ClimateMaster CCE07 Series Guide

Console (CCE) Series

Tranquility Console

(TRC) Series

Commercial Console

Water-Source Heat Pumps

50Hz & 60Hz

Installation, Operation &

Maintenance Instructions

97B0035N01

Revision: 5 Nov., 2009B

Table of Contents

Model Nomenclature 3-4

General Information 5

Storage 6

Pre-Installation 6

Physical Data 7-9

Installation 10

Condensate Piping 11

Piping Connection 12-14

Piping Installation 15

Water-Loop Heat Pump Applications 16

Ground-Loop Heat Pump Applications 17

Ground-Water Heat Pump Applications 18

Water Quality Standards 20

Electrical Wiring - Line Voltage 21-23

Electrical Wiring - Low Voltage 24

Thermostat Wiring 25

Electrical Wiring Diagram Matrix 26

Electrical Wiring Schematics 27-31

CXM/DXM Controls 32-34

CXM/DXM Safety Control Reset 35-36

Unit Commissioning

and Operating Conditions 37

Piping System Cleaning and Flushing 38

Unit and System Checkout Procedure 39

Unit Start-Up 40

Unit Operating Conditions 41

Preventive Maintenance 43

Functional & Performance Troubleshooting 44-45

Refrigerant Circuit Diagram 46

Warranties 47-48

Revision History 50

THE SMART SOLUTION FOR ENERGY EFFICIENCY

Consoles

Rev.: 5 Nov., 2009B

climatemaster.com

Model Nomenclature: Console (CCE) Series

C C E AB0 7 CG S S C S R S

94 5 6

8 101112131415

CCE = Console

Power Termination

Revision Level

Voltage

Controls

Cabinet Construction

D = Bottom Return w/Locking Control Door

Subbase

A = Copper Water Coil w/E-Coated Air Coil

Heat Exchanger Options

C = Copper Water Coil

J = Cupro-Nickel Water Coil w/E-Coated Air Coil

N = Cupro-Nickel Water Coil

R = Right Piping

Piping Connections

L = Left Piping

Standard

B = Front Return

M = Bottom Return

D = 3” Subbase w/Motorized Damper

G = 5” Subbase

S = 3” Subbase

H = 5” Subbase w/Motorized Damper

N = None

V = Copper Water Coil w/E-Coated Air Coil & Extended Range Insulation

E = Copper Water Coil w/Extended Range Insulation

M = Cupro-nickel Water Coil w/E-Coated Air Coil & Extended Range Insulation

F = Cupro-nickel Water Coil w/Extended Range Insulation

1 2 3

S = Standard

None S F M

Motorized Water Valve A G N

Autoflow (2.25 Gpm/Ton) B H P

Autoflow (3.0 Gpm/Ton) C J Q

Motorized Water Valve & Afr (2.25) D K R

Motorized Water Valve & Afr (3.0) E L T

Secondary Circulation Pump U V W

Water Circuit Options

E = Front Return w/Locking Control Door

C = No Cabinet BR Chassis Only

Model Type

Unit Size

A = Field Connected (Hard Wire)

Sweat FPT MPT

C = Current

L = Bottom Return w/Locking Control Door

F = Front Return

S = Bottom Return

G = Front Return w/Locking Control Door

N = No Cabinet BR Chassis Only

With UltraQuiet

Without UltraQuiet

A = MCO Unit Mounted Tstat w/CXM

B = MCO Unit Mounted Tstat w/DXM

C = ACO Unit Mounted Tstat w/CXM

D = ACO Unit Mounted Tstat w/DXM

R = Remote Mounted Tstat w/CXM

S = Remote Mounted Tstat w/DXM

L = Remote Mounted w/CXM & LON

M = Remote Mounted w/DXM & LON

N = Remote Mounted w/CXM & MPC

P = Remote Mounted w/DXM & MPC

A = 115/60/1

E = 265/60/1

G = 208-230/60/1

B = 20Amp Plug & Cord

D = Disconnect Switch & 15Amp Fuse

F = Disconnect Switch (Non Fused)

H = 20Amp Plug, Cord, Receptacle,

Disconnect Switch & 15Amp Fuse

K = 20Amp Plug, Cord, Receptacle &

Disconnect Switch (Non Fused)

Rev.: 8 Aug, 2008B

J = No Cabinet FR Chassis Only H = No Cabinet FR Chassis Only

CLIMATEMASTER WATER-SOURCE HEAT PUMPS

Consoles

Rev.: 5 Nov., 2009B

4ClimateMaster Water-Source Heating and Cooling Systems

Model Nomenclature: Tranquility Console (TRC) Series (60Hz)

T R C AA0 9 CG S S C S R S

94 5 6

8 101112131415

TRC = Console

Power Termination

Revision Level

Voltage

Controls

Cabinet Construction

D = Bottom Return w/Locking Control Door

Subbase

A = Copper Water Coil w/E-Coated Air Coil

Heat Exchanger Options

C = Copper Water Coil

J = Cupro-Nickel Water Coil w/E-Coated Air Coil

N = Cupro-Nickel Water Coil

R = Right Piping

Piping Connections

L = Left Piping

V = Left Piping w/SS Drain Pan

W = Right Piping w/SS Drain Pan

Standard

B = Front Return

M = Bottom Return

S = 5” Subbase

H = 5” Subbase w/Motorized Damper

N = None

V = Copper Water Coil w/E-Coated Air Coil & Extended Range Insulation

E = Copper Water Coil w/Extended Range Insulation

M = Cupro-nickel Water Coil w/E-Coated Air Coil & Extended Range Insulation

F = Cupro-nickel Water Coil w/Extended Range Insulation

1 2 3

S = Standard

None S F M

Motorized Water Valve A G N

Autoflow (2.25 Gpm/Ton) B H P

Autoflow (3.0 Gpm/Ton) C J Q

Motorized Water Valve & Afr (2.25) D K R

Motorized Water Valve & Afr (3.0) E L T

Secondary Circulation Pump U V W

Water Circuit Options

E = Front Return w/Locking Control Door

C = No Cabinet BR Chassis Only

09, 12, 15, 18

A = Current Revision

Model Type

Unit Size

A = Field Connected (Hard Wire)

Sweat FPT MPT

B = Size 09 (115V) & Size 18 (265V)

L = Bottom Return w/Locking Control Door

F = Front Return

S = Bottom Return

G = Front Return w/Locking Control Door

N = No Cabinet BR Chassis Only

With UltraQuiet Without UltraQuiet

A = MCO Unit Mounted Tstat w/CXM

B = MCO Unit Mounted Tstat w/DXM

C = ACO Unit Mounted Tstat w/CXM

D = ACO Unit Mounted Tstat w/DXM

R = Remote Mounted Tstat w/CXM

S = Remote Mounted Tstat w/DXM

L = Remote Mounted w/CXM & LON

M = Remote Mounted w/DXM & LON

N = Remote Mounted w/CXM & MPC

P = Remote Mounted w/DXM & MPC

G = 208-230/60/1

B = 20Amp Plug & Cord

D = Disconnect Switch & 15Amp Fuse

F = Disconnect Switch (Non Fused)

H = 20Amp Plug, Cord, Receptacle,

Disconnect Switch & 15Amp Fuse

K = 20Amp Plug, Cord, Receptacle &

Disconnect Switch (Non Fused)

A = 115/60/1

E = 265/60/1

Rev.: 29 July, 2009B

J = No Cabinet FR Chassis Only H = No Cabinet FR Chassis Only

TRC FB12 EV S S E S R S

94 5 6

8 101112131415

TRC = Tranquility Console

POWER TERMINATION & OPTIONS

REVISION LEVEL

VOLTAGE

CONTROLS

CABINET

SUBBASE

A = Copper Water Coil w/E-Coated Air Coil

HEAT EXCHANGER OPTIONS

C = Copper Water Coil w/Non-CoatedAir Coil

J = Cupro-Nickel Water Coil w/E-CoatedAir Coil

N = Cupro-Nickel Water Coil w/Non-CoatedAir Coil

R = Right Piping

PIPING CONNECTIONS

L = Left Piping

S = STANDARD

F = Front Return (Standard)

S = Bottom Return (Standard)

S = 5” Subbase (Black)

H = 5” Subbase w/Motorized Damper

N = None

V = Copper Water Coil w/E-CoatedAir Coil & Extended Range Insulation

E = Copper Water Coil w/Non-CoatedAir Coil & Extended Range Insulation

M = Cupro-Nickel Water Coil w/E-CoatedAir Coil & Extended Range Insulation

F = Cupro-Nickel Water Coil w/Non-Coated Air Coil & Extended Range Insulation

1 2 3

Sweat FPT MPT

None S F M

Motorized Water Valve A G N

AutoFlow (2.25 gpm/ton) B H P

AutoFlow (3.0 gpm/ton) C J Q

Motorized Water Valve & AFR (2.25) D K R

Motorized Water Valve & AFR (3.0) E L T

WATER CIRCUIT OPTIONS

G = Front Return w/Locking Control Door (Standard)

N = No Cabinet Chassis Only (Standard)

B = CurrentRevision

SERIES

UNIT SIZE

OPTION

DISCONNECT

SWITCH

FIELD

CONNECTED

(HARD WIRE)

20 Amp

PLUG &

CORD

15 Amp

FUSE

RECEPTACLE

L = Bottom Return w/Locking ControlDoor (Standard)

V = 220-240/50/1

E = MCO Unit Mounted Tstat w/CXM

J = MCO Unit Mounted Tstat w/DXM

F = ACO Unit Mounted Tstat w/CXM

K = ACO Unit Mounted Tstat w/DXM

Q = Remote Mounted Tstat w/CXM

G = Remote Mounted Tstat w/DXM

H = Remote Mounted LON w/CXM

V = Remote Mounted LON w/DXM

T = Remote Mounted MPC w/CXM

U = Remote Mounted MPC w/DXM

Rev.: 21 Nov, 2007J

CE Mark

Model Nomenclature: Tranquility Console (TRC) Series (50Hz)

THE SMART SOLUTION FOR ENERGY EFFICIENCY

Consoles

Rev.: 5 Nov., 2009B

climatemaster.com

General Information

WARNING! To avoid the release of refrigerant into the

atmosphere, the refrigerant circuit of this unit must be

serviced only by technicians who meet local, state, and

federal proﬁciency requirements.

WARNING! All refrigerant discharged from this unit must be

recovered WITHOUT EXCEPTION. Technicians must follow

industry accepted guidelines and all local, state, and federal

statutes for the recovery and disposal of refrigerants. If a

compressor is removed from this unit, refrigerant circuit oil will

remain in the compressor. To avoid leakage of compressor oil,

refrigerant lines of the compressor must be sealed after it is

removed.

CAUTION!

To avoid equipment damage, DO NOT use

these units as a source of heating or cooling during the

construction process. The mechanical components and

ﬁlters will quickly become clogged with construction dirt

and debris, which may cause system damage.

 WARNING! 

 CAUTION! 

Safety

Warnings, cautions and notices appear throughout this manual.

Read these items carefully before attempting any installation,

service or troubleshooting of the equipment.

DANGER: Indicates an immediate hazardous situation, which

if not avoided will result in death or serious injury. DANGER

labels on unit access panels must be observed.

WARNING: Indicates a potentially hazardous situation, which if

not avoided could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation or an

unsafe practice, which if not avoided could result in minor or

moderate injury or product or property damage.

NOTICE: Notiﬁcation of installation, operation or maintenance

information, which is important, but which is not hazard-

related.

WARNING! Verify refrigerant type before proceeding. Units

are shipped with R-22, R-407c and R-410A (EarthPure

)

refrigerants. The unit label will indicate which refrigerant is

provided. The EarthPure

Application and Service Manual

should be read and understood before attempting to service

refrigerant circuits with R-407c or R-410A.

CLIMATEMASTER WATER-SOURCE HEAT PUMPS

Consoles

Rev.: 5 Nov., 2009B

6ClimateMaster Water-Source Heating and Cooling Systems

General Information

Inspection

Upon receipt of the equipment, carefully check the

shipment against the bill of lading. Make sure all units

have been received. Inspect the packaging of each unit,

and inspect each unit for damage. Insure that the carrier

makes proper notation of any shortages or damage on all

copies of the freight bill and completes a common carrier

inspection report. Concealed damage not discovered

during unloading must be reported to the carrier within

15 days of receipt of shipment. If not ﬁled within 15 days,

the freight company can deny the claim without recourse.

Note: It is the responsibility of the purchaser to ﬁle all

necessary claims with the carrier. Notify your equipment

supplier of all damage within ﬁfteen (15) days of shipment.

Storage

Equipment should be stored in its original packaging in

a clean, dry area. Store units in an upright position at all

times. Stack units a maximum of 3 units high.

Unit Protection

Cover units on the job site with either the original

packaging or an equivalent protective covering. Cap

the open ends of pipes stored on the job site. In areas

where painting, plastering, and/or spraying has not been

completed, all due precautions must be taken to avoid

physical damage to the units and contamination by foreign

material. Physical damage and contamination may prevent

proper start-up and may result in costly equipment clean-

up.

Examine all pipes, ﬁttings, and valves before installing

any of the system components. Remove any dirt or

debris found in or on these components.

Pre-Installation

Installation, Operation, and Maintenance instructions

are provided with each unit. Horizontal equipment is

designed for installation above false ceiling or in a ceiling

plenum. Other unit conﬁgurations are typically installed

in a mechanical room. The installation site chosen

should include adequate service clearance around the

unit. Before unit start-up, read all manuals and become

familiar with the unit and its operation. Thoroughly check

the system before operation.

Prepare units for installation as follows:

1. Compare the electrical data on the unit nameplate

with ordering and shipping information to verify that

the correct unit has been shipped.

2. Keep the cabinet covered with the original packaging

until installation is complete and all plastering,

painting, etc. is ﬁnished.

3. Verify refrigerant tubing is free of kinks or dents and

that it does not touch other unit components.

4. Inspect all electrical connections. Connections must

be clean and tight at the terminals.

5. Remove any blower support packaging.

6. Loosen compressor bolts on units equipped with

compressor spring vibration isolation until the

compressor rides freely on the springs. Remove

shipping restraints.

REMOVE COMPRESSOR SUPPORT PLATE 1/4”

SHIPPING BOLTS (2 on each side) TO MAXIMIZE

VIBRATION AND SOUND ATTENUATION.

CAUTION! DO NOT store or install units in corrosive

environments or in locations subject to temperature or

humidity extremes (e.g., attics, garages, rooftops, etc.).

Corrosive conditions and high temperature or humidity can

signiﬁcantly reduce performance, reliability, and service life.

Always move and store units in an upright position. Tilting

units on their sides may cause equipment damage.

NOTICE! Failure to remove shipping brackets from spring-

mounted compressors will cause excessive noise, and could

cause component failure due to added vibration.

 CAUTION! 

CAUTION! CUT HAZARD - Failure to follow this caution

may result in personal injury. Sheet metal parts may have

sharp edges or burrs. Use care and wear appropriate

protective clothing, safety glasses and gloves when

handling parts and servicing heat pumps.

THE SMART SOLUTION FOR ENERGY EFFICIENCY

Consoles

Rev.: 5 Nov., 2009B

climatemaster.com

Unit Physical Data

Model 07 09 12 15 19

Compressor (1 Each) Rotary

Factory Charge R22 (oz) [kg] 16 [0.454] 16 [0.454] 21 [0.595] 27 [0.765] 24 [0.680]

PSC Fan Motor & Blower (3 Speeds)

Fan Motor (hp) [W] 1/20 [27] 1/15 [50] 1/15 [50] 1/6 [124] 1/6 [124]

Blower Wheel Size (dia x w) -

(in) [mm]

5-1/4 x 6-1/4

[133 x 159]

5-1/4 x 6-1/4

[133 x 159]

5-1/4 x 6-1/4

[133 x 159]

5-1/4 x 6-1/4

[133 x 159]

5-1/4 x 6-1/4

[133 x 159]

Water Connection Size

O.D. Sweat (in) [mm] 5/8 [15.9] 5/8 [15.9] 5/8 [15.9] 5/8 [15.9] 5/8 [15.9]

Optional IPT Fittings (in) 1/2 1/2 1/2 1/2 1/2

Optional EPT Fittings (in) 1/2 1/2 1/2 1/2 1/2

Condensate Connection Size

I.D. Vinyl Hose (In) [mm] 5/8 [15.9] 5/8 [15.9] 5/8 [15.9] 5/8 [15.9] 5/8 [15.9]

Air Coil Size

Dimensions (h x w) - (in) [mm] 8 x 26 [20.3 x 66.0] 10 x 26 [25.4 x 66.0]

Filter Size

Bottom Return (in) [cm] 1 - 8 x 29-1/2 x 3/8 [20.3 x 74.9 x 0.95]

Front Return (In) [cm] 1 - 7 x 29-1/2 x 1/8 [17.8 x 74.9 x 0.32]

Cabinet Size

Bottom Return (Std. 3" Base)

(W x H x D) - (In) [cm] 48 x 24 x 12 [121.9 x 61.0 x 30.5]

Bottom Return (Std. 5" Base)

(W x H x D) - (In) [cm] 48 x 26 x 12 [121.9 x 66.0 x 30.5]

Bottom Return (No Subbase)

(W x H x D) - (In) [cm] 48 x 21 x 12 [121.9 x 53.3 x 30.5]

Unit Weight

Weight - Operating, (lbs) [kg] 173 [78.5] 177 [80.3] 187 [84.5] 193 [87.5] 198 [89.8]

Weight - Packaged, (lbs) [kg] 181 [82.1] 185 [83.9] 195 [88.5] 201 [91.2] 206 [93.4]

Console (CCE) Series

CLIMATEMASTER WATER-SOURCE HEAT PUMPS

Consoles

Rev.: 5 Nov., 2009B

8ClimateMaster Water-Source Heating and Cooling Systems

Unit Physical Data

Model 09 12 15 18

Compressor (1 Each)

Factory Charge R410A (oz) [kg] 28 [0.794] 29 [0.822] 33 [0.907] 39 [1.105]

PSC Fan Motor & Blower (3 Speeds)

Fan Motor (hp) [W] 1/20 [37] 1/12 [62] 1/8 [93] 1/8 [93]

Blower Wheel Size (dia x w) -

(in) [mm] - Qty 2 5.25 x 6.25 [133 x 159]

Water Connection Size

O.D. Sweat (in) [mm] 1/2 [12.7] 3/4 [19.1]

Optional IPT Fittings (in) 1/2 3/4

Optional EPT Fittings (in) 1/2 3/4

Condensate Connection Size

I.D. Vinyl Hose (In) [mm] 5/8 [15.9]

Air Coil Size

Dimensions (h x w) - (in) [mm] 8 x 26

[203 x 660] 10 x 26 [254 x 660] 10 x 32

[254 x 812]

Filter Size

Bottom Return (in) [mm] 1 - 10 x 30 x 1 [254 x 762 x 25] 1 - 10 x 36 x 1

[254 x 914 x 25]

Front Return (In) [mm] 1 - 7 x 29.5 x 1/8 [178 x 749 x 3.2] 1 - 7 x 35.5 x 1/8

[178 x 902 x 3.2]

Cabinet Size

Bottom Return (Std. 5" Base)

(W x H x D) - (In) [mm] 48 x 26 x 12 [1219 x 660 x 305] 54 x 26 x 12

[1372 x 660 x 305]

Front Return (No Subbase)

(W x H x D) - (In) [mm] 48 x 21 x 12 [1219 x 533 x 305] 54 x 21 x 12

[1372 x 533 x 305]

Cabinet Size

Weight - Operating, (lbs) [kg] 175 [79] 180 [82] 190 [86.2] 220 [99.8]

Weight - Packaged, (lbs) [kg] 185 [83.9] 190 [86] 200 [90.8] 232 [105.2]

* Data not available at time of publication.

All units have rubber grommet compressor mountings and TXV expansion devices.

Tranquility Console (TRC) Series (60Hz)

THE SMART SOLUTION FOR ENERGY EFFICIENCY

Consoles

Rev.: 5 Nov., 2009B

climatemaster.com

Unit Physical Data

Tranquility Console (TRC) Series (50Hz)

Model 09 12 15 18

Compressor (1 Each) Rotary

Factory Charge R410A (oz) [kg] 26 [0.737] 29 [0.822] 33 [0.936] 30 [0.850]

PSC Fan Motor & Blower (3 Speeds)

Fan Motor (hp) [W] 1/20 [37] 1/12 [62] 1/8 [93] 1/8 [93]

Blower Wheel Size (dia x w) -

(in) [mm] - Qty 2 5.25 x 6.25 [133 x 159]

Water Connection Size

O.D. Sweat (in) [mm] 1/2 [12.7] 3/4 [19.1]

Optional IPT Fittings (in) 1/2 3/4

Optional EPT Fittings (in) 1/2 3/4

Condensate Connection Size

I.D. Vinyl Hose (In) [mm] 5/8 [15.9]

Air Coil Size

Dimensions (h x w) - (in) [mm] 8 x 26

[203 x 660] 10 x 26 [254 x 660] 10 x 32

[254 x 813]

Filter Size

Bottom Return (in) [mm] 1 - 10 x 30 x 1 [254 x 762 x 25] 1 - 10 x 36 x 1

[25.4 x 91.4 x 2.5]

Front Return (In) [mm] 1 - 7 x 29.5 x 1/8 [178 x 749 x 3.2] 1 -7 x 35.5 x 1/8

[178 x 902 x 3.2]

Cabinet Size

Bottom Return (Std. 5" [127] Base)

(W x H x D) - (In) [mm] 48 x 26 x 12 [1219 x 660 x 305] 54 x 26 x 12

[1372 x 660 x 305]

Front Return (No Subbase)

(W x H x D) - (In) [mm] 48 x 21 x 12 [1219 x 533 x 305] 54 x 21 x 12

[1372 x 533 x 305]

Cabinet Size

Weight - Operating, (lbs) [kg] 175 [79] 180 [82] 190 [86.2] 220 [99.8]

Weight - Packaged, (lbs) [kg] 185 [83.9] 190 [86] 200 [90.8] 232 [105.2]

All units have rubber grommet compressor mountings and TXV expansion devices.

CLIMATEMASTER WATER-SOURCE HEAT PUMPS

Consoles

Rev.: 5 Nov., 2009B

10 ClimateMaster Water-Source Heating and Cooling Systems

Installation

1. Console units are typically installed along an outside

wall of the room. Provide adequate space in front

of the unit for service and maintenance. Locate

the Console Unit so that it provides adequate air

circulation throughout the room.

2. Unpack the Console Unit from the shipping carton.

Remove the front cabinet by lifting up and away from

the backplate. Protect the cabinet from damage

during installation by returning it to its original

packaging until required.

3. Remove compressor isolation plate shipping screws

(4) as shown in Figure 1a. (All CCE and TRC09-12)

4. Using a carpenter's square and a level, ensure the

unit is level. Shim the unit if necessary to assure

proper installation.

5. Select the proper fasteners to connect the backplate

securely to the wall.

6. Fasten the backplate onto the wall through the screw

holes located in the back ﬂange. Secure the subbase

in place.

7. Make all necessary electrical connections as

described in the Electrical Wiring section of this

manual. Consult the wiring diagram to ensure proper

hook-up.

8. Connect the ﬁnal piping as described in the Supply

and Return Piping and Condensate Piping section

of the manual. Install shut-off valves, piping and/or

hoses and other accessories as speciﬁed.

9. Before making the ﬁnal water connections, ﬂush

the system as described in the Start Up section

of this manual. After ﬂushing the system, connect

piping and hoses to the proper supply, return and

condensate connections of the unit.

NOTE: When necessary, use adapters to connect hoses.

10. Install any other system components as required

following manufacturer's instructions.

11. After Start-up, reinstall the front cabinet by

carefully lowering the front cabinet over the chassis

onto the backplate.

Supply and Return Hoses

Optional pressure-rated hose assemblies are available

for use with ClimateMaster Console Units. Use the

following guidelines when installing supply and return

hose assemblies.

1. Install supply and return hoses ﬁtted with swivel-joint

ﬁttings at one end to prevent the hose from twisting.

2. Use adapters to secure the hose assembly to the unit

and the riser.

3. Do not allow the hose to twist during installation.

Twisting may damage the hose wall or the interior

rubber compound.

4. Use pipe joint compound sparingly on the pipe

threads of the ﬁtting adapters.

5. Prevent sealant from reaching the ﬂared surfaces of

the joint.

6. Do not use pipe joint compound when teﬂon thread

tape is pre-applied to hose assemblies or when

ﬂared-end connections are used.

7. Maximum torque which may be applied to brass

ﬁttings is 30 ft-lbs [41 N-m]. When a torque wrench

is not used, tighten brass ﬁttings ﬁnger-tight plus one

quarter turn.

8. Tighten steel ﬁttings as necessary.

9. Shut-off/balancing valves, ﬂow indicators, and drain

tees in the supply runout and return at each ﬂoor to

aid in loop balancing and servicing.

The installation of Console Water-Source Heat Pumps

and all associated components, parts and accessories

that make up the installation shall be in accordance with

the regulations of ALL Authorities having jurisdiction

and MUST conform to all applicable Codes. It is the

responsibility of the Installing Contractor to determine

and comply with ALL applicable Codes and Regulations.

NOTE: An Installation Checklist is provided in this

manual. Complete this checklist after all installation

procedures are completed. A periodic maintenance

checklist provided in the Maintenance section outlines

recommended maintenance schedules. A Start-Up

Inspection Log is also included at the end of this manual

to encourage thorough unit checkout at initial start-up.

These checklists are not a substitute for the detailed

information found in the Installation section of this

manual

Poor or inadequate installation may result in noisy unit

operation or unattractive installation.

 CAUTION! 

Figure 1a: Compressor Shipping Screws (All

CCE and TRC 09-12)

4 Shipping

Screws

This manual suits for next models

Table of contents

Other ClimateMaster Heat Pump manuals

ClimateMaster

ClimateMaster tranquility 30 Owner's manual

ClimateMaster

ClimateMaster Tranquility Water-to-Water THW 008 Owner's manual

ClimateMaster

ClimateMaster Tranquility 27 Guide

ClimateMaster

ClimateMaster CS Series User manual

ClimateMaster

ClimateMaster 803 series General instructions

ClimateMaster

ClimateMaster Tranquility TCH Series Owner's manual

ClimateMaster

ClimateMaster Tranquility TTD026 Series Owner's manual

ClimateMaster

ClimateMaster TMW Series Owner's manual

ClimateMaster

ClimateMaster Tranquility TR Series Guide

ClimateMaster

ClimateMaster TRANQUILITY LARGE Series Owner's manual

ClimateMaster

ClimateMaster Tranquility 30 Series Guide

ClimateMaster

ClimateMaster GLW Series Guide

ClimateMaster

ClimateMaster Tranquility TY Series Owner's manual

ClimateMaster

ClimateMaster Tranquility Digital DXM2 User manual

ClimateMaster

ClimateMaster Tranquility 30 Digital TE Series Owner's manual

ClimateMaster

ClimateMaster Trilogy VE Series Guide

ClimateMaster

ClimateMaster Genesis Standard (GR) Series Guide

ClimateMaster

ClimateMaster Tranquility Quick start guide

ClimateMaster

ClimateMaster Tranquility 16 Compact Series Instruction manual

ClimateMaster

ClimateMaster GT-PX Indoor Split Series User manual

ClimateMaster

ClimateMaster TMW036 Owner's manual

ClimateMaster

ClimateMaster Tranquility 16 Series Owner's manual

ClimateMaster

ClimateMaster TYH/V 024 - 060 60Hz - HFC-410A Manual

ClimateMaster

ClimateMaster HS series Assembly instructions

Popular Heat Pump manuals by other brands

MICROWELL

MICROWELL HP 1000 GREEN Installation and user manual

Sanyo

Sanyo SAP120FCH Service manual

Daikin

Daikin EHYHBH05AA Operation manual

Panasonic

Panasonic WH-SDF03E3E5 Design handbook

Bryant

Bryant 544B Specifications

Airxcel

Airxcel 45000 Series Installation, operation and maintenance instructions

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Service manual

Dimplex

Dimplex LI 16I-TUR Installation and operating instruction

Carrier

Carrier WSHP Open v3 Integration guide

TGM

TGM CTV14CN018A Technical manual

Carrier

Carrier 38MGQ Series installation instructions

Kokido

Kokido K2O K880BX/EU Owner's manual & installation guide

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Installation and service instructions

Carrier

Carrier 48EZN installation instructions

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Installation and service instructions for contractors

Ariston

Ariston NIMBUS user manual

Weishaupt

Weishaupt WWP L 7 Installation and operating instruction

GE Zoneline AZ85H09EAC datasheet