Comfort Zone CZ2022O User manual

Model No.

CZ2022O – Oak Finish CZ2022W – Walnut Finish

CZ2022C – Cherry Finish CZ2022B – Black Finish

QUARTZ INFRARED HEATER

OWNER’S MANUAL

PLEASE SAVE THESE INSTRUCTIONS

WARNING: READ THIS OWNER’S MANUAL CAREFULLY BEFORE USE.

Thank you for choosing the COMFORT ZONE® Infrared Heating System. This owner’s manual

will provide you with valuable information necessary for the proper care and maintenance of

your new product. Please take a few moments to thoroughly read the instructions and familiarize

yourself with all the operational aspects of your new heater.

IMPORTANT INSTRUCTIONS

When using this electric unit, basic safety precautions should always be followed to reduce the

risk of fire, electric shock, and injury to persons, including the following:

1. Read ALL instructions before using this unit.

2. CAUTION: Risk of Electric Shock. DO NOT open or try to repair the heater yourself.

3. This heater may get hot when in use. To avoid burns, DO NOT let bare skin touch hot

surfaces. If provided, use handles when moving this heater.

4. Keep combustible materials, such as furniture, pillows, bedding, paper, clothes, and

curtains at least 3 ft. from the front of the heater and keep them away from the sides, top

and rear. DO NOT place towels or other objects on the heater.

5. Extreme caution is necessary when any heater is used by or near children or the disabled,

or any time the heater is operating.

6. Do not operate this heater unattended or while sleeping.

7. DO NOT operate any heater with a damaged cord or after the heater malfunctions, has

been dropped or damaged in any manner. Return heater to authorized service facility for

examination, electrical or mechanical adjustment, or repair.

8. This heater is not intended for use in bathrooms, laundry areas and similar indoor

locations. NEVER locate heater where it may fall into a bathtub or other water container.

To protect against electrical hazards, DO NOT immerse in water or other liquids.

9. DO NOT touch the control panel or plug with a wet hand.

10. DO NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners, or

similar coverings. Arrange cord away from traffic area and where it will not be tripped

over.

11. DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening as

this may cause an electric shock or fire, or damage the heater.

12. To prevent a possible fire, DO NOT block the air intakes or exhaust in any manner. DO

NOT use on soft surfaces, like a bed, where openings may become blocked.

13. A heater has hot and arcing or sparking parts inside. DO NOT use in areas where

gasoline, paint, explosive and/or flammable liquids are used or stored. Keep unit away

from heated surfaces and open flames.

14. Always plug heaters directly into a wall outlet/receptacle. Never use with an extension

cord or relocatable power tap (outlet/power strip).

15. To avoid fire or shock hazard, plug the unit directly into a 120V AC electrical outlet.

16. To disconnect heater, turn controls to OFF, then remove plug from outlet. Pull firmly on

the plug, DO NOT unplug by pulling on the cord.

17. Always unplug the unit before moving or cleaning, or whenever the heater is not in use.

18. Use only for intended household use as described in this manual. Any other use not

recommended by the manufacturer may cause fire, electric shock, or injury to persons.

The use of attachments not recommended or sold by unauthorized dealers may cause

hazards.

19. Always use on a dry, level surface. Use on floor only.

20. DO NOT use outdoors.

21. WARNING: To reduce the risk of fire or electric shock, DO NOT use this unit with any

solid-state speed control device.

22. DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit.

Doing so will void your warranty. The inside of the unit contains no user serviceable

parts. Qualified personnel should perform all servicing only.

23. Connect to properly grounded outlets only.

24. PET OWNERS NOTE: The health of birds and some small pets are extremely sensitive

to the fumes given off during the initial use of many appliances. Although these fumes

are not harmful to humans, it is recommended that this heater not be used around birds

and small pets during its initial use until the manufacturing corrosion coatings burn off.

25. Save these instructions.

SPECIFICATIONS

Voltage Rating

120 V (60Hz)

Power Consumption

1500W, 12.5A

Unit Size

13.1 in. (W) x 16.4 in. (D) x 17.8 in. (H)

Unit Weight

31.75 lbs

SAFETY FEATURES

Tip-Over Safety Feature

This heater is equipped with a tip-over safety feature. Once the heater is tipped over, an internal

switch will automatically shut the heater off. Once the heater is restored an upright position, the

heater will reset. To continue operation, turn on the heater using the supplied remote control or

the control panel on the heater.

Overheat Safety Feature

This heater is equipped with a overheat safety feature. When the heaters internal components

reach a certain temperature that could cause overheat and possible fire, the heater will

automatically shut off. To reset, turn heater off and switch master power switch on the rear of

the unit to off position. Unplug the heater and let it cool down for around 20 minutes. Plug the

heater back into the wall outlet and turn master switch and on/off switch to on.

WARNING: This heater has a voltage rating

of 120 volts. The cord has a plug as shown in

(A). An adapter as shown in (C) is available for

connecting three-blade grounding-type plugs to

two-slot receptacles (B). The grounding lug

extending from the adapter must be connected

to a permanent ground such as a properly

grounded outlet box. The adapter should not be

used if a three-slot grounded receptacle is

available.

DO NOT DEFEAT THE SAFETY PURPOSE

OF THE GROUNDED PLUG.



WARNING: It is normal for the power cord to feel warm to the touch; however, a loose fit

between the outlet and the plug may cause overheating of the plug. If the plug is loose, do not

use this outlet. If the plug is loose, try inserting the plug into a different outlet. Contact a

qualified electrician to inspect the original outlet.

IN THE BOX

·INFRARED HEATING SYSTEM

·REMOTE CONTROL

·REMOTE CONTROL BATTERY

·INSTRUCTION BOOKLET

PRODUCT DIAGRAM

Air Outlet

Control Panel

Wheel

Remote Control

Air Intake

Cord Clamp

Master Power

Switch

Temp. Down

Temp. Up

Mode

Power

Timer

1. Signal-receiving window: for receiving remote control signal.

2. Digital display：indicate set room temperature or time value of the timer.

3. Power indication Light: indicates when the unit is connected to power supply and rear master

power switch is on.

4. ON/OFF switch button: for power-on or off.

5. Energy-saving mode：the light is on when energy-saving mode is set.

6. Mode button：for selecting the running mode.

7. Low power mode indication light: The light is on when low power mode is set.

8. Temp up button: to increase set temperature.

9. High power mode indication light: The light is on when high power mode is set.

10. Temp down button: to reduce set temperature.

11. Timer indication light：the light is on when timer mode is set.

12. Timer button：used for setting the timer and adjust time value for the timer.

13. Fahrenheit indicator light.

14. ℃/℉Button (Button for alternating between Fahrenheit and Celsius).

15. Celsius indicator light.

Control Panel

Temp. Down

Temp. Up

Mode

Power

Timer

PREPARATION

Place the heater on a firm, level surface and plug into a grounded 120V, 60Hz power outlet. and

turn on the master power switch in the rear of the unit. Only operate heater in upright position

with caster wheels attached.

When using remote control, please pull out the battery insulating film as shown below.

PULL

Remote control

Insulating film

Battery cover

Remote Control

Mode button: Used for mode selection

ON/OFF button: Used for power-on or power-off when master

power switch on rear of unit is on

Temp up button: to increase set temperature

Temp down button: to reduce set temperature

Timer button: used for setting timer and adjust time value of the timer

OPERATING INSTRUCTIONS

1. Start and select working mode

With master power switch at the rear of the unit on, turn

the heater on by pressing the ON/OFF button on the

control panel or by pressing the Power button on the

supplied remote control.

Once power is off, heating elements will stop working at first.

Fan will continue working for up to 3 minutes to emit residual

heat inside the unit.

Select a heat setting.

Press the MODE button to toggle between the three heat

settings.

High Mode uses 1500W; Low Mode uses 750W. ECO

mode is an Economic Energy Saving Function. When ECO

mode is chosen, the heater will set the temperature

automatically to 68°F （20℃）under this mode

2. Setting room temperature

Or Or

Adjust the thermostat by pressing the arrows on the control

panel or remote control.

Set temperature indication varies from 59℉to 86℉，or

from 15℃to 30℃. Once you have chosen the desired

temperature, the heater will remain on until the room

temperature increases to the temperature on the digital

display. The heater will cycle on and off to maintain the

desired room temperature.

Press ℃/℉button, then digital display will indicate

Fahrenheit value or Celsius value.

When Fahrenheit indicating light’s on, digital display

indicates Fahrenheit value,

When Celsius indicating light’s on, digital display

indicates Celsius value.

3. Setting timer-power-off

Note: ONLY under power-on mode can you set timer-power-off function.

After starting the unit, press the timer button on the control

panel.

Digital display changes from set temperature to time value

for the timer. Each press of the timer button will increase

the timer length by 1 hour up to 12 hours. To cancel the

timer, cycle through the lengths until the value is “00”

The timer light is on when timer–power-off is set.

4. Setting timer-power-on

Note: ONLY under power-off mode can you set timer-power-on function.

Under power-off mode, press the timer button on the

control panel.

Digital display will indicate the time value for the timer.

Each press of the timer button will increase the timer

length by 1 hour up to 12 hours. To cancel the timer, cycle

through the lengths until the value is “00”

The light is on when timer–power-on is set.

5. Setting electro-lock

Function of electro lock can avoid unwanted use from children. Electro-lock can be set in

both power-on and power-off modes.

And

Press both Temp Up and Temp Down buttons for 3

seconds. Locking is confirmed when a tone is heard. When

locked, control panel and remote control will not function.

And

To unlock the locked control panel, press both Temp Up

and Temp Down buttons for 3 seconds. Unlock is

confirmed when a tone is heard. Control panel and remote

control return to normal functions.

MAINTENANCE

1. Turn off the master power switch in the rear of the unit.

2. Unplug the unit and let it cool completely.

3. To keep the heater clean, the outer shell may be cleaned with a soft, damp cloth. You

may use a mild detergent if necessary. After cleaning, dry the unit with a soft cloth.

CAUTION: DO NOT let liquid enter the heater.

4. DO NOT use alcohol, gasoline, abrasive powders, furniture polish, or rough brushes to

clean the heater. This may cause damage or deterioration to the surface of the heater.

5. DO NOT immerse the heater in water. Unit must be completely dry before use.

6. Air filter needs cleaning after 3 months of use or when it appears dirty. Remove the filter

using the below steps. Wash and clean the filter with water, dry it out completely and re-

assemble. Do not use the heater with a wet filter.

7. If you don’t plan to use the unit for a long time, please take out battery of the remote

control according using the following steps.

PULL

PUSH

Battery cover

Battery

Remote control

Air filter

The unit

Filter bracket

Remove

bracket

screws

with

screwdriver

STORAGE

Store the heater in a cool, dry location when not in use. To prevent dust and dirt build-up, use the

original packaging to repack the unit.

TROUBLESHOOTING

If the heater will not operate, please check the following before seeking repair of service:

1. Check if the power cord is plugged into an electrical outlet, if not, plug in.

2. Check if electricity to the main fuse is working and the outlet has power.

3. Be sure master power switch on the rear of the unit is on.

4. Check if the battery in remote control is good and if the insulating film is pulled out.

NOTE: The heater may not be operating if the thermostat is set lower than the room

temperature. To begin operation, increase the thermostat temperature for a higher heat

setting.

LIMITED WARRANTY

Products manufactured by Comfort Zone® are warranted to the original consumer to be free of

defects in material and workmanship for twelve (12) months from the original date of purchase.

The warranty does not cover products modified outside our factory, damage or failure caused by

acts of God, abuse, misuse, abnormal usage, faulty installation, failure to follow suggested

maintenance procedures enclosed with this product (as defined by Magnuson-Moss Warranty-

Federal Trade Commission lmprovement Act) This unit is guaranteed to the original retail

purchaser against defects in quality or workmanship for a period of one year from the date of

original purchase. If this unit fails because of a manufacturing defect within 30 days of purchase,

return the unit, with your receipt, to the retailer. After 30 days, but within the warranty period, if

the unit was purchased within the continental united States, return it, freight prepaid, to Comfort

Zone®. for repair or replacement. If the unit was purchased outside the continental united States,

return the unit to the place of purchase. This warranty does not cover damage due to accidents,

operation on other than 120 volts, 60 hertz, AC. current, or any other abuse. All implied

warranties, including the warranties of merchantability and of fitness of purpose, if applicable,

are hereby limited in duration to the period of one year from the date of original retail purchase.

Some states do not allow limitations on how long an implied warranty lasts, so the above

limitations may not apply to you. Incidental or consequential damages arising from a breach of

either express or implied warranties are hereby disclaimed and excluded. Some states do not

allow the exclusion of limitation of incidental or consequential damages, so this limitation or

exclusion may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights, which vary

from state to state. No informal dispute settlement mechanisms are available. This limited

warranty is given in lieu of all other warranties.

Manufactured for:

Comfort Zone®

324A Half Acre Rd.

Cranbury, NJ 08512 USA

800-221-6895

www.comfortzoneheaters.net

This manual suits for next models

Table of contents

Other Comfort Zone Heater manuals

Comfort Zone

Comfort Zone CZPH25RSLS3 Series User manual

Comfort Zone

Comfort Zone CZ499R Series User manual

Comfort Zone

Comfort Zone CZ488 User manual

Comfort Zone

Comfort Zone CZHTV9 Series User manual

Comfort Zone

Comfort Zone CZ260ER Series User manual

Comfort Zone

Comfort Zone CZQTV007E Series User manual

Comfort Zone

Comfort Zone CZ2011O User manual

Comfort Zone

Comfort Zone CZ465E Series User manual

Comfort Zone

Comfort Zone CZ2011P User manual

Comfort Zone

Comfort Zone CZ523 Series User manual

Comfort Zone

Comfort Zone CZ449E Series User manual

Comfort Zone

Comfort Zone CZ410 Series User manual

Comfort Zone

Comfort Zone CZ470 Series User manual

Comfort Zone

Comfort Zone CZ2032O User manual

Comfort Zone

Comfort Zone CZ9010 Series User manual

Comfort Zone

Comfort Zone CZ220 Series User manual

Comfort Zone

Comfort Zone CZ485 Series User manual

Comfort Zone

Comfort Zone CZ466BK User manual

Comfort Zone

Comfort Zone CZ277 Series User manual

Comfort Zone

Comfort Zone CZ457E Series User manual

Comfort Zone

Comfort Zone CZ2011P User manual

Comfort Zone

Comfort Zone CZ275 Series User manual

Comfort Zone

Comfort Zone CZ8008N Series User manual

Comfort Zone

Comfort Zone CZQTV008E Series User manual

Popular Heater manuals by other brands

oventrop

oventrop Regucor Series quick start guide

Blaze King

Blaze King CLARITY CL2118.IPI.1 Operation & installation manual

ELMEKO

ELMEKO ML 150 Installation and operating manual

BN Thermic

BN Thermic 830T instructions

KING

KING K Series Installation, operation & maintenance instructions

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Installation instructions and owner's manual

Well Straler

Well Straler RC-16B user guide

EUROM

EUROM 333299 instruction manual

Heylo

Heylo K 170 operating instructions

Eterna

Eterna TR70W installation instructions

Clarke

Clarke GRH15 Operation & maintenance instructions

IRSAP

IRSAP The Radiator Company Ovali Fitting instructions

Empire Heating Systems

Empire Heating Systems WCC65 Installation and owner's instructions

Wetekom

Wetekom 92 86 43 Original instructions

Desa

Desa SPC170-F owner's manual

Watlow

Watlow Watrod Electric Tubular Heaters Specifications

Haverland

Haverland ECO-DRY GPS Series Instruction & installation manual

Stelpro

Stelpro ASILVC2060 Series user guide