Creality LD-002R User manual
3D Printer
LD-002R
User Manual
Dear customer,
Thank you for purchasing our product. Please read the following instructions carefully
before first use and keep this user manual for future reference. Pay particular attention
to the safety instructions. If you have any questions or comments about the device,
please contact the customer line.
✉www.alza.co.uk/kontakt
✆+44 (0)203 514 4411
Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Praha 7, www.alza.cz
Notes
1. Do not use the printer any way other than described herein to avoid personal injury
or properly damage.
2. Do not place the printer near any heat source or flammable or explosive objects. We
suggest placing in a well-ventilated, low-dust environment.
3. Do not expose the printer to violent vibration or any unstable environment, as this
may cause poor print quality.
4. Please use recommended resin to in case damage of machine.
5. Do not use any other power cable except the once supplied. Always use a grounded
three-prong power outlet.
6. Please do not open the plastic cover during usage, otherwise the printing will be
interrupted.
7. Do not wear cotton gloves when operating the printer. Such cloths may become
tangled in the printers moving parts leading to burns, possible bodily injury, or printer
damage.
8. Please wait a moment after the print is finished. And please wear gloves to take out
the print by tools.
9. Clear the printer frequently. Always turn the power off when cleaning and wipe with a
dry cloth to remove dust, adhered printing plastics or any other material of the frame,
guide rails or wheels. Use glass cleaner or isopropyl to clean the print surface.
10. Children under 10 years should not use the printer without supervision.
Equipment Introduction
1) Hexalobular socket screw 5) Resin vat 9) Air filter
2) Leveling screw 6) Touch screen 10) Power socket
3) Platform plate 7) Metal power switch 11) 5.5-inch screen port
4) Hexalobular socket screw 8) Limit sensor 12) USB port
Equipment parameters
Model
LD-002R
Software language
English
Print method
U disk
X/Y-axis resolution
1440*2560
Z-axis precision
0,03-0,05mm (layer thickness)
Print speed
6-18s (layer height)
Special filaments
Common rigid photosensitive resin, Standard resin, High
elasticity, High hardness, High toughness, Dental model
resin.
Light source
configuration
UV integrated lamp bead (wavelength 405nm)
Operation system
Windows XP and above systems
Nominal power
72W
Print size
119*65*160mm (length, width, and height)
Machine size
221*221*403mm
Package size
295*295*545mm
Machine weight
7kg
Gross weight
8,7kg
Display screen
3.5inch
Package Content
1) Print platform 2) Resin vat 3) 3D printer
Tool list
1) U disk x1 2) 2#, 2.5#, 3# x1 3) Gloves x2 4) Brush x1
5) Plastic blade x1 6) Paper funnel x4 7) Release film x1 8) Mask x2
9) Metal blade x1 10) Power adapter x1
Assemble the 3D Printer
1) Machine Body
2) Plastic Cover
NOTE: Put the plastic cover on the machine body and the installation is completed.
Interface Information
Tools
1) Home
2) Up
3) Down
4) Stop
5) Back
NOTE: The UI information is only for reference, the actual UI may be different.
System
NOTE: The UI information is only for reference, the actual UI may be different.
Print
1) Turn up 1) Delete
2) Turn down 2) Print / Stop
3) Back 3) Back
NOTE: The UI information is only for reference, the actual UI may be different.
Level Platform 1
1. First raise the platform, then loosen rubber screws on the left and right sides of the
resin vat and take out the resin vat.
2. Tool > Manual > Home, and check whether the platform sticks into the printing
screen.
NOTE: The printing platform has been leveled at the factory. IF it needs leveling due to
transportation or other reasons, please follow the steps below to adjust the printing
platform.
Level Platform 2
In the platform does not stick to the print screen, do as the following:
1) After unscrewing the screw, press “Home” to keep the platform and the print screen
parallel.
2) Gently press the platform and tighten 4 screws clockwise, ant the platform can be
leveled successfully.
3) Level up the z-axis a proper position, put the resin vat in, align the screw holes at both
ends of the resin vat, and then tighten the fixing screws at both ends of the resin vat.
Load Resin
Pour the UV photosensitive resin into the resin vat. The slot capacity is 140ml / 170ml /
225ml / 285 ml.
TIPS:
How to change resin:
Takt out the resin vat slowly, pour out the remaining resin into the container, clean the
resin vat, pour in new resin, and then install the resin vat to the machine.
CAUTION:
Resin may cause skin irritation or an allergic skin reaction. Please wear gloves before use
to avoid direct contact with the skin.
Release Film Instructions
Installation steps:
a) First, remove the 14 screws at the bottom of the tray and take out broken release film.
b) Then place the release film between the two steel frames.
c) Finally, put the assembled steel frame back into the tray and tighten 14 screws.
d) The installed release film is as shown.
Parameters
Size
140mm*200mm
Thickness
0.15-0.2mm
Light Transmittance
95%
Start Printing
1) Slice
1) Open the slice software of LCD 3D Printer, click “open” on the left of the screen, and
add model file.
2) If the model needs to add support, click the upper right icon to set corresponding
parameters.
3) Click icon -> click “Settings” -> setting slice parameters (recommend setting
parameters of bottom layer as 10-20).
4) Click “Slice” -> waiting for slice to be finished -> save the sliced file (You are welcome to
find more details of slicing tutorial on the official website www.creality.com).
2) Print
1) Generate G-code and save the g-code file to U disk.
2) Insert the U disk -> press the print button.
Table of contents
Languages:
Other Creality 3D Printer manuals
Creality
Creality CR-6 Max User manual
Creality
Creality HALOT-LITE User manual
Creality
Creality CR-10 Smart User manual
Creality
Creality K1 User manual
Creality
Creality HALOT-ONE PLUS User manual
Creality
Creality CR-10 Series User manual
Creality
Creality Sermoon V1 User manual
Creality
Creality Ender-3 User manual
Creality
Creality BLTouch User manual
Creality
Creality 3D Print Mill User manual
Creality
Creality 3dpRINTmILL User manual
Creality
Creality CR-6 Max User manual
Creality
Creality K1 User manual
Creality
Creality HALOT-ONE PLUS User manual
Creality
Creality BMG CR-10 PrintHead User manual
Creality
Creality CR-10 Max User manual
Creality
Creality CR-10 Max User manual
Creality
Creality CR-30 User manual
Creality
Creality Halot-Sky User manual
Creality
Creality Dual Z User manual
