Cocraft HC85 User manual
ENGLISHSVENSKANORSKSUOMIDEUTSCH
Important!
Read the entire instruction manual
carefully and make sure that you fully
understand it before you use the
equipment. Keep the manual for future
reference.
Viktig information:
Läs hela bruksanvisningen noggrant och
försäkra dig om att du har förstått den
innan du använder utrustningen. Spara
bruksanvisningen för framtida bruk.
Viktig informasjon:
Les disse anvisningene nøye og forsikre
deg om at du forstår dem, før du tar
produktet i bruk. Ta vare på anvisningene
for seinere bruk.
Tärkeää tietoa:
Lue nämä ohjeet huolellisesti ja varmista
että olet ymmärtänyt ne, ennen kuin
alat käyttää laitetta. Säilytä ohjeet
myöhempää tarvetta varten.
Wichtiger Hinweis:
Vor Inbetriebnahme die komplette
Bedienungsanleitung sorgfältig
durchlesen und aufbewahren.
HC85
FOR 1/4”, 3/8”AND .325” CHAINSAW CHAINS
85 W
18-3057 ∙30-9678
CHAINSAW SHARPENER
KEDJESLIPMASKIN
KJEDESLIPEMASKIN
TERÄKETJUN HIOMAKONE
KETTENSCHLEIFMASCHINE
Ver. 20161020
Original instructions
Bruksanvisning i original
Originalbruksanvisning
Alkuperäinen käyttöohje
Original Bedienungsanleitung
Art.no Model
18-3057 2002-UK
30-9678 2002
ENGLISH
3
Chainsaw Sharpener
Art.no 18-3057 Model 2002-UK
30-9678 2002
Please read theentire instruction manual before using and save for future use. We apologise for
any text or photo errors and any changes of technical data. If you have any questions concerning
technical problems please contact our Customer Service Department (see address on reverse.)
Safety
General Safety Instructions
Warning:
When using this tool all basic safety precautions must be followed to avoid therisk of fire,
electrocution and personal injury. Read these instructions carefully before using theproduct
and keep them for future reference.
• Keep theworking area clean. Cluttered areas and benches invite accidents.
• Consider your work area environment. Do not expose thetool to rain. Do not use thetool
in moist or wet areas. Keep theworking area well lit. Never operate thetool near flammable
liquid or gas.
• Avoid electric shocks. Avoid body contact with earthed objects, such as pipes, radiators,
ovens or refrigerators.
• Keep other people at asafe distance. Do not allow anyone not involved in thework process
to touch thetool or its electric cable, especially children. Keep all bystanders at adistance.
• Store thetool in asafe place. When your tools are not in use, keep them in alocked, dry
area, away from children.
• Do not overload thetool. Thecorrect feed rate makes thetool work better and safer.
• Use thecorrect tool for thejob. Do not try to use small tools to perform jobs requiring more
powerful tools. Do not use atool for apurpose for which it was not designed, e.g. using
acircular saw for lopping branches off trees.
• Wear suitable clothing. Do not wear loose-fitting clothing or jewellery, that could get caught in
moving parts. Non-slip shoes are recommended for outdoor work. Wear ahairnet or similar if
you have long hair.
• Always use safetywear. Wear safety glasses. Use aface mask or dust filter when working in
dusty environments.
• Use dust extractors. If thetool is equipped with or connected to adust extractor/collector,
make sure that it is turned on and used correctly.
• Do not abuse thelead. Do not jerk thelead, grip theplug itself when disconnecting thepower.
Make sure that themains lead does not come into contact with heat, oil, or sharp edges.
• Firmly secure theworkpiece. If possible use vices or clamps to hold theworkpiece in place.
This is much safer than holding theworkpiece in one hand.
• Do not overreach. Make sure that you stand steady and balanced all times.
ENGLISH
4
• Look after you tools. Make sure that they are clean and that theedges are sharp for
maximum effect and best results. Follow themanuals recommendations regarding lubrication
and replacement of accessories. Inspect themains lead regularly. If it is damaged it should
be replaced by aqualified service technician. Inspect all leads and cables regularly to check
for any damage. Make sure that themachine’s/tool’s handles and controls are clean, dry and
free from oil and grease.
• Turn thepower off. Pull out theplug and push in theemergency stop button before servicing
or changing any blades, drill bits, cutters or sanding discs.
• Remove all spanners and repair tools. Make ahabit of checking to make sure that
themachine is free of all spanners and tools before turning thepower on.
• Avoid accidental starting. Do not walk around with your finger on thetrigger of apower tool
if it is plugged in. Make sure that theon/off switch is set to OFF before plugging in any power
tool.
• Use thecorrect extension leads. If you use extension leads outdoors, only use those
designed for outdoor use. Only use extension leads with thick enough diameter core wires
and roll out thewhole lead.
• Use common sense and be careful. Think before carrying out any task, so that it is carried
out safely. Never operate machines/power tools when you are tired or under theinfluence
of medicine.
• Check thefollowing before turning thetool on:
- That all guards and other parts are whole and in working order.
- That moving parts are free and correctly aligned.
- That no moving parts can get caught.
- That no defects are apparent.
Other factors that can influence work execution. Asafety guard or any other part that is
damaged should be repaired by atradesman or replaced. Damaged power leads and
switches must always be replaced by atradesman. Never operate atool if you cannot stop
or start thetool comfortably.
• Use only recommended accessories. Theuse of non-recommended accessories can cause
accidents and personal injury.
• Should only be repaired by aqualified technician. Thetool conforms to current safety
requirements. Repairs to thetool should only be carried out by atradesman using original
spares; otherwise thetool could cause accidents and personal injury.
Specic Safety Rules
• Always use safety glasses.
• Never use damaged grinding discs.
• Never use thechainsaw sharpener unless theguard is attached and undamaged.
• Only use grindings discs recommended by themanufacturer and that are rated at thesame
or higher speed than themaximum rated speed of themachine.
• Read themanufacturer’s instructions accompanying thegrinding disc.
ENGLISH
5
Before Starting the Machine
• Make sure that thepower switch is set on 0before connecting themachine to awall socket.
Only connect themachine to anearthed wall socket.
• Make sure that thegrinding wheel is well centred and undamaged and that theguard is
attached and intact before use.
• Use only grinding wheels with thecorrect diameter and which are approved for thespeed of
themachine.
• Protect thegrinding wheel from moisture and blows.
• Make sure that thegrinding wheel can rotate freely before starting themachine.
• Always pull theplug out of thewall socket before servicing and adjusting thechainsaw sharpener.
Whilst Operating the Machine
• Pull out theplug if themachine is left unattended.
• Stand steady and hold themachine firmly in both hands.
• Keep aneye on theelectric cable whilst using themachine so that it is not damaged by
thegrinding wheel or thesharp edges of thechain.
• Grip thechain securely in thevice before starting to grind.
• Do not use themachine around flammable materials. Thegrinding process causes sparks
which can ignite fires or explosions.
• Position thesharpener below eye level in awell-lit place.
• Wait until thegrinding wheel arm is completely raised before feeding thechain forward to
thenext link.
• Bear in mind that thelinks of thechain are sharp, keep fingers well clear when feeding
thechain forward to thenext link.
• This sharpener is only intended for sharpening chainsaw chains, thegrinding or cutting of items
other than these chains is not permitted. Do not use grinding tools other than grinding wheels.
Turn the machine off immediately if…
• Themachine starts to behave strangely, e.g. emits smoke, sparks, strange noises or starts
vibrating.
• Themachine’s power switch or electric cable is damaged.
Product safety symbols and their meaning
Read theentire instruction manual before using theproduct.
Always use safety glasses. Always use ear protection.
ENGLISH
6
6
1
9
4
4
7
7
2
10
5
8
3
Product Description
1. Power Switch Off (0) / On (I)
2. Vice Locking Knob
3. Grinding Wheel Guard
4. Grinding Wheel Arm
5. Grinding Wheel
6. Depth Stop with Lock Nut
7. Length Adjustment Screw
with Lock Nut
8. Chain Stop
9. Chain Vice
10. Chain Locking Lever
Not included
ENGLISH
7
11 5
Installation, mounting
1. Position thesharpener on theworkbench in such away that thetwo feet on thebottom rest
against thelip of theworkbench and thevice locking knob (2) is accessible. Bear in mind that
work area needs to be well-lit for adjusting and using thesharpener.
2. Bolt thechainsaw sharpener to theworkbench using thetwo holes in thebase.
Fitting and replacing the grinding wheel
1. Raise thegrinding wheel arm (4) to maximum elevation.
2. Undo thetwo screws holding thegrinding wheel guard (3) in place and remove it,
keep thescrews safe.
3. Unscrew theflange nut (11) holding thegrinding wheel (5) in place and remove both thelock
nut and grinding wheel. (turn thelock nut anticlockwise to undo it).
4. Insert anew grinding wheel onto thespindle making sure that it is centred and that
theflanges are clean and flat. Tighten theflange nut (11) by hand, if theflanges are tightened
too much thegrinding wheel could become damaged, which could lead to theoperator
being seriously injured if thewheel shatters during use. Use only recommended grinding
wheels according to thespecifications. Make sure that theflange nut (11) is theright way
round; thecupped side should be facing thegrinding wheel.
5. Screw thegrinding wheel guard (3) back on.
6. Always test newly attached wheels by starting
themotor and letting thewheel spin for
aminute or two before starting work.
Whilst testing thewheel you should
remain at asafe distance and not
allow anyone else to come close in
case thedisc shatters.
If you notice that thewheel
vibrates when turned on
or during operation,
themachine should be
stopped immediately
and thewheel
should be inspected.
Warning:
Never try to stop thegrinding wheel with your hand even if you are wearing safety gloves.
Contact with agrinding wheel spinning at high speed can cause burns and scrapes.
ENGLISH
8
7.
10.
8.
7
8
10
43
6
7
2
Adjustment
Warning:
All adjustments should be made when themachine is turned off and unplugged.
1. Check which type of chain you have, set thecorrect filing angle (most chains have afiling
angle of 30° or 35°), tighten thelocking knob (2) on thebottom.
2. Lay thechain in thevice and lower thechain stop (8) behind thelink to be sharpened first.
3. Carefully lower thegrinding wheel arm (4) (all adjustments should be made with themotor
turned off). Thechain stop (8) should rest against theback of thelink to be sharpened, adjust
thechain stop (8) using thelength adjuster screw (7) so that thegrinding wheel will come into
contact with thecutting edge of thelink when it is lowered.
4. Fix thelength adjuster screw (7) by tightening thelock nut.
5. Tighten thevice lock knob to hold thechain in place, if it gets caught on your arm it can be
adjusted as follows: Undo thechain locking lever and move it to thedesired position.
6. Carefully lower thegrinding wheel arm (4) again and set thedesired cutting depth using
thedepth stop (6), tighten thelock nut.
7. Lower thegrinding wheel arm (4) and test if thesetting is correct before starting themotor.
8. Thesharpener is now set up.
ENGLISH
9
min 3 mm (1/8″)
Use
Warning:
Never try to stop thegrinding wheel with your hand even if you are wearing safety gloves.
Contact with agrinding wheel spinning at high speed can cause burns and scrapes.
1. Clean thechain thoroughly before sharpening, do not use aflammable solvent.
Allow thechain to dry before starting to sharpen it.
2. Lay thechain in thevice (9), lower thechain stop (8) against theback of thelink and stretch
thechain backwards toward thechain stop, tighten thevice locking lever (10) so that
thechain is locked in place.
3. Lower thegrinding wheel arm (4) and test if thesetting is correct before starting themotor.
Remember to put your safety glasses on before starting themotor!
4. Push thegreen start button to start themotor and let it come up to speed.
5. Carefully lower thegrinding wheel arm and test it on one of thelinks, carefully raise thearm
again, check theresults, turn themotor off and adjust if necessary. If thesettings are correct
you can continue sharpening. Bear in mind that best results are achieved if thecontact
between thegrinding wheel and thechain link occurs gradually and gently, do not grind
thesame link for too long.
6. Fully elevate thegrinding wheel arm, undo thevice locking lever (10) and move thechain
forwards to thenext link (which is facing thesame way) stretch thechain backwards against
thechain stop (8), tighten thevice locking lever (10).
7. Take your hand off thechain and continue sharpening.
8. Continue in thesame way with all thecutting links that are facing thesame way.
9. Undo thelocking knob (2) on thebottom, turn thevice (9) and set thecorrect filing angle
for therest of thecutting links that face theother way, tighten thelocking knob (2) on
thebottom. Continue until thewhole chain is sharpened. Remember to unplug themachine
after use.
10. Discard thechain if thecutting edge is ground down to under 3 mm.
Raker Clearance, Setting the Cutting Depth of the Chain
It is therelationship between thecutting edge of thelink and theheight of theraker that
determines how much material is removed by thechain. It is therefore very important that this
relationship is maintained for thelife of thechain. Thecorrect clearance is very important both for
safety and optimum stock removal.
If thechain has been grinded 2 to 4 times (depending upon how much material has been ground
away) therakers might need to be filed down to maintain thesame raker clearance (and depth of
cut). Use aflat file and afile guide/depth gauge to file therakers.
ENGLISH
10
Cutting Edge Raker Clearance
Raker
If you do not have afile guide for setting theraker clearance you can use aflat file and file two
strokes off each of therakers as shown in thefigure.
Care and Maintenance
• Keep thesharpener free of dust and metal filings.
• Replace thegrinding wheel when it is worn down to Ø 75 mm.
• Store thesharpener in adry place out of children’s reach.
Responsible disposal
This symbol indicates that this product should not be disposed of with general
household waste. This applies throughout theentire EU. In order to prevent
any harm to theenvironment or health hazards caused by incorrect waste
disposal, theproduct must be handed in for recycling so that thematerial can
be disposed of in aresponsible manner. When recycling your product, take it to
your local collection facility or contact theplace of purchase. They will ensure that
theproduct is disposed of in anenvironmentally sound manner.
Transportation
Thepackaging that this machine comes in can be recycled. Thepackage should be handled with
care as it must not be subjected to knocks during its transportation.
Specications
Electrical grinder for sharpening chainsaw chains.
Power Supply 230 V AC, 50 Hz, 85 W
Output Power 85 W
Weight 2.4 kg
Grinding Wheel Size Outer diameter 108 mm, inner diameter (bore) 23 mm
Grinding Wheel Thickness 3.2 mm
Max. Speed 4800 RPM
Sound Power (Lwa) 93 dB(A)
Sound Pressure (LpA) 80 dB(A)
Compatible with these sizes of chain: Chain Pitch 1/4″– 0.325″– 3/8″– 0.404″
This manual suits for next models
4
Table of contents
Languages:
Other Cocraft Power Tools manuals
Cocraft
Cocraft KK-015P User manual
Cocraft
Cocraft PSJ750GH.1 User manual
Cocraft
Cocraft HMT300 User manual
Cocraft
Cocraft TY-MT300C-UK User manual
Cocraft
Cocraft GS150W2 User manual
Cocraft
Cocraft PRO EDITION MC300-T User manual
Cocraft
Cocraft LXC MTG18 User manual
Cocraft
Cocraft Pro Edition JT18-P User manual
Cocraft
Cocraft 18-3282 User manual
Cocraft
Cocraft ASYPHT04180 User manual
