Conde Desk V2 Screen Quick start guide
Condeco Desk V2 Screen
Operational Description
Version 1.0 prepared by Xiaofei Zhang
Contents
This is a Heading 1......................................................................................................................................5
This is a Heading 2...................................................................................................................................
1. This is a Heading 1 Numbered.........................................................................................................
1.1. This is a Heading 2 Numbered.................................................................................................
Here’s a table:................................................................................................................................................
About Us .....................................................................................................................................................16
Powering Change ................................................................................................................................16
Who We Work With ..............................................................................................................................16
Desk V2 Screen Design Spec
1. Display: 2.8” LCD 320 x 240 (QVGA) , 4 Wire SPI [KD028FM-1-TP]
2. Touch sensor: 4 wire Resistive touch
3. LED Light bar to display status
4. Processor: CC3200 from Texas Instruments with integrated ARM
Cortex M4 processor
5. SRAM 256KB
6. Permanent storage: External Flash 16MB
7. Power Supply Voltages: 5V provide by USB cable.
8. Power Consumption: 0.3A, 1.5W.
9. WiFi 802.11 b/g/n single band, 2.4GHz [CC3200]
10.RFID HID Prox: 125KHz
Mifare, iClass and Desfire: 13.56MHz
11.Operational temperature +15°C to +35°C
12.Storage temperature 0°C to +70°C
Desk V2 Screen Operational Description
Equipments and software preparation:
1. Desk V2 Screen Programming cable..
2. A USB port to provide 5V power to Desk V2 Screen.
3. A PC with Windows 7 Profectional or later.
4. CCS UniFlash v3.4.0 software for firmware installation. It can be
downloaded for free from internet. Once you have downloaded it
from website, install the UniFlash v3.4.0 on you PC.
5. Condeco Desk V2 Screen firmware.
Desk V2 Screen Firmware Installation:
1. Connect the Desk V2 Programming cable to your PC.
2. Connect the Desk V2 screen’s power lead to your PC’s USB port.
3. Double click the CCS UniFlash icon on your Desktop to start it.
4. Click File on the UniFlash Manu bar and select Open
Configuration.
5. Select and open condeco_prod.usf in C:\ti\uniflash_3.4\condeco\
6. The COM Port number should be the port the USB Programming
Cable connected. It can be find in computer’s Device Manager.
7. Make sure following boxes have been
Checked.
8. Click Format button to format the desk screen’s memory. Choose
the size of the memory as 1Mb.
9. After the memory has been formatted, click the Service Pack
Programming button to update the Service Pack.
•If it’s your first time run the Service Pack Programming, it
will shows a message asking you to download the Service
Pack from the link. Once you have downloaded, install it
into the C:\ti\ folder. After Service Pack has been install,
click Service Pack Programming button and indicate the
path of the pack to program it.
10.After update the Service Pack, click the Program button to load
the Condeco firmware onto the V2 Desk Screen.
11.Once Operation Program returned appears, the programming has
completed.
12.Power off the Desk V2 screen by unplug the power lead from the
USB port.
13.Disconnect the programming cable.
14.Put the back plate on.
15.Finish.
Instruction for Screen Configuration
Desk V2 Screen Configuration:
1. Open the config.ini file in C:\ti\uniflash_3.4\condeco\
2. To Config the Desk ID:
Key in the Desk ID at “resourceid=”, then save the file.
Save the change.
3. To Config http/ https:
In the config.ini file,
“usehttps=0” for http. Set to port 80.
“usehttps=1” for https. Set to port 443.
Save the change.
4. To set or change the URL:
Key in the URL at: “deskservicehost=” and at
“screenservicehost=”
Save the change.
5. To set the secreen rotate position:
1) Set the rotation at 0 °, for install the Desk V2 screen on
the desk.
In the config.ini file, set “rotation=0”
Save the change.
