ConeMount S Super User manual

Model S “Super” Bearing Heater Instructions

General:

Carefully unpack your Cone Mount Bearing Heater and remove all packaging materials

and wrappings.

1. Always wear heavy safety gloves to avoid risk of burn or shock

2. Remove the Cone Safety Guard from the ConeMount Bearing Heater.

3. Place the bearing or gear to be heated on the cone of the ConeMount Bearing

Heater.

4. Place the thermostat box unit on the bearing. Be sure the thermostat rests on the

bearing inner race.

NOTE- Some bearings may be too small for use with the thermostat unit. In those cases,

mark the bearing inner race with the temperature crayon which is provided

*NEVER place the thermostat directly on cone unit

5. Plug the ConeMount Bearing Heater into an electrical outlet of correct voltage.

6. Turn the switch on the control box to the ON position.

7. A red control light will be visible on the control box unit. When the light goes out

the bearing can be easily positioned on the shaft.

*NOTE –if the thermostat is not being used the control light will stay on. When the

temperature crayon mark melts, the bearing is ready for mounting.

8. Turn the switch on the control box to the OFF position

9. Disconnect the cord from the electrical outlet.

10. Replace the Cone Safety Guard over the ConeMount Bearing Heater to warn of

possible high temperatures.

**NOTE –The ConeMount Bearing Heater is not recommended for continuous use

Bearings in excess of 100lbs should be supported on the outer race to prevent damage

to the cone unit.

Care:

Periodically, wipe the cool unit with a clean, dry, soft cloth to remove possible dirt or

grease residue. The thermostat should be gently cleaned to assure proper calibration.

IMPORTANT SAFETY INSTRUCTIONS:

1. DRESS PROPERLY. Always wear heavy safety gloves to avoid risk of burn or

shock.

2. AVOID DANGEROUS ENVIRONMENTAL CONDITIONS. Do not use the

ConeMount Bearing Heater in damp or wet locations, in or around water.

3. DO NO OPERATE the ConeMount Bearing Heater in gaseous or explosive

atmospheres, around combustible or flammable liquids, or hazardous

materials.

4. DO NOT OPERATE the ConeMount Bearing Heater on any surface which may

burn. Always place the unit on a flat surface for use.

5. DO NOT leave unit unattended

6. DISCONNECT TOOL. Always disconnect the power cord from the wall receptacle

when the unit is not in use.

7. USE THE RIGHT TOOL. Do not use the ConeMount Bearing Heater for any job

except that for which it is intended.

8. DON’T ABUSE CORD. Do not yank the power cord from the wall receptacle.

Keep cord from heat, oil and sharp edges. Do not operate unit if power cord or

plug show signs of damage.

9. WARNING: Keep unit dry, clean, and free from oil and grease. Keep work area

clean.

10. SAVE THESE INSTRUCTIONS.

Table of contents

Other ConeMount Heater manuals

ConeMount

ConeMount B User manual

Popular Heater manuals by other brands

oventrop

oventrop Regucor Series quick start guide

Blaze King

Blaze King CLARITY CL2118.IPI.1 Operation & installation manual

ELMEKO

ELMEKO ML 150 Installation and operating manual

BN Thermic

BN Thermic 830T instructions

KING

KING K Series Installation, operation & maintenance instructions

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Installation instructions and owner's manual

Well Straler

Well Straler RC-16B user guide

EUROM

EUROM 333299 instruction manual

Heylo

Heylo K 170 operating instructions

Eterna

Eterna TR70W installation instructions

Clarke

Clarke GRH15 Operation & maintenance instructions

IRSAP

IRSAP The Radiator Company Ovali Fitting instructions

Empire Heating Systems

Empire Heating Systems WCC65 Installation and owner's instructions

Wetekom

Wetekom 92 86 43 Original instructions

Desa

Desa SPC170-F owner's manual

Watlow

Watlow Watrod Electric Tubular Heaters Specifications

Haverland

Haverland ECO-DRY GPS Series Instruction & installation manual

Stelpro

Stelpro ASILVC2060 Series user guide