Control Techniques UD70 User manual

www.controltechniques.com

Installation Guide

UD70

MD29

Second Processor Options

for Unidrive and Mentor II

Part Number: 0460-0098

Issue Number: 3

Safety Information

The option card and its associated drive are intended as components for professional

incorporation into complete equipment or systems. If installed incorrectly the drive may

presenta safety hazard.The drive uses high voltages and currents, carries a high level

of stored electrical energy, and is used to control mechanicalequipment that can cause

injury.

Close attention is required to the electrical installation and the system design to avoid

hazards either in normaloperation or in the event of equipment malfunction. System

design, installation, commissioning and maintenance must be carried outby personnel

who have the necessary training and experience. They must read this safety information

and this Installation Guide carefully.

Careful consideration must be given to the functions of the drive and option card which

mightresultin ahazard,eitherthrough their intendedfunctions,e.g.auto-start,orthrough

incorrectoperationdue toa fault ortrip,e.g.stop/start, forward/reverse,maximum speed,

loss of a communications link.

In any application where a malfunction of the drive or option card could lead to damage,

loss orinjury, a riskanalysis mustbe carried out, and where necessary, furthermeasures

takento reduce the risk.To ensure mechanicalsafety, additional safety devicessuch as

electro-mechanical interlocks may be required. The Drive must not be used in a safety-

critical application withoutadditional high-integrity protection against hazards arising

from a malfunction.

General Information

The manufacturer accepts no liability for any consequences resulting from inappropriate,

negligent or incorrect installation or adjustment of the optional operating parameters of

the equipment or from mismatching the Drive with the motor.

ThecontentsofthisUserGuidearebelievedtobecorrectatthetimeofprinting. Inthe

interests of a commitment to a policy of continuous development and improvement, the

manufacturer reserves the right to change the specification of the product or its

performance, or the contents of the User Guide, without notice.

All rightsreserved. No part of this User Guide may be reproduced or transmitted inany

form or by any means, electrical or mechanical including photocopying, recording or by

any information storage or retrieval system, without permission in writing from the

publisher.

Issue Code: 3

Hardware: UD70 All Issues, MD29 Issue 3 and later

Firmware: N/A

UD70/MD29 Installation Guide

Issue Number: 3 www.controltechniques.com

Contents

1 Mechanical Installation 1

1.1 Unidrive and UD70 1

1.2 Mentor II and MD29/MD29AN 3

2 Electrical Installation 5

2.1 UD70 5

2.2 MD29 5

2.3 MD29AN 6

2.4 RS232 Port Connections 6

2.5 RS485 Port Connections 6

2.6 I/O Box Port Connections (MD29 Only) 8

2.7 Digital I/O Connections 8

3 RS485 Port Configuration 9

3.1 Node Address 9

3.2 Data Rate 10

3.3 RS485 Port Communications Modes 10

3.4 Storing configuration parameters 12

1UD70/MD29 Installation Guide

www.controltechniques.com Issue Number: 3

1 Mechanical Installation

Before attempting to install option modules or cards, ensure that the Unidrive

or Mentor II is switched off. AC Drives should be left for 5 minutes to ensure

that the DC link capacitors have completely discharged.

1.1 Unidrive and UD70

• Slide the UD70 module under the displaypanel ofthe Unidrive, and push the

module in until the connector locates with the plug inside the Unidrive.

NOTE

UD70/MD29 Installation Guide 2

Issue Number: 3 www.controltechniques.com

• Apply firm pressure, and the module will click securely into place.

• To remove the UD70, pull firmly on the black tab, and the module will

disengage from the connector.

Do notattemptto remove the UD70 module while the Unidriveis still powered

up, as this may cause damage to the Unidrive.

WARNING

3UD70/MD29 Installation Guide

www.controltechniques.com Issue Number: 3

1.2 Mentor II and MD29/MD29AN

The MD29 is fitted onto the 40-way pin header (PL1) on the MDA2B circuitboard.

The supplied mounting pillars should be attached to the MDA2B on the Mentor II.

• Tilt the MD29 at an angle and locate the first few pins into the MD29 header.

UD70/MD29 Installation Guide 4

Issue Number: 3 www.controltechniques.com

• Tilt the board to horizontal to engage the rest of the pins. Press firmly

downwards to firmly fix the MD29 to the header and 4 mounting pillars.

Take care when locating the board onto this connector - do not force it on.

Excessive force may bend and break the pins of the header.

When removing an MD29, unsnap the MD29 from the pillars before gently working

the MD29 off the header. Do not tilt the MD29 excessively to one side,as this may

bend and break the end groups of pins on the header.

Do not attempt to remove the MD29 while the Mentor II is stillpowered up, as

this may cause damage to the Mentor II.

NOTE

WARNING

5UD70/MD29 Installation Guide

www.controltechniques.com Issue Number: 3

2 Electrical Installation

2.1 UD70

The UD70 provides a dedicated RS232 programming port (Connector C) and a

general purpose RS485 communications port (Connector D)..

Connectors A and B provide the connectors for high speed fieldbus communication

options, if fitted. Refer to the appropriate fieldbus option User Guide for full fieldbus

connection details.

2.2 MD29

The MD29 provides a dedicated RS232 programming port (Connector SK2) and a

generalpurpose RS485 communications port (Connector PL1). In addition, the

MD29 also has a dedicated RS485 port (Connector TB1) for use with the Control

Techniques I/O Box.

MD29

PL1 SK2TB1

SK2

SW1

UD70/MD29 Installation Guide 6

Issue Number: 3 www.controltechniques.com

2.3 MD29AN

The MD29AN provides a dedicated RS232 programming port (Connector SK2) and

a generalpurpose RS485 communications port (Connector PL1). In addition, the

MD29 also has a dedicated CTNet port (PL2).

2.4 RS232 Port Connections

The pin connections for the RS232 portare given in the table below. The RS232

portcan be connected to a 9 way serial portusing a 9-way one-to-oneribbon cable

lead.

2.5 RS485 Port Connections

The pin connections for the RS485 portare given in the table below 0VSC is

completely isolated from the main Unidrive and Mentor II 0V.

MD29AN

PL1 SK2PL2

SK1

Pin Function Description

2 TxD Transmit line

3 RxD Receive line

50V0V

Pin Function Description

1 0VSC 0VSC Isolated 0V for serial communications link.

2 TxA /Tx Inverted transmit line

3 RxA /Rx Inverted transmit line

6 TxB Tx Transmit line

7 RxB Rx Receive line

7UD70/MD29 Installation Guide

www.controltechniques.com Issue Number: 3

2.5.1 4 Wire RS485 Network

The diagram below shows the connections required for a 4 wire RS485 network,

using a master controller with an RS485 port. The UD70 and MD29 can be

configured to act as master controllers, but this requires DPL programming to

control the network.

An RS232-to-RS485 converter is required to allow a standard PC serial port to

communicatewitha4wireRS485network.

2.5.2 2 Wire RS485 Network

The diagram below shows the connections required for a 2 wire RS485 network,

using a master controller with an RS485 port. The UD70 and MD29 can be

configured to act as master controllers, but this requires DPL programming to

control the network.

An RS232-to-RS485 converter with “intelligent transceiver switching” (also known

as “magic” RS485 converters) is required to allow a standard PC serial port to

communicatewitha2wireRS485network. Anexampleofa“magic”converteris

the MA485F converter from Amplicon.

A “magic” converter is not required is the master contoller has an RTS control

output. This output is enabled when the master is transmitting, and disabled

when the master is not transmitting. Control Techniques software packages

(UniSoft, MentorSoft and SystemWise) do NOT switch the RTS line.

RxARxBTxATxB0V RxARxBTxATxB0V

RxA

RxB

TxA

TxB

Master

UD70, MD29,

Unidrive, Mentor II

Slave

UD70, MD29,

Unidrive, Mentor II

12637 12637

Slave

120Ω0.25W

termination resistors

TxRxA0V

RxA

RxB

TxA

TxB

Slave

Master

UD70, MD29,

Unidrive

Slave

Commander SE

TxRxBRxARxBTxATxB0V

12637 3 7 2

120Ω0.25W

termination resistor

NOTE

Other manuals for UD70

This manual suits for next models

Table of contents

Other Control Techniques Control Unit manuals

Control Techniques

Control Techniques UD77 DeviceNet User guide

Control Techniques

Control Techniques EMERSON DeviceNet User manual

Control Techniques

Control Techniques UD70 User manual

Control Techniques

Control Techniques EMERSON SPM User manual

Control Techniques

Control Techniques Modbus TCP User manual

Control Techniques

Control Techniques UD55 User manual

Control Techniques

Control Techniques UD53 User manual

Control Techniques

Control Techniques Unidrive M400 User manual

Control Techniques

Control Techniques FM-3 User manual

Control Techniques

Control Techniques Epsilon EP-I User manual

Control Techniques

Control Techniques UD78 User manual

Control Techniques

Control Techniques USB User manual

Control Techniques

Control Techniques Profibus-DP User manual

Control Techniques

Control Techniques DeviceNet User manual

Control Techniques

Control Techniques UD52 User manual

Control Techniques

Control Techniques UD51 User manual

Control Techniques

Control Techniques Modbus RTU User manual

Control Techniques

Control Techniques SM-Resolver User manual

Control Techniques

Control Techniques UD77 DeviceNet User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual