Clear Water Emperor User manual

Please read carefully prior to commencing any work.

Any installation should only be carried out by a qualified tradesman with knowledge of the

Statutory Regulations and plumbing requirements for your area.

HANDLING

Please note that this product has been through our rigid quality control procedures which

include a thorough visual inspection under bright lights water testing etc. Please unwrap the

bath and check it carefully to ensure it has not been damaged in handling or transport which

is beyond our control.

Do not remove the old fixture before you unpack and inspect the new unit.

Upon receipt, check for shortages. Report any shortages immediately.

Store the bath and wall surrounds in a safe place until you begin installation to avoid

damage.

Claims regarding cracks and/or face damage must be reported

within 24 hours of receipt of the product. No such claims will be

recognised after installation as this is classed as acceptance of the

product.

The bath should not be exposed to direct flame or abnormal heat. Once installed it is good

practice to cover the entire bath with a soft protective cloth until other trades have completed

their work.

.CAUTION: Risk of product damage.

•It is advisable always to run in some cold water before turning

on the hot tap

•Do not use abrasive cleaners.

•Wipe your bath with a soft cloth after each use to prevent a

build-up of soap and residue.

•Avoid cleaning products that contain acetone, ethyl alcohol,

amyl or ethyl acetate, sodium

hypochlorite, toluene, or phenol. These products can damage

the finish

•Extreme heat such as that generated by cigarettes or portable

heaters can damage Acrylic surfaces. Do not use such items

near your bath.

•In the event of slight scratches in the bath surface, a mild

abrasive, similar to metal polish, can be used to polish these

out.

The Emperor Bath

Installation Instructions

FOR TECHNICAL ADVICE/ SPARE PARTS

PLEASE CONTACT OUR CUSTOMER

SERVICES DEPARTMENT

Tel. 01274 738140 Fax. 01274 732461

TO THE INSTALLER

Please leave the instruction leaflet for the

customer

Clearwater Collection Ltd

Enterprise House, Ironworks Park

Bowling Back Lane, Bradford

BD4 8SX

The Bath Instructions

This bath is suitable for plastic wastes or exposed wastes. These are available

to purchase separately.

1. The bath is designed for floor or wall mounted taps.

2. The floor which the bath sits on must be level.

3. There is access under the bath for the connection of the outlet pipe

to the trap. (See Fig 1.)

4. This access point on the base can be enlarged if required, but should

not extend beyond the base up the sides walls.

5. The bath can be tipped up slightly to allow connection to the drain

piping running into the floor void, or a length of flexible pipe can be

used. (See fig. 2)

Connecting the waste to the drain pipe

There are two ways in which you can connect

the drain pipe to the waste.

Method 1) If you have a waste that comes up through the floor, you can connect to it

with a flexible drain pipe which enables you to tilt the bath up and move the

bath into the required position. (see fig 3) To avoid water retention in the

trap the flexible pipe should have a continuous downward flow

Method 2) If under-floor access is impossible, an additional hole of approx 45mm

diameter can be drilled through the outer skin of the bath to allow the trap to

be connected to a rigid pipe(see fig 4)

Very important

Check for leaks before securing to floor

Once the waste connection has been made, with the plug in, run a little

water into the bath and check for leaks. Take the plug out and let water

drain. Check again for leaks. Then fill the bath past the over flow, empty and

check for leaks again.

Securing your bath to the floor

When the bath is in position and the installation is complete,

It is recommended that you apply clear silicone sealant around the bottom

of the bath to secure it to the floor (Circles shown in Fig 2).

Should maintenance access be needed the silicone can be released by

cutting round it with a sharp knife.

Fig 1

Fig 4

Fig 3

Fig 2

Other Clear Water Bathtub manuals

Clear Water

Clear Water clearspa User manual

Popular Bathtub manuals by other brands

Agua

Agua BARTOLI-66 quick start guide

PAA

PAA PRELUDE owner's manual

BETTE

BETTE SILHOUETTE installation guide

Kohler

Kohler K-820-GC Roughing-In Guide

American Standard

American Standard Whirlpool/Bathing Pool 2748.XXXW installation instructions

Oliveri

Oliveri Naples installation instructions

Lyons

Lyons Elite ETLxx663219 Series manual

Woodbridge

Woodbridge BJ500 Installation and care guide

Whirlpool

Whirlpool Ariel ARL-702 installation manual

TEIKO

TEIKO EXCELLENT DUO user manual

American Standard

American Standard Colony 5-1/2' x 32" Specification sheet

American Standard

American Standard 3052OD.X0X Installation instructions and owner's manual

Kohler

Kohler K-1111-H2 Roughing-In Guide

agape

agape MARSIGLIA AVAS1075 Assembly instructions

Kohler

Kohler K-1151 Homeowner's guide

Kohler

Kohler K-1158 Roughing-In Guide

Kohler

Kohler K-1244 Homeowner's guide

Kallista

Kallista P50045-G5 Homeowner's guide