CoolShirt MobileCool BP2 User manual
MobileCool BP2
Congratulations on your purchase of the world’s finest Personal Cooling System
The COOLSHIRT MobileCool BP2 is an active personal cooling system comprising two main
components; a cooling garment with patented non-kink tubing attached and a backpack that
contains a rechargeable Lithium battery pack, battery charger, pump, ice/water bladder and
an on/off switch.
The garment and backpack are connected after donning by a set of quick-disconnect fittings. When
connected together, the garment tubing and backpack bladder form a closed loop of coolant (water)
that is circulated via a pump and battery pack.
P ease inspect your purchase to ensure that your system contains the components
isted be ow. If there are any discrepancies, p ease contact COOLSHIRT SYSTEMS
Customer Service at 800-345-3176 immediate y.
Inc uded with your system:
© 2016 COOLSHIRT SYSTEMS, 170 Andrew Drive, Stockbridge GA 30281
Office : 800-345-3176 Fax: 678-289-4325 www.coolshirt.com
uantity
_________ 1
_________ 1
_________ 1
_________2
Part #
2001-0005
5004-0001
5004-0002
5012-0031
Description
MobileCool BP2 Cooling Unit with internal pump
Rechargeable Battery 7 Hour
Battery Charger
Endurance Ice - 24 Ounce
All products are guaranteed or one year rom the initial date o purchase or
de ects in material and workmanship. I you have any questions, please call
COOLSHIRT SYSTEMS Customer Service at (800) 345-3176. We appreciate your interest
in our personal cooling products.
MobileCool BP2
Operating Instructions:
1. Charge the battery pack with the supplied battery charger:
a. The battery pack is located in a pouch on the inside of the backpack, at the top
b. The battery pack can be left in place for charging or removed from its pouch.
c. imply detach the wire terminal from the battery pack and attach the charger to the
battery at the same terminal location
d. The first charge will take several hours, then a few hours for subsequent charges. A
solid green light on the charger indicates the charge is complete.
2. Place Endurance Ice in freezer until frozen solid. Place Endurance ice back in
water bladder. NOTE: COOLSHIRT recommends putting ice cubes in the
bladder with Endurance Ice
3. Re-install the battery pack.
4. Add 1/2 ounce of Maintenance Additive (5003-0001) then fill bladder with enough cold
water to cover the pump then seal the bladder.
5. Priming the System:
a. On a flat surface lay out the garment and backpack such that the quick disconnect fittings
are facing each other.
b. Prop up the backpack such that the water in the bladder settles at the bottom of the
bladder (ie: toward the pump at the bottom of the backpack).
c. Connect the garment and backpack together using the quick disconnect fittings.
d. Using the toggle switch, turn on the system and allow it to run for a few minutes, taking
note that the water coolant is moving throughout the garment. Turn the system off and
inspect the bladder to see if it is filled half-way with water. If not filled half-way, top off as
required.
6. Close the backpack flap by using the dual zipper pull.
7. Putting the system on:
•Put on the garment and backpack. For optimum cooling performance, the garment should
fit snug to the body and be situated against the skin, beneath all other clothing.
• Connect the fittings from the garment and backpack. The fittings will ‘click’ upon a good
connection.
MobileCool BP2
Operating Instructions (continued):
8. Turn on the system using the toggle switch for cooling. If you are receiving too much
cooling, turn the system off using the toggle switch.
9. Taking the system off:
• Turn the system off using the toggle switch.
• Push the tabs on the quick disconnect fittings until they pop apart.
• Remove garment and backpack.
10. For extended cooling:
• Open the bladder and replace the melted Endurance Ice with a frozen Endurance Ice
• If using ice cubes, open the bladder and dump excess water. Re-fill with ice cubes and top
off with water as per instruction #4.
Maintenance:
1. Laundering the garment:
a. Turn the shirt inside out.
b. OPTIONAL: Place in a laundry bag.
c. Launder or clean the cooling garment per the care instructions located in the garment
packaging.
2. Cleaning the bladder and garment tubing:
a. If mold appears in the bladder or garment tubing, pour 2 ounces of liquid Maintenance
Additive into a prepared bladder (with Endurance Ice inserted and topped off with water),
then operate the system during your next cooling cycle.
b. The Maintenance Additive (5003-0001) contains a fungicide and is specially formulated to
clean and sanitize your COOL HIRT MobileCool BP2. It is nontoxic and biodegradable.
Reference caution below .
c. Maintenance Additive (5003-0001) can e purchased from COOL HIRT Y TEM by
calling (800) 345-3176.
MobileCool BP2
Troubleshooting:
Pump stops working
If the pump stops working check the following to resolve:
a. Make sure that batteries are fully charged. If not, insert fully charged batteries.
b. Press the toggle switch to see if pump was accidently shut off.
c. Look for pinch points in the tubing.
d. Verify that the electrical connections have not been severed.
e. Make sure that all quick disconnects are properly connected.
Garment is not cooling
If the cooling garment does not have a cool temperature, check the following:
a. Make sure that the Endurance Ice or ice cubes have not melted completely.
b. Press the toggle switch to see if pump was accidentally shut off.
c. Look for pinch points in the tubing.
d. Make sure that all quick disconnects are properly connected.
e. Make sure that the garment and bladder are completely filled with water coolant.
CAUTIONS
• Disconnect the battery pack if the system will not be used for several days or longer.
• When using the maintenance additive, keep out of the reach of children.
Contains a surfactant. Do not get in eyes. If eye contact occurs, rinse eyes with water for 5
minutes. If eye irritation persists, seek medical attention.
Table of contents
Other CoolShirt Freezer manuals
