Conrad FS20 ST User manual
OPERATING INSTRUCTIONS
Version 08/07
Wireless switch socket
„FS20 ST“
Item no. 62 30 04
2
Introduction
Dear customer,
Thank you for purchasing this product.
This product meets the requirements of both current national and
European guidelines.
Please read the user manual completely and observe the safety and
operation instructions before using the product!
This user manual belongs to this product. It contains important
information specific to its operation and handling. Please bear
this in mind when passing on the product to a third party.
Therefore keep this user manual for future reference!
All company and product names contained herein are trademarks of
their respective owners. All rights reserved.
For more inquiries, contact or consult our technical service:
Germany: Tel. no.: +49 9604 / 40 88 80
Fax. no.: +49 9604 / 40 88 48
e-mail: [email protected]
Mon. to Thur. 8.00am to 4.30pm
Fri. 8.00am to 2.00pm
3
Table of contents
Page
1. Prescribed use ................................................................................. 4
2. Scope of delivery ............................................................................. 4
3. Explanation of icons ......................................................................... 5
4. Safety instructions ........................................................................... 5
5. Control panel .................................................................................... 7
6. Registering a FS20 transmitter ....................................................... 8
7. Operation .......................................................................................... 9
a) Remote control operation .......................................................... 9
b) Controlling the FS20 device ...................................................... 9
c) Direct operation ......................................................................... 9
8. Timer function ................................................................................ 10
a) Programming the timer ............................................................ 10
b) Timer operation ........................................................................ 11
Starting the timer ..................................................................... 11
Prematurely stopping the timer ............................................... 11
Deactivating timer function ..................................................... 11
Temporary switching to permanent service ........................... 12
9. Integrating the wireless switch socket into the
FS20 address system .................................................................... 13
a) Assigning further addresses/address types .......................... 13
b) Deleting addresses and address types .................................. 13
10. Resetting the default settings ........................................................ 14
11. Handling ......................................................................................... 15
12. Maintenance and cleaning ............................................................ 16
13. Disposal .......................................................................................... 16
14. Information on the range ............................................................... 17
15. Declaration of conformity (DOC) .................................................. 19
16. Technical specifications and features .......................................... 19
4
1. Prescribed use
The wireless switch socket ‘FS20 ST’ functions exclusively in conjunction
with the FS20 wireless control system.
The wireless control system can switch a device that is connected to the
wireless switch socket on or off or dim the device without the use of cables
(refer to technical specifications and features).
Another feature is the integrated programmable timer function.
No part of the product may be modified or adapted and the casing must not
be opened.
The safety instructions and installation notes in this user manual must be
observed without fail.
Any use other than the one described above may damage the
product and can also possibly create additional dangers, for
example, short-circuit, fire, electrical shock, etc.
Readtheseoperatinginstructionsthoroughlyandcarefully,as
they contain a great deal of important information for the
operation and handling.
2. Scope of delivery
• Wireless switch socket ‘FS20 ST’
• User manual
5
3. Explanation of icons
The icon with a lightning flash in a triangle is used to alert you
to potential personal injury hazards such as electric shock.
The icon with an exclamation mark in a triangle points to
important instructions in this user manual that must be ob-
served.
The ‘hand’ symbol indicates special tips and information on
operation.
4. Safety instructions
The product’s guarantee becomes invalid if the product is
damaged as a result of failure to observe these operating
instructions.Wedonotassumeanyliabilityforany result-
ing damages!
Nor do we assume liability for damage to property or
personal injury caused by improper use or failure to ob-
serve the safety instructions. In such cases the product’s
guarantee becomes invalid!
• For safety and licensing (CE) reasons any unauthorised alterations to
and/or modification of the product are not permitted.
• Do not use this product in hospitals or medical institutions. Although the
product emits only relatively weak radio signals, these may cause life-
support systems to malfunction. This may also be the case in other
areas.
6
• The product is designed in accordance with protection class I. The only
voltagesourcethatmay be used is that of the correct power socket-outlet
(230V~/50Hz) with the protective earth conductor of the public power
supply system.
• The product is not a toy and should be kept out of the reach of children.
Therefore take particular care when children are around!
• Make sure the product does not become damp or wet; it is only suitable
for use in dry indoor locations (not bathrooms or similar). Otherwise
there is the risk of a life-threatening electric shock!
• Protect the product against heat, cold, and direct sunlight while in
storage or operation.
• Never dismantle the product! There is danger of a fatal electric shock!
• Do not leave packaging material lying around. This may become a
dangerous plaything in the hands of children.
• The accident-prevention regulations, established by the Employer’s
Liability Insurance Association for electrical equipment and facilities,
must be adhered to in commercial facilities.
• Consult a skilled technician if you have doubts about the mode of
operation, safety or connection of the device.
• Handle the product with care; knocks, blows or even a fall from a low
height can damage it.
7
5. Control panel
Control keys with integrated LED
Socket for consumer loads
(230V~/50Hz, max. 16A)
On the back side there is a shock-proof plug that must be plugged into a
socket of the public power supply system (230V~/50Hz).
Quick function test
• Plug the ‘FS20 ST’ into a power socket with an earth connector (operat-
ing voltage 230V~/50Hz).
• For example, using a lamp as a load, plug it into the socket on the front
side of the wireless switch socket.
• Briefly press the control button on the wireless switch socket.
It should be possible to switch the load (for example, the lamp)
on and off by briefly pressing the button (1. ‘on’, 2. ‘off’, 3. ‘on’,
etc.).
8
6. Registering a FS20 transmitter
Toregisterthewirelessswitchsocket‘FS20 ST’ with a FS20 transmitter (for
example, a remote control from the FS20 wireless control system or other
devices, such as the load monitor ‘FS20 FMS’), proceed as follows:
• Press and hold the control button on the ‘FS20 ST’ for at least 15
seconds. The control indicator/LED on the wireless switch socket starts
to blink and the device is now in programming mode.
Alternatively, the wireless switch socket can also be plugged
into the socket with the control button already pressed. This
way the device switches immediately to programming mode
(control indicator/LED blinks).
•Briefly press a button of the desired key combination on your remote
control or corresponding control button of a FS20 device (for example,
load monitor ‘FS20 FMS’).
When the wireless switch socket receives the code the control indicator/
LED stops blinking.
The wireless switch socket is now programmed to this remote control or
the corresponding FS20 device.
• If required, the programming can be replaced at any time by another
button on the remote control, or by another remote control channel. To
do this, proceed again as described above.
Additional functions (for example, timer programming) are
described later in this user manual.
9
7. Operation
a) Remote control operation
Switching on: Briefly press the right button of the programmed button
combination
Switching off: Briefly press the left button of the programmed button
combination
b) Controlling the FS20 device
Theprocedure varies, depending upon theFS20 device. Pleaserefer to the
user manual of the specific FS20 device.
For example, the load monitor ‘FS20 FMS’:
Switching on: Briefly press the control key on the ‘FS20 FMS’
Switching off: Briefly press the control key on the ‘FS20 FMS’
c) Direct operation
Switching on: Briefly press the control key on the wireless switch socket
Switching off: Briefly press the control key on the wireless switch socket
The switch alternates every time the control key is pressed
(‘toggle’ function).
When the wireless switch socket is switched on, pressing the
button will switch it off (and vice versa).
10
8. Timer function
The wireless switch socket can also be used as a timer.
As soon as a switching time has been programmed, the ‘FS20
ST’ remains switched on for the programmed length of time
after each power-on command. After this time has expired, it
automatically switches off.
The timer is programmable for an on-time of between 1 second and 270
minutes (4 hours 30 min).
In order to program the timers you require a remote control
from the FS20 wireless control system. Please refer to the
corresponding user manual.
It is possible to program the timer for the load monitor
‘FS20 MS’ with its command menu; the following section
does not apply to the ‘FS20 FMS’.
a) Programming the timer
•Simultaneously press and hold both buttons of the respective button
combination on your FS20 remote control for one to five seconds (1 to 5
sec).
• The control indicator/LED on the wireless switch socket blinks. The time
measurement for the desired on-time begins.
• After the desired amount of time has expired press both buttons on the
remotecontrol again simultaneously foroneto fiveseconds (1to5 sec).
The on-time is now programmed.
This manual suits for next models
1
Table of contents
Other Conrad Switch manuals
Conrad
Conrad 97 51 23 User manual
Conrad
Conrad RSLT2 User manual
Conrad
Conrad 91 79 13 User manual
Conrad
Conrad 77 70 39 User manual
Conrad
Conrad 97 60 62 User manual
Conrad
Conrad 97 52 43 User manual
Conrad
Conrad X-OVER User manual
Conrad
Conrad 986131 User manual
Conrad
Conrad 39 35 39 User manual
Conrad
Conrad 98 61 63 User manual
Conrad
Conrad 97 54 21 User manual
Conrad
Conrad 1007639 User manual
Conrad
Conrad RSLR2 User manual
Conrad
Conrad 552922 User manual
Conrad
Conrad RSL2 User manual
Conrad
Conrad 97 51 00 User manual
Conrad
Conrad RSLT4 User manual
Conrad
Conrad 42 58 46 User manual
Conrad
Conrad 30 05 18 User manual
Conrad
Conrad 97 52 42 User manual
