XHS1-UE
ZigBee Home Automation 1.2
Wireless Digital Pet Resistant PIR Detector
XFINITY HOME
Installation Instructions
1. INTRODUCTION
The XHS1-UE pet resistant detector is a
microprocessor-controlled wireless digital PIR
detector supported by ZigBee Home Automation
1.2. The detector’s features are as follows:
A. Red LED
B. Green LED
C. Tamper Switch
Figure 1 – XHS1-UE
2. SPECIFICATIONS
Detector Type: Two - Dual element low-noise pyroelectric sensor
Optical Data: 18 parabolic mirrors for long range
18 parabolic mirrors for close range
Max. Coverage: 15 x 15 m, (49.2 x 49.2 ft) / 90°
Pet Immunity: Up to 38 kg (85 lb)
ELECTRICAL
Internal Batteries: Two 3V Lithium batteries, type CR-123A. For UL installations, use Panasonic only
Nominal Battery Capacity: 1400 mAh per battery
Battery Life (with LED on): Typically over 5 years
Note: Inability to connect with wireless network, or wireless link quality resulting in intermittent connection may
significantly reduce the expected battery life.
Battery Power Test: Performed immediately upon battery insertion and during each transmission to the panel
FUNCTIONAL
Alarm Period: 3 seconds
Visual Indications: Red LED lights for about 3 seconds upon transmission of alarm & tamper messages and upon motion
detection in the walk test mode only (walk test mode available for approx. 15 minutes). Red LED flashes during
the power-up stabilization period, or after restoring (pressing) the tamper switch (power-up stabilization period
is approx. 1 minutes). LED does not light upon transmissions of supervision messages or alarm detection after
termination of walk test mode.
Rearm Timer: Rearms the detector 2 minutes after the last alarm. Timer disabled in the walk test mode.
WIRELESS
Supported Network: ZigBee H.A 1.2
Frequency: 2.405 – 2.480 Ghz as per IEEE 802.15.4
Tamper Alert: Reported when a tamper event occurs and in any subsequent message, until the tamper switch is restored
MOUNTING
Height: 1.8-2.4 m (6 - 8 ft). For pet rejection, the optimal height is 2.1 m (7 ft)
Installation Options: Surface or corner
ENVIRONMENTAL
Operating Temperatures -10˚ C to 55˚ C (14˚ F to 131˚ F)
Storage Temperatures -20˚ C to 65˚ C (-4˚ F to 149˚ F)
COMPLIANCE WITH STANDARDS
USA CFR 47 part 15,
ANSI/UL 639
PHYSICAL
Size (H x W x D) 83 x 61 x 42 mm (3.27 x 2.4 x 1.66”)
Weight (with battery) 90 g (3.17 oz)
Color White
4. TROUBLESHOOTING
If you encounter one of the following problems with the XHS1-UE, use the following solutions to
resolve the problem:
Problem Solution
Attempt to pair the sensor is unsuccessful. Reset the detector to default mode and then set to
pairing mode (see section 3.5).
The sensor and the Touchscreen (control panel) Perform the signal strength testing procedure
do not communicate. described in the control panel installation manual.
Make sure that the signal is sufficient. If necessary,
replace the sensor’s battery.
The sensor sends a Low Battery indication. To ensure continuous proper operation, replace the
battery within two weeks of the first Low Battery
indication.
Panel does not arm because of an unrecognized Consult with your installer or system provider before
sensor malfunction. you disable a zone. Disable the sensor zone (see
the control panel user manual). Note that disabling
a sensor zone lowers the overall security level of
your system.
5. SPECIAL COMMENTS
Even the most sophisticated detectors can sometimes be defeated or may fail to warn due to: DC power failure
/ improper connection, malicious masking of the lens, tampering with the optical system, decreased sensitivity
in ambient temperatures close to that of the human body and unexpected failure of a component part. The
above list includes the most common reasons for failure to detect intrusion, but is by no means comprehensive.
It is therefore recommended that the detector and the entire alarm system be checked weekly, to ensure
proper performance. An alarm system should not be regarded as a substitute for insurance. Home and property
owners or renters should be prudent enough to continue insuring their lives and property, even though they are
protected by an alarm system.
6. COMPLIANCE WITH STANDARDS
FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
• Reorientorrelocatethereceivingantenna.
• Increasetheseparationbetweentheequipmentandreceiver.
• Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiveris
connected.
• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
You are cautioned that changes or modifications not expressly approved by the party responsible for
compliance could void your authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
ETL Statement: This device conforms to ANSI/UL STD 639
Installation shall be done in accordance with the Standard for Installation
and Classification of Burglar and Holdup Alarm Systems, UL 681.
4008840
4 MUG-XHS1-UE-B Date: 11/01/2016 MUG-XHS1-UE-B Date: 11/01/2016 1
XHS1-UE_ UM_B.indd 1 11/4/16 12:37 PM
