Coemar CF 1200 Spot User manual

CF 1200 Spot

serial number

date of purchase

retailer

address

suburb

capital city

state

tel./fax/

Please note in the space provided above the relative service information of the model and the retailer from

whom you purchased your

CF 1200 Spot

: This information will assist us in providing spare parts, repairs or in

answering any technical enquiries with the utmost speed and accuracy.

WARNING: the security of the fixture is granted only if these instructions are strictly followed; therefore it is

absolutely necessary to keep this manual.

514 mm

692 mm

750 mm

204 mm

306 mm

592 mm 546 mm

Index

1. Packaging

2.Transporting

3.Important safety information

4. Lamp: installation and replacement

5. Operating voltage and frequency

6. Mounting the unit

7. Mains connection

8. Signal connection

9.Powering up

10.DMX addressing

11.Display panel functions

12.Control channel functions from a DMX 512 controller

13.Aligning the lamp in the optical system

14.Interchanging dichroic colours on the colour wheel

15.Automatic internal functions

16.Maintenance

17.Electronic alignment of the motors

18.Spare parts

Authorised coemar service centres

Congratulations on having purchased a new coemar product; you have assured yourself of a fixture of the highest quality,

both in the components used and in the technology. We renew our request to you to complete the service information on the

preceding page, to expedite any request for information, or for service (in case of problems encountered either during, or sub-

sequent to, installation). This information will assist in prompt and accurate advice from your authorised coemar service centre.

1. Packaging Following the instructions contained in this manual will ensure the maximum effi-

ciency of this product for years to come.

Open the packing and ensure that no part of the equipment has suffered damage in

transit. In the case of damage to the equipment, contact the carrier immediately by

telephone or fax, following this with formal notification in writing.

packing list

Ensure that the packaging contains:

1 CF 1200 Spot

1 instruction manual

2. Trasporting The CF 1200 Spot should always be transported in its original packaging or in a

coemar approved flight case.

In order to manufacture a suitable flight case, we recommend the following simple

procedures be followed which will stop the articulated movement of the CF 1200

Spot during transportation.

Below are illustrated the 2 diverse methods of padding which coemar recom-

mends.

A) Padding around the entire projector, including the base, with suitable padding

materials.

B) Fixing the base to a rigid support, with padding surrounding the articulated head.

Polietilene

espanso/

Foam

Pomoli di

bloccaggio/

Knobs

Polietilene

espanso/

Foam

3. Important safety Fire prevention

information 1. CF 1200 Spot uses a Philips MSR 1200 SA lamp; the use of any alternative lamp

is not recommended and will null and void the fixture’s warranty.

2. Never locate the fixture on any flammable surface

3. Minimum distance from flammable materials: 0.5 m.

4. Minimum distance from the closest illuminable surface: 2 m.

5. Replace any blown or damaged fuses only with those of identical values. Refer to

the schematic diagram if there is any doubt.

6. Connect the projector to mains power via a thermal magenetic circuit breaker.

Prevention of electric shock:

1. High voltage is present in the internals of the unit. Isolate the projector from

mains supply prior to performing any function which involves touching the inter-

nal of the unit, including lamp replacement.

2. For mains connection, adhere strictly to the guidelines outlined in section 7 of this

manual.

3. The level of technology inherent in the CF 1200 Spot requires the use of spe-

cialised personnel for all service applications; refer all work to your authorised

coemar service centre.

4. A good earth connection is essential for proper functioning of the projector.

The projector should never be operated without proper earth connection.

5. The fixture should never be located in an exposed position, or in areas of extreme

humidity. A steady supply of circulating air is essential.

Protection against ultraviolet radiation:

1. Never turn on the lamp if any of the lenses, filters, or the carbon fibre housing is

damaged; their respective functions will only occur efficiently if they are in perfect

working order.

Never look directly into the lamp when it is operating.

Safety:

1. The projector should always be installed with bolts, clamps, and other fixings

which are suitably rated to support the weight of the unit.

2. Always use a secondary safety chain of a suitable rating to sustain the weight of

the unit in case of the failure of the primary fixing point.

3. The external surface of the unit, at various points, may exceed 150°C. Never

handle the unit until at least 10 minutes after the lamp has been turned off.

4. Always replace the lamp if any physical damage is evident.

5. Never install the fixture in an enclosed area lacking sufficient air flow; the ambient

temperature should not exceed 35°C.

6. The hot lamp may explode, always wait at least 10 minutes after it has been tur-

ned off prior to attempting to replace or handle the lamp.

Always wear suitable hand protection when handling the lamp.

4. Lamp: Installation CF 1200 Spot utilises a 1200 W Philips MSR 1200 SA lamp.

and replacement with a GY 22.lamp base

The lamp is available from your authorised coemar sales agents:

coemar cod. 105090/1

wattage 1200 w

luminous flux 96.000 lm

colour temperature 6500° K

base GY 22

approximate life 500 hours

The fixture’s internal temperature can reach 250° C after 5 minutes, with a maximum

peak of 350° C; ensure that the bulb is cold before attempting removal. The fixture

should be allowed to stand and cool for 10 minutes prior to its removal.

MSR/SA lamps are part of the mercury vapour family of discharge lamps and must be

handled with great care. The lamp operates at high pressure, and the slight risk of

explosion of the lamp exists if operated over its recommended life of 500 hours.

We recommend, therefore, that the lamp be replaced within the manufacturer’s spe-

cified lamp life.

lamp installation

1) With the use of a 3mm Allen Key, loosen the two bolts (A) which fix the lamp

assembly to the body of the projector.

2) Remove the lamp assembly (B).

3) Locate the lampholder (C)

Attention

Disconnect mains power prior to inspecting the unit internally.

4) Insert the lamp (D). The lamp used is manufactured from quartz glass and should

be handled with care; always adhere to the instructions supplied in the lamp’s

packaging. Do not touch the glass directly, the the tissue provided in the lamp

packaging. The GY 22 lampholder is assymetrical in construction. One lamp pin is

larger than the other; therefore make sure that the lamp’s pins are correctly ali-

gned in the lampbase. If you encounter difficulty during this operation, DO NO

USE UNDUE FORCE. Re-read the instructions and repeat the procedure.

5) Replace the lamp assembly (B) in its original position and replace the two bolts

(A) which were previously removed.

Attention: we recommend that the lamp be realigned in the optical train of the

unit to avoid overheating the dichroic filters within the unit; refer to section 13 for

instructions about this procedure.

5. Operating voltage coemar factory presets (barring specific requests), a voltage of 230v to 240v

and frequency selectable via a switch on the base of the CF 1200 Spot.

Remember to set the selector (230 or 240V) to the selection which most closely matches

the operating voltage at your venue.

If your operating voltage is 208V, this may be selected internally by shifting the cable

labelled 21 (connected to the 240V position of the switch) or cable 22 (connected to

the 230V switch), thereby, however, eliminating the ability to select either 230V or

240V.

Incorrect voltage selection will detrimentally affect the operation of

the projector. Under no circumstances should cable 23 be moved.

CF 1200 Spot is fitted with an electronic ballast which automatically adjusts the

output voltage to the projector when the input voltage is in the range of 180 to

260V; it is therefore not necessary to make any modifications when moving to

venues with power supplies in this range.

115V

208V

230V

240V

Bianco/White

Nero/black 230V

Rosso/red 115 V

Blu/blue 240V

Giallo/yellow 208 V

oemar set

main at:

115V

208V

230V

240V

230V

coemar set

main at:

115V

208V

230V

240V

6. Mounting the unit mounting

CF 1200 Spot may be floor or ceiling mounted.

The structure from which the unit is hung should be of sufficient rating to hold the

weight of the unit, as should any clamps used to hang the unit.

The structure should also be sufficiently rigid so as not to move or shake whilst the

CF 1200 Spot moves during its operation.

The mouting holes in the base of the unit allow it to be mounted at various angles to

the mounting truss, and to trusses of various dimensions.

The following is a diagram of the base of the CF 1200 Spot.

165mm

455mm

n°6 asole 72x12 mm r= 6 mm

In order to obtain maximum efficiency of movement, the unit should be mounted

with the ” Front” label facing the main illumination point.

protection against liquids

The projector contains electric and electronic components that must not come into

contact with water, oil, or any other liquid.

moviment

The projector has a movement of 370° in the base and 270° in the yoke; DO NOT

place any obstructions in the path of the projector’s movements.

safety chain

The use of a safety chain (cod. 069) - fixed to the CF 1200 Spot and to the primary

suspension point, is highly recommended to protect against accidental failure,

however unlikely, of the primary suspension point.

If using an after-market safety chain, not manufactured by coemar, ensure that it is

of sufficient strength to hold the weight of this fixture.

risk of fire

Each fixture produces heat and must be installed in a well-ventilated position. The

minimum recommended distance from flammable material is: 0.5m. Minimum

distance from the object being illuminated is: 2m.

7. Mains connection cabling

The mains cable provided is thermally resistant, complying to the most recent inter-

national standards. It meets or exceeds the VDE and IEC norms, IEC 331, IEC 332

3C, CEI 20 35.

NB: In the case of cable replacement, similar cable, with comparable thermal resi-

stant qualities must be used exclusivelly (cable 3x1,5 ø external 10 mm, rated

300/500V, tested to 2KV, operating temperature -40° +180°, coemar cod.

CV5309).

mains connection

CF 1200 Spot can operate at voltages from 208V-230V-240V at 50 or 60Hz (ope-

rating voltage and frequency can be selected as described in section 5 of this

manual).

Prior to connecting the unit to your mains supply, ensure that the model in your pos-

session correctly matches the mains supply available to you.

For connection purposes, ensure your plug is of a suitable rating: 9,5 amps.

Locate the mains cable which exits the base of the unit and connect as shown

below:

marrone - brown

blu - blue

giallo/verde - yellow/green

marrone - brown

blu - blue

giallo/verde - yellow/green

massa

ground

neutro

neutral

fase

phase

alimentazione

main

marrone - brown

blu - blue

giallo/verde - yellow/green

Table of contents

Other Coemar Lighting Equipment manuals

Coemar

Coemar Par lite ACL User manual

Coemar

Coemar MiniLEDko Spot User manual

Coemar

Coemar Reflection FullSpectrum User manual

Coemar

Coemar ProWash 575 LX User manual

Coemar

Coemar Stage Lite Led sc User manual

Coemar

Coemar Risalto Led + User manual

Coemar

Coemar CF ZOOM AL User manual

Coemar

Coemar LEDko DIM T User manual

Coemar

Coemar i spot S User manual

Coemar

Coemar Otello 6 HD + User manual

Coemar

Coemar Reflection LEDko User manual

Coemar

Coemar LineaLED Flexible User manual

Coemar

Coemar Reflection LedkoP User manual

Coemar

Coemar LEDko EXT User manual

Coemar

Coemar pilota 1200 User manual

Coemar

Coemar CF 1200 Hard Edge User manual

Coemar

Coemar ProSpot LX User manual

Coemar

Coemar par lite LED IP User manual

Coemar

Coemar Reflection LEDko FullSpectrum 6 User manual

Coemar

Coemar ProSpot 150 LX User manual

Coemar

Coemar ColourCyc 250LX User manual

Coemar

Coemar Infinity Spot S User manual

Coemar

Coemar LEDko FullSpectrum 2 + RGBL User manual

Coemar

Coemar Mini ReLite Led User manual

Popular Lighting Equipment manuals by other brands

Brizo

Brizo 8SP-MU-4 manual

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 installation instructions

IKEA

IKEA BJÖRKSPIREA manual

Laserworld

Laserworld Evolution Series ES-400RGB manual

Alien

Alien RG STAR user manual

EuroLite

EuroLite LED B-40 user manual

Qazqa

Qazqa Suplux SL 3 Black 103062 instruction manual

Commercial Electric

Commercial Electric 54568141 Use and care guide

CREE LIGHTING

CREE LIGHTING 304 Series installation instructions

Goobay

Goobay 49867 user manual

ECOMAN ITALIA

ECOMAN ITALIA LED T8 instruction manual

Alkalite

Alkalite Krypton KT-81 user manual

Clas Ohlson

Clas Ohlson GU10 manual

DTS

DTS DELTA 10 F user manual

ring

ring Solar Steplight manual

One Stop Gardens

One Stop Gardens 57696 Owner's manual & safety instructions

Chauvet DJ

Chauvet DJ COREpar UV120 ILS user manual

SIREM

SIREM Swimeo A2 instructions