Clevertronics LP CSBLED Series Installation and operating instructions

1943075 V2.6 March 2019

Testing:

Once connected to the 240V mains supply, the unit must be allowed to charge the battery for at least 24

hours. Conduct the following tests:

•For the first test, the emergency lamp must remain illuminated for at least 2 (4 for the -4HR) hours

after disconnection from the mains supply.

•Subsequent tests require the unit to illuminate for at least 90 minutes (4 hours for -4HR). The results

of all tests are required to be recorded in a service logbook, which is to be kept on-site at all times.

If the unit fails to remain illuminated for the requisite time, remedial action must be taken to repair

the situation and once completed, the unit must pass a subsequent test. For more specific

information, please refer to the current edition of the AS 2293.3 Standard.

Swingblade Maintenance:

Battery/Lamp Replacement:

•Prise off the plastic end caps from ends

using a terminal screwdriver

•Disconnect the lamp lead from the PCB

and slide out the LED light bar.

•Reinsert new LED light bar, reconnect the

lamp lead and replace the plastic end cap..

•Remove the central screw connecting the

two earth leads to the earth bar. This screw

holds the equipment tray in place.

•Slide the gear tray out from the test

switch/light bar end, unplugging the AC

connector once it is revealed.

•Unplug the battery lead then bend back the

metal tabs securing the battery pack.

Remove the battery and replace with the

changeover battery pack.

•Re-assemble the fitting reversing the above

procedure. It is important that the screw

securing the two earth leads is re-installed

and tightened correctly.

Trouble Shooting:

Below are a list of common problems and their

possible causes.

Fault: The Green LED Test Switch

indicator is not illuminated.

Check: A.C. is connected and is turned on.

Battery is connected

Test Switch for damage.

Fault: Lamp does not illuminate in

emergency mode.

Check: A.C. is connected.

Lamp is correctly inserted.

Battery is connected

Fault: Lamp illuminates in emergency

mode, but only stays on for a short

period.

Check: Battery has been allowed to charge for

at least 24 hours.

Battery for damage.

Rated Emergency Lumen Output in accordance with AS2293.1 (refer

to spacing tables for installation positions):

Refer to tech label for classification details (Not applicable to TH version).

Caution:

On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during

construction. As a result, any Exit & Emergency Units, on these circuits, will have their batteries

discharged or “cycled”. The battery in this fitting has been selected to give excellent long life performance

in a controlledAS2293 testing environment. Excessive battery cyclingwill reduce through-life performance

and may lead to premature battery failure. Battery warranty claims, as a result of such abuse, are

specifically EXCLUDED from Clevertronics warranty terms.

Warranty:

For Product Warranty information and Terms and Conditions of Sales please refer to our website

http://clevertronics.com.au/terms-conditions-sale-australia-nz/

LP™ Swingblade LED

Installation & Maintenance Instruction Leaflet

Designed in Australia to comply with the

requirements of AS2293.3: 2005 and AS/NZS

CISPR15: 2011.

NOTE: Standard product codes with this symbol are

enabled with Clevertest Plus capability. Please refer

to the operation guide supplied with the product for

details.

Victoria (Head Office & Manufacturing)

195 Chesterville Rd Moorabbin VIC 3189

Phone: +61 3 9559 2700

Fax: +61 3 9559 2799

News South Wales

Phone: +61 2 8805 6400

Fax: +61 2 8805 6444

Queensland

Phone: +61 7 3442 9700

Fax: +61 7 3442 9777

South Australia/Northern Territory

Phone: +61 8 8301 8800

Fax: +61 8 8351 8286

Western Australia

Phone: +61 8 9248 3720

Fax: +61 8 9248 3725

New Zealand

Phone: +64 800 548 448

Models:

CSBLED-yy-xx-ss-zz

CCSBLED-yy-xx-ss-zz (Classic blade option)

Testing:

Options:

Special Legend

ss = SP

Manual Test

xx = Blank

4 Hour runtime

zz = 4HR

Zoneworks

xx = ZW

Fire Panel Sound Control

zz = SND-24V

Zoneworks DATA

xx = DATA

Zoneworks Sound Control

zz = SND

DALI Compatible

xx = DALI

Theatre

yy = TH

Clevertest

xx = CT (NOTE: Products supplied with the Clevertest Plus Symbol are

activated with Clevertest PLUS capability. Please refer to the operation guide

supplied with the product for details).

Spare Parts:

1550070

BATT: LP 3.2V 3200mAh 200mm lead, sp.BRKT

1550235

BATT: LP -4HR 3.2V 6400mAh.200mm lead.Brkt

8002355

PCA: Swingblade LED Driver

8002354

PCA:LBSLED-TH #CT10164-L4 6C20 (for use with -TH options)

8002185

PCA: Swingblade Duris LED Strip

Important:

It is illegalfor anyone, except for a licensed electrician toinstall ormaintain this product. Before installation,

ensure that the electricity supply has been switched off and isolated. Installation must be carried out in

accordance with the relevant Australian and International Standards.

1943075 V2.6 March 2019

Installation:

The LP Swingblade LED Exit (CSBLED) is a surface mount (wall or ceiling) fitting. The CSBLED can be

attached directly to any solid surface, or to a ceiling tile using the integrated mounting bracket. Please

follow the steps below to install the CSBLED Exit:

•Remove the mounting bracket from the fitting.

•Using the bracket as a guide, mark 2 holes for mounting screws. Then install the bracket.

•Connect the 240VAC supply.

•Insert the CSBLED body into the bracket and slide to lock into position.

•If the CTP capabilities are activated please affix the CTP status Label to a visible surface.

NOTE: If product is suspended below the ceiling or mounted on a metal surface the Swingblade

bracket cover plate accessory (S/N:2740100) is required to cover the mains terminals.

Networking:

When installing the product on a monitored network, (ZONEWORKS, DATA, DALI) simply insert the

relevant Smart Node PCA.

Changing Diffuser Decals: (Not applicable to CCSBLED and –TH

options)

The Swingblade Exit uses Clevertronics patented “Tamper proof” Exit legend cover and comes complete

with spare legend inserts to enable straight on, left or right arrow as well as SS/DS combinations.

The tamper proof cover is held in place by 3 locking tabs recessed in the top edge of the diffuser. Use a

tool to disengage and push the locking tabs through to release the cover and remove the insert, replacing

it with the desired one.

To re-install the clear cover, first engage the three small lugs on the bottom of the cover into the respective

recesses in the diffuser. Once you are sure the lugs are located, carefully push the 3 locking tabs back in

to complete the process.

Clevertronics Clevertest and Clevertest Plus

Refer to the supplementary operation guide supplied with the Product.

After Power ON, the Status LED on a Clevertest Plus enabled fitting will display a rapid Green or Red

flashing for a period up to 2 minutes.

Zoneworks and DATA Monitored Options

Swingblades with part numbers CSBLED-ZW, CSBLED-DATA are fitted with Zoneworks communications

modules (nodes).These fittings are monitored using either Powerline Carrier Technology that utilises the

power cable to provide data communication or a dedicated data cable to/from data routers installed on a

dedicated data trunk connected to a central Server (can also be connected via Ethernet/Internet/Fibre).

Zoneworks software on the server is used to monitor, coordinate testing and collate test data from each

Swingblade and can be commissioned by a single push of the test switch, or scanning of the supplied

barcode. The LED Test Switch indicator provides a multifunction indication of the status of the Swingblade

during testing and normal operation:

State

LED Operation

Commissioned

LED on Solid (Green)

Un-commissioned

LED flashes at 0.5Hz (0.5s Green, 0.5s Yellow)

Emergency Light Test In Progress

LED flashes at 3s On (Yellow) & 0.5s Off

In the case of the DATA version a 2-way “figure 8” cable and terminal block facilitates the connection to

the DATA network via a multi-drop bus (daisy chain connection). For further information of installation of

a Zoneworks LW system, please refer to the Zoneworks Users Guide and Commissioning Guide (incl.

DATA version)

DALI EM Option

Swingblades with part numbers CSBLED-DALI are fitted with DALI modules (nodes) that facilitate

connection and integration to 3rd Party Lighting Control Systems. Before installing the CSBLED-DALI

please confirmthat the Lighting Control System has the capability tomonitor DALI Emergency Luminaires.

The CSBLED-DALI will be addressed and configured into the control system by the Lighting Control

System Commissioning Technicians and not Clevertronics.

State

LED Operation

Commissioned/ Un-commissioned

LED on Solid (Green)

Emergency Light Test in progress

LED flashes at 1s On (Yellow) & 1s Off

“IDENTIFY COMMAND”

Fitting goes into emergency mode for 10 seconds

A 2-way “figure 8” cable and terminal block facilitates the connection to the DALI network. DALI

connections are marked as Da Da.

Press locking tab and slide to remove from bracket

Mounting Bracket

Locking Tab

Locking Tabs

This manual suits for next models

Other Clevertronics Lighting Equipment manuals

Clevertronics

Clevertronics L10 LSBLED Series Installation and operating instructions

Clevertronics

Clevertronics CleverEVAC LP UltraBlade DYGC UP Series Installation and operating instructions

Clevertronics

Clevertronics CBULKy Series Installation and operating instructions

Clevertronics

Clevertronics L10 Ultrablade Pro LUBPRO-SM Series Instruction Manual

Clevertronics

Clevertronics TS Trade Series Installation and operating instructions

Clevertronics

Clevertronics CLP CCFPRO Series Installation and operating instructions

Clevertronics

Clevertronics CLP Argonaut ARGOSQ-LP Series User manual

Clevertronics

Clevertronics ECFLED-LI-TH Series Installation and operating instructions

Clevertronics

Clevertronics EJELED-40-LI Installation and operating instructions

Clevertronics

Clevertronics ELIFE-X-LI Installation and operating instructions

Clevertronics

Clevertronics CLP Ultrablade Pro CUBPRO Series Manual

Clevertronics

Clevertronics Trade TS CIRCLITE ECLLED Series Installation and operating instructions

Clevertronics

Clevertronics CleverEVAC L10 Cleverfit Pro DYRL CP Series Installation and operating instructions

Clevertronics

Clevertronics CleverEVAC LP Cleverfit Pro DYRC CP Series Installation and operating instructions

Clevertronics

Clevertronics L10 CleverFit Exit LCFLED Series User manual

Clevertronics

Clevertronics L10 Cleverfit LCFLED Series Installation and operating instructions

Clevertronics

Clevertronics L10 LUBPRO Series Manual

Clevertronics

Clevertronics L10 LIFELIGHT PRO LLIFE PRO Series User manual

Clevertronics

Clevertronics LP Argonaut Instruction Manual

Clevertronics

Clevertronics l10 LBULKy Series Installation and operating instructions

Clevertronics

Clevertronics Trade Series Manual

Clevertronics

Clevertronics L10 LVP2LEDM-P Series Installation and operating instructions

Clevertronics

Clevertronics L10 Supalite LFLLED Series User manual

Clevertronics

Clevertronics LP LIFELIGHT CLIFE-RECSP Series Installation and operating instructions

Popular Lighting Equipment manuals by other brands

Brizo

Brizo 8SP-MU-4 manual

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 installation instructions

IKEA

IKEA BJÖRKSPIREA manual

Laserworld

Laserworld Evolution Series ES-400RGB manual

Alien

Alien RG STAR user manual

EuroLite

EuroLite LED B-40 user manual

Qazqa

Qazqa Suplux SL 3 Black 103062 instruction manual

Commercial Electric

Commercial Electric 54568141 Use and care guide

CREE LIGHTING

CREE LIGHTING 304 Series installation instructions

Goobay

Goobay 49867 user manual

ECOMAN ITALIA

ECOMAN ITALIA LED T8 instruction manual

Alkalite

Alkalite Krypton KT-81 user manual

Clas Ohlson

Clas Ohlson GU10 manual

DTS

DTS DELTA 10 F user manual

ring

ring Solar Steplight manual

One Stop Gardens

One Stop Gardens 57696 Owner's manual & safety instructions

Chauvet DJ

Chauvet DJ COREpar UV120 ILS user manual

SIREM

SIREM Swimeo A2 instructions