CNC4PC C34HS2 User manual
USER’S
MANUAL
VER. 1
C34HS2 BOARD
Rev. 1
OCTOBER, 2020
User’s Manual Page i
USER'S MANUAL
TABLE OF CONTENTS
Contents Page #
1.0 OVERVIEW.....................................................................................................................1
2.0 FEATURES.....................................................................................................................1
3.0 BOARD DESCRIPTION..................................................................................................1
4.0 JUMPER TO SELECT THE ENABLE.............................................................................2
5.0 ALARM TERMINAL........................................................................................................4
6.0 WIRING SAMPLE...........................................................................................................4
7.0 PINOUT...........................................................................................................................5
8.0 DIMENSIONS..................................................................................................................6
User’s Manual Page 1
1.0 OVERVIEW
This board interface is used for the connection between C82, C76, M16D and Closed
Loop Steppers DRIVE.
2.0 FEATURES
•RJ45 Driver Input Connector
•Select Jumper for Hard Enable or Soft Enable.
•Alarm terminal
•Select jumper for signal differentials.
•Select Jumper active Low and active High
•Adjustable resistor to allow adjusting the fault sensibility
3.0 BOARD DESCRIPTION
User’s Manual Page 2
4.0 JUMPER TO SELECT THE ENABLE
Use Software Enable to keep the driver active only while the system is active.
Set of jumpers as shown in the image.
SOFT ENABLE
Use Hardware Enable to keep the driver enabled all the time.
Set of jumpers as shown in the image.
HARD ENABLE
JUMPER TO SELECT THE DIFFERENTIAL
If working the inputs of STEP and DIR as differentials signals, you have to use the board, set
jumper as shown in the image.
DIFERENTIAL
User’s Manual Page 3
If not use the differential signal for STEP & DIR, set jumper as show in the image.
STEP & DIR
JUMPER TO SELECT ACTIVE LOW AND ACTIVE HIGH
1-2: ACTIVE LOW
2-3: ACTIVE HIGH
User’s Manual Page 4
5.0 ALARM TERMINAL
6.0 WIRING SAMPLE
User’s Manual Page 5
7.0 PINOUT
C34HS CONNECTOR RJ45
RJ45 Pins
Function
1
NOT USED
2
PUL+
3
NOT USED
4
GND
5
ERR
6
DIR+
7
NOT USED
8 (5V)
EN+
User’s Manual Page 6
8.0 DIMENSIONS
All dimensions are in Millimeters.
DISCLAIMER
Use caution. CNC machines can be dangerous machines. Neither DUNCAN USA, LLC
nor Arturo Duncan are liable for any accidents resulting from the improper use of these
devices. This product is not a fail-safe device and it should not be used in life support
systems or in other devices where its failure or possible erratic operation could cause
property damage, bodily injury or loss of life.
Table of contents
Other CNC4PC Computer Hardware manuals
CNC4PC
CNC4PC C34ELP User manual
CNC4PC
CNC4PC C25XP User manual
CNC4PC
CNC4PC M26- 12R User manual
CNC4PC
CNC4PC C36S User manual
CNC4PC
CNC4PC C86ACCP6 User manual
CNC4PC
CNC4PC C34G320X User manual
CNC4PC
CNC4PC M26- 12R User manual
CNC4PC
CNC4PC C25 User manual
CNC4PC
CNC4PC C52- ESS User manual
CNC4PC
CNC4PC C34DE-B User manual
Popular Computer Hardware manuals by other brands
EMC2
EMC2 VNX Series Hardware Information Guide
Panasonic
Panasonic DV0PM20105 Operation manual
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 user manual
Gigabyte
Gigabyte B660M DS3H AX DDR4 user manual
Raidon
Raidon iT2300 Quick installation guide
National Instruments
National Instruments PXI-8186 user manual
