Craftex CT023N User manual
CT023N, CT019N, CT028N, CT022N, CT026N
DRILL PRESSES
OWNER’S MANUAL
13” 14”
13” 14” 20”
2
TABLE OF CONTENTS
GENERAL SAFETY INSTRUCTIONS PAGE3
SPECIFIC SAFETY INSTRUCTIONS PAGE 4
Features PAGE 5
Electrical Information PAGE 6
Unpacking & Cleaning PAGE 7
Assembly
BasetoColumn PAGE8
TabletoColumn PAGE8
Drill Press Head to Column PAGE 9
Feed Handle PAGE 9
PulleyCover PAGE10
Arbor and Chuck PAGE 10
Removing the Chuck PAGE 10
Mounting the Drill Press PAGE 10
Adjustments
Changing Spindle Speeds PAGE 11
Table Adjustments PAGE 11
Drilling Depth PAGE 12
Spindle Return Spring PAGE 12
Operation
Drilling Speeds PAGE 13
Metalworking PAGE13
Woodworking PAGE 13
Feeding PAGE 13
Laser Operation PAGE 14
Maintenance PAGE 15
Schematic Diagram for CT019N, CT022N & CT026N PAGE 16
PartsList PAGE17
Schematic Diagram for CT023N & CT028N PAGE 19
PartsList PAGE20
Warranty PAGE22
3
GENERAL SAFETY INSTRUCTIONS
EXTREME CAUTION SHOULD BE USED IN OPERATING ALL POWER TOOLS. KNOW
YOUR POWER TOOL, BE FAMILIAR WITH ITS OPERATION. READ THE OWNER’S
MANUAL AND PRACTICE SAFE USAGE PROCEDURES AT ALL TIMES.
CONNECT your machine ONLY to the matched and specified power
source.
WEAR SAFETY GLASSES, HEARING PROTECTION and SAFETY
SHOES when operating heavy machinery. Always wear safety glasses.
DO NOT wear loose clothing or jewellery when operating machinery.
A Safe Environment is important. Keep the area free of dust, dirt and
other debris in the immediate vicinity of the machine.
BE ALERT! Do Not Use prescription or other drugs that may affect your
ability or judgement to safely use this machine.
DISCONNECT the power source when making other adjustments or repairs.
NEVER leave an operating tool unattended.
NEVER reach over the table when the tool is in operation.
ALWAYS keep blades, knives or bits sharp and properly aligned.
ALWAYS keep all safety guards in place and ensure their proper function.
ALWAYS make sure that any tools used for adjustments are removed
before operating the machine.
ALWAYS secure your work with the appropriate clamps or vises.
ALWAYS keep bystanders safely away while operating machinery.
THINK SAFETY. WORK SAFELY. Never attempt a procedure if it does not
feel safe or comfortable.
4
SPECIFIC SAFETY INSTRUCTIONS
Always make certain that you clamp down any object that you are drilling
into.
When drilling, make sure that you are using the correct speed for the
material being drilled.
Clear the drill press table of all objects before turning the tool on.
Keep hands and fingers safely away from the spinning drill bits.
NEVER start the drill press with the drill bit in contact with the work-piece.
Make certain that the drill bit is securely tightened into the drill chuck.
NEVER wear gloves while operating a drill press.
Make certain that the table lock is securely tightened before using the drill
press.
Never attempt to drill any material that is not flat without using a secure jig
for that specific work-piece.
Always remove the drill bit before leaving the machine.
5
DRILL PRESS FEATURES
As part of the growing line of Craftex woodworking equipment, we are proud to
offer the CT023N, CT019N, CT028N, CT022N, CT026N Drill Presses. The
Craftex name guarantees Craft Excellence. By following the instructions and
procedures laid out in this owner’s manual, you will receive years of excellent
service and satisfaction. The CT023N, CT019N, CT028N, CT022N, CT026N are
professional tools and like all power tools, proper care and safety procedures
should be adhered to.
CT023N
Size: 13"
Motor: 1/2 HP
Chuck: 5/8"
Spindle: MT2
Table: 10" SQ.
Speeds: 12
Height: 38"
Weight: 57 kg.
Carton size: 19" x
10" x 30"
CT019N
Size: 14"
Motor: 3/4 HP
Chuck: 5/8"
Spindle: MT2
Table: 11 1/4" SQ.
Speeds: 12
Height: 38"
Weight: 73 kg.
Carton size: 20" x 9"
x 32"
CT028N
Size: 13"
Motor: 1/2 HP
Chuck: 5/8"
Spindle: MT2
Table: 10" SQ.
Speeds: 12
Height: 62"
Weight: 66 kg.
Carton size: 20" x 10"
x 56"
CT022N
Size: 14"
Motor: 3/4 HP
Chuck: 5/8"
Spindle: MT2
Table: 11 1/4" SQ.
Speeds: 12
Height: 64"
Weight: 86 kg.
Carton size: 20" x 10" x
56"
CT026N
Size: 20"
Motor: 1 1/2 HP
Chuck: 5/8"
Spindle: MT4
Table: 18 3/4" x 16 3/4"
Speeds: 12
Height: 67"
Weight: 148 kg.
Carton size: 29" x 13" x
56"
These 5 presses feature Rack & Pinion raising mechanism that gives smooth and accurate
movement of the drill press. The full cast iron table tilt, allowing for a variety of drilled holes.
The operational handles are all made of solid cast iron and feature comfort rubber grip pads
for ease of use.
Each of these drill presses also feature built in laser guiding technology. This can come in
handy when doing single cuts, but more so when repetitive cuts are in order. See page 14 for
more details.
6
GROUNDING INSTRUCTIONS
In the event of a malfunction or breakdown, grounding provides the path of least
resistance for electrical current and reduces the risk of electrical shock. This tool
is equipped with an electrical cord that has an equipment grounding conductor
and a grounding plug. The plug MUST be plugged into a matching outlet that has
been properly installed and grounded in accordance with ALL local codes and
ordinances.
DO NOT MODIFY THE PLUG PROVIDED. If the provided plug will not fit the
electrical outlet, have the proper outlet installed by a qualified licensed
electrician.
IMPROPER CONNECTION of the equipment grounding conductor can result in
risk of electrical shock. The conductor wire with the green insulation (with or
without yellow stripes) is the equipment-grounding conductor. If repair or
replacement of the electrical cord or plug is required, DO NOT connect the
equipment grounding conductor to a live terminal.
If in doubt about these instructions consult a qualified,
licensed electrician.
USE ONLY A THREE-WIRE EXTENSION CORD with
a 3-prong grounding plug and three-hole receptacles
that accept the tool’s plugs as shown.
It is recommended that stationary tools be assigned to a dedicated 15 amp circuit
using #12 wire.
7
UNPACKING AND CLEANING
Carefully unpack your drill press and all of its parts. Compare the carton contents
with the illustration below. Do not discard any packing material until the drill press
is completely assembled and operating properly.
Your drill press and some of its parts have been coated with a protective
lubricant that should be removed before the machine is assembled. This can be
done with a soft cloth moistened with non-corrosive kerosene or mineral spirits.
8
ASSEMBLY
BASE TO COLUMN
Select the base and the drill press column from the
loose parts. Select the four 10mm x 25mm bolts
from the parts bag. Align the holes of the post flange
to the threaded holes in the base. Insert the bolts
and tighten securely.
TABLE TO COLUMN
Remove the ring (3) by loosening the set-screw (4).
Remove the rack (5) from the column.
Check that the worm gear (8) is properly seated
inside the table bracket (7) and it comes in contact
with the gears. The handle shaft (9) should extend
out of the housing by about 1”.
Insert the rack (5) into the geared groove (6) of the
table bracket (7). The table bracket should sit at the
center section of the rack.
Slip the table bracket and rack (1) carefully onto the
column (2). Insert the bottom of the rack into the slot
(3) at the base of the column.
Hold the bracket and rack against the column and
slip the rack ring (4) onto the column.
The rack (1) fits under the rack ring (4). Make sure
there is enough clearance between the rack and the
ring to allow the table to rotate around the column.
Tighten the set-screw (5) to hold the ring in position.
9
ASSEMBLY
Attach the elevation handle by tightening the set-screw (2)
Thread the column lock into the table bracket (1).
Rotate the table and position it directly over and in line with
the base.
DRILL PRESS HEAD TO COLUMN.
Lift the drill press head carefully and position it above the
column. NOTE: this may require the help of a second
person.
The column fits into the drill press mounting hole. Make
certain the mounting hole is properly seated on the column.
Line the drill press head up with the table and base and then
tighten the two set-screws using the supplied hex wrench.
FEED HANDLE.
Fit the one-piece cast-iron feed handle onto the shaft.
10
ASSEMBLY
PULLEY COVER
Insert washer and screw through the hole in the
pulley cover, thread the knob onto the screw and then
tighten.
INSTALLING THE ARBOR AND CHUCK
Slide the long end of the arbor (1) into the spindle (2)
as far as it will go.
Slide the chuck (3) onto the arbor and then place a
block of wood under the chuck and tap the chuck and
arbor with a hammer until it seats into the spindle.
DO NOT STRIKE THE CHUCK DIRECTLY WITH A
STEEL HAMMER.
REMOVING THE CHUCK
Lower the chuck to its lowest position exposing the
spindle sleeve (1).
The spindle sleeve has a large oval hole (2) on both
sides of it.
Rotate the chuck (3) until the spindle hole (4) lines up
with the hole in the spindle sleeve.
Insert the wedge (5) and tap the wedge lightly with a
hammer.
The arbor and the chuck will release from the spindle.
MOUNTING THE DRILL PRESS
Your drill press must be securely fastened to the floor
to prevent the machine from tipping, sliding or walking
during operation. There are two base holes provided
for this.
This manual suits for next models
4
Table of contents
Other Craftex Power Tools manuals
Craftex
Craftex CT024N User manual
Craftex
Craftex CX06SC User manual
Craftex
Craftex CX617 User manual
Craftex
Craftex CT133 User manual
Craftex
Craftex CX series User manual
Craftex
Craftex CT180 User manual
Craftex
Craftex CX series User manual
Craftex
Craftex CT188 User manual
Craftex
Craftex CS Series User manual
Craftex
Craftex CT114 User manual
Craftex
Craftex CT201 User manual
Craftex
Craftex CX series User manual
Craftex
Craftex CT087 User manual
Craftex
Craftex CT056 User manual
Craftex
Craftex CX817N User manual
Craftex
Craftex CX08HC User manual
Craftex
Craftex CX12HC User manual
Craftex
Craftex CX series User manual
Craftex
Craftex CX614 User manual
Craftex
Craftex CX902 User manual
