Cradlepoint COR IBR600 User manual
IBR600 Installation Guide
The Cradlepoint IBR600 router will be delivered to site with SIM card installed and router pre-
configured. The router is administered through a cloud-based portal. The installing technician will not
need to make any configuration changes to the CP
1. Connect power supply to electrical outlet and plug connector into CP
2. Connect WiFi and modem antennas (finger tight only). The paddle-shaped antennas for the
cellular modem are marked 4G and go on the side of the Cradlepoint with the SIM card door.
The thinner WiFi antennas go on the side with the LAN ports
3. Connect the power supply to the IBR600 and switch the power on. Test internet connectivity by
connecting a laptop to the LAN port on the router. Use the port on the left, next to the Reset
button)
4. Mount the router on the wall behind the WRN monitor. Use the bracket included with the
router, and 2 spare screws from the sign installation hardware kits. If the bracket is not
available, use zip ties to mount on the WRN wall plate
5. If the location does not have a WRN monitor, or the Cradlepoint needs to be located elsewhere
for reasons such as poor cell reception in the waiting room, you must notify PatientPoint and
get approval
6. For a standard install, a small wired network will be created –a schematic of a typical network is
shown below. Note that not all installs will have all the devices shown in the schematic
a. The dashed line in the network room represents a future connection linking the office’s
network to the PPT network, at which time the Cradlepoint can be removed. This
connection will NOT be made when the CP is installed
b. Tech will need to make one or two short patch cables to connect the Cradlepoint in the
waiting room to the switch located there and the WRN cpu
7. For some installations, the Cradlepoint will also serve as a WiFi hotspot. There are 2 options -
(they can be turned on individually or simultaneously)
a. Free WiFi network for patients
i. SSID is PatientPoint Welcome
ii. No password required. User must accept Terms and Conditions to access the
internet
b. Hidden WiFi for PPT signs
i. The network ID is not broadcast
ii. The network SSID is patientpointwifi
iii. Security Mode is WPA2 Personal
iv. The network password is DxW!E5fA6U!&nc7K
8. For the PPT devices that use WiFi, configure each sign to connect to the hidden network (see
instructions at the end of this document)
9. Check that connectivity is maintained when all signs are located at their place of installation,
before mounting signs on the wall
10. Use a smart phone or other device to confirm that users can log on to the PatientPoint Welcome
WiFi network
Connecting PPT Signs to a Hidden WiFi Network
Windows XP (WRN & PWR)
1. Choose Control Panel from the Start menu - Control Panel window appears
2. Click the Network Connections icon - Network Connections window appears
3. Right-click the wireless network connection's icon and choose Properties from the pop-up menu
4. Click the Wireless Networks tab
5. Click the Add button, near the bottom of the dialog box
In the Wireless Network Properties dialog box that appears, manually configure the connection
to the unknown wireless network
6. Enter the SSID in the Network name field
7. Choose WPA2 for the security mode and AES data encryption
If the network key box is disabled, as shown in the above figure, another dialog box will appear
and prompt you to enter the password when you connect
On the Connection tab, check the box “Connect when this network is in range”
8. Click OK
At this point, the network should show up as available in the list. You can then connect to it by
clicking its name.
You may need to click “Refresh Network List”
You’ll be prompted for the password when you connect
Windows 7 (IXR)
Open the Network and Sharing Center. Go to Start Menu -> Control Panel -> Network and Internet ->
Network and Sharing Center. Click on 'Set up a new connection or network'
The 'Set Up a Connection or Network' wizard will now start. From the list of available options, select
'Manually connect to a wireless network' and click on Next
Complete all the fields shown in this window
Network name - type the name of the hidden wireless network –typically the 7-digit location ID
Security type - select WPA2-Personal.
Encryption type - AES
Security key DxW!E5fA6U!&nc7K
Windows 7 will automatically connect to the hidden wireless network. Also, the wireless network icon in
the taskbar will change as shown below
Windows 8 (WRN & PWR)
Access the Network and Sharing Center
There are a number of ways to enter the Network and Sharing Center. The fastest method on the
Desktop is to right-click the networking icon in the system tray and click "Open Network and Sharing
Center"
Click "Set up a new connection or network"
Select "Manually connect to a wireless network” and click “Next”
Other manuals for COR IBR600
8
Other Cradlepoint Network Router manuals
Cradlepoint
Cradlepoint R2100 Series User manual
Cradlepoint
Cradlepoint S700 Series User manual
Cradlepoint
Cradlepoint CBR400 User manual
Cradlepoint
Cradlepoint AER1600 Series User manual
Cradlepoint
Cradlepoint CBA850 User manual
Cradlepoint
Cradlepoint R500 User manual
Cradlepoint
Cradlepoint R1900 Series User manual
Cradlepoint
Cradlepoint COR IBR600C Series User manual
Cradlepoint
Cradlepoint AER1600 Series User manual
Cradlepoint
Cradlepoint MBR1400 Series User manual
Cradlepoint
Cradlepoint WIPIPE MBR1000 User manual
Cradlepoint
Cradlepoint E110 User manual
Cradlepoint
Cradlepoint WIPIPE MBR1000 User manual
Cradlepoint
Cradlepoint COR IBR600 User manual
Cradlepoint
Cradlepoint AER 2100 System manual
Cradlepoint
Cradlepoint CBR400 User manual
Cradlepoint
Cradlepoint MBR1400 Series User manual
Cradlepoint
Cradlepoint CRADLEPOINT IBR650 User manual
Cradlepoint
Cradlepoint COR IBR350 User manual
Cradlepoint
Cradlepoint AER 2100 User manual
