Contacta STS-K009-IP-L-B Operation manual
Installation &
User Guide
September 2021
Window Intercom System
Surface Mounted Entry System - STS-K009-IP-L-B
2
Contents
Product Overview
Components
Connections
Installation Instructions
Speaker & Microphone Kit Installation
AmplierInstallation
Speaker & Mic. Kit Installation
Hearing Loop Installation
AmplierSetup
Cleaning / Maintenance
Troubleshooting
Engineer’s Mode
3
3
4
5
6
6
7
10
11
13
14
15
Contactahasapolicyofcontinuousproductdevelopment,andthereforesmallspecication
changesmaynotbereectedinthismanual.Images,labels,packaging,accessoriesandproduct
colours are subject to change without notice.
3
Product Overview
This speech transfer system provides high quality sound across partitions or
safety screens. It includes our surface mounted entry unit with IP-55 rating,
ouropenduplexamplier,ahearingloop,andafree-standingmicrophone
andspeakerunitforsta.
The surface mounted entry unit (K009-IP) must be installed as per installation
instructions to maintain its IP-55 rating.
1. Installation and User Manual
2. Amplier
3. Hearing Loop Sticker
4. IEC Lead
5. Power Supply
6. Hearing Loop Aerial
7. Mounting Bracket
Fixing Kit:
• Adhesive Clip x 10
• No.6 x 1/2” Countersunk Screws x15
• P-Clips x6
• M3 x 24mm Universal Wall Plugs x4
• M3 x 25mm Fixing Screws x4
4
36
7
5
2
1
General Components
Speaker & Microphone Components
1. StaMicrophone
2. Surface Mounted Entry Unit
3. Screw Sticker Covers x4
2
1
3
4
Connections
StaMicrophone
Hearing Loop
Power Supply
Surface Mounted
Entry Unit
Cable Colour Amplifier Socket Amplifier Pin #
Blue Customer speaker 3-4
Brown Customer mic 14-15
Green Call/LED 9-10
Orange LEDs 11-12
Surface Mounted Entry Unit to Amplifier - Connections Colours
5
Werecommendthatinstallationiscarriedoutbyaqualiedengineer,
adhering to relevant standards.
Check the contents of the box to familiarise yourself with the components.
Installation Instructions
Negative -
or screened cable
Positive +
A toolkit recommended to install the system will include:
Trim cables if necessary (excluding the power supply)
to the required length to connect to the back of the
amplier.Bareapproximately6mmofthecableendsto
connect to the 2 pin plugs.
• Pliers
• Tape Measure
• Pencil or Marker Pen
• Torch
• Cable Ties
• Electrical Insulation Tape
• Trunking
• Screwdrivers (Flat or Blade 2.5mm
and Phillips Head PH2)
• Battery or Mains Drill
• Drillbits: 2mm, 3mm, 5mm and 7mm
• Allen Key Set
• Cable Tacking Gun (10mm)
• Wire Cutters/Strippers
Recommended Tools
6
1. Placetheamplierunderastacounter,ensuringthatitwillnotobstruct
stawhentheyaresitting.
2. Markthefourxingpointsfortheamplierunderthecounter.
3. Drillandxtheamplierinplaceusingthesuppliedscrews.
4. Installtheamplier’spowersupplyclosetoapowersocketoutletusing
thesuppliedmountingbracketandxingscrews.
Fixing points
Amplifier Installation
AmplierInstallation
LED connection or alert tone (if required)
CondenceLEDtoconrmthesystemispowered
oranalerttonefortheattentionofsta
Stamicrophoneconnection
Customer microphone connection
CondenceLED(ifrequired)forstatusalerts
and fault detection
Hearing loop aerial
Line in connection for
external audio source
Staspeakerconnection
Customer speaker connection
Power input
connection
Use power supply
through ground
supply only
7
Microphone & Speaker Installation
1. Placethestamicrophoneonthestasideof
the partition, ensuring that it does not cause an
obstructionandisasclosetostaaspossible.
It is ideally positioned no more than 300mm
awayfromthestamember.
2. Usethecablemanagementholetorunthesta
microphonecablebacktotheamplier.Ifthere
Sta
microphone
is not already a cable management hole, drill in a suitable location near
the rear of the counter.
3. Find a suitable location for surface mounted entry unit (K009-IP).
It is ideally placed at head height (approximately 1.65m) from the ground
to allow most customers to easily press and speak into it. The unit should
beinstalledagainstawalloratsurfacetoensuremaximumingress
protection.
4. Remove the x4 screws that hold the front cover of the unit together and
put these to the side.
5. Carefullyremovethefrontcoverandlocatethex4xingpointholes.The
front cover should be handled with care as it will be wired to the back
box.
8
Fixing
points
Cable
management
hole
6. Markthex4xingpointholesandcablemanagementholeonthe
mounting surface.
7. Prepare your mounting surface by installing any wall plugs necessary into
thexingpointsmarked.
Note: This kit is provided with x4 universal surface M3 x 24mm wall plugs
whichrequirea5mmpilothole.Pleaseensureappropriatexingsare
used for your intended surface.
Ensure that cables are routed into the cable management hole prior to
securing the back box to the mounting surface.
8. Usex425mmxingscrewstosecuretheboxtoitsintendedsurface
using the holes created in the step 7.
Cable
management
hole
Cable
9
9. Use the x4 removed screws from step 4 to re-attach the front cover to
the back box. Ensure the seal is in place and in good condition. Tighten
accordingly.
10. Take the x4 supplied screw cover stickers and cover the visible silver
screws (highlighted in the image below).
10
Theaerialshouldbexedunderthedesk-toporcountercentrallyonthe
custome or visitor side, one half mounted horizontally under the counter and
theotherhalfmountedvertically,facingthecustomer/visitor(asintherst
scenario below).
Position the aerial under the counter using either the provided P-clips
oranotherxingmethodofyourchoice.Seethediagrambelowfor
recommended positioning.
A is the optimum layout for a counter hearing loop.
B and C are acceptable only if A is not possible and the layout is aligned so
thatthemagneticeldwillbedirectedtowardsuser’sheadheights.
Ensure all hearing loop signage is displayed clearly.
XX
Hearing Loop Installation
A B C
Table of contents
Other Contacta Intercom System manuals
Contacta
Contacta STS-K001L Operation manual
Contacta
Contacta IL-EL42-PB User manual
Contacta
Contacta STS-K020 Operation manual
Contacta
Contacta STS-K020 Operation manual
Contacta
Contacta STS-K002L Operation manual
Contacta
Contacta STS-K070 Operation manual
Contacta
Contacta STS-K080-IP Operation manual
Contacta
Contacta STS-K060 Operation manual
Contacta
Contacta STS-K071 Operation manual
Contacta
Contacta STS-K035-B Operation manual
