacle de la

photocellule à

verrou tournant

Pour montage mural,

gardez les trous de serrure

orientés vers le haut

pendant l'installation.

Vis no10-24

pour régler

l'orientation

(2) boulons

de 8 mm

(5/16 po)

Vis no10-24

pour régler

l'orientation

(2) boulons

de 8 mm

(5/16 po)

Table of contents

Languages:

Other Cree Outdoor Light manuals

Cree

Cree XSP Series User manual

Cree

Cree XSP Series User manual

Cree

Cree EDGE XPS Transportation Series User manual

Cree

Cree NTW Series User manual

Cree

Cree Edge ARE-EDG-AA User manual

Cree

Cree LEDway Series User manual

Cree

Cree NTW Series User manual

Cree

Cree OSQ HO Series User manual

Cree

Cree OSQ HO Series User manual

Cree

Cree Edge Series User manual

Cree

Cree OSQ Series User manual

Cree

Cree RSWL User manual

Cree

Cree VG Series User manual

Cree

Cree XSP Series User manual

Cree

Cree Edge ARE-EDR-R4 User manual

Cree

Cree C-Lite C-WP-A-TR Series User manual

Popular Outdoor Light manuals by other brands

Sealey

Sealey LED37 instructions

nordlux

nordlux VEJERS Mounting instruction

SImx

SImx ELITE LED LHTC637 installation instructions

GEV

GEV CAROLINE 10833 manual

NEBO

NEBO NEB-LSP-0020 Use and care guide

WE-EF

WE-EF PFL540 LED Installation and maintenance instructions

Lindby

Lindby 9949029 Intended use

HEPER

HEPER DOGO Side LW6048.585-US Installation & maintenance instructions

HEPER

HEPER LW8034.003-US Installation & maintenance instructions

Maretti

Maretti VIBE S 14.6080.04.A quick start guide

BEGA

BEGA 84 253 Installation and technical information

HEPER

HEPER MINIMO Installation & maintenance instructions

LIGMAN

LIGMAN BAMBOO 3 installation manual

Maretti

Maretti TUBE CUBE WALL 14.4998.04 quick start guide

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB installation instructions

urban ambiance

urban ambiance UQL1273 installation instructions

TotalPond

TotalPond 52238 instruction manual

Donner & Blitzen

Donner & Blitzen 0-02661479-2 owner's manual