CleanStation SRS-DT3 User manual

CleanStation Dimension SRS-DT3

Jet action cleaning

Rules for Safe Operation

Important: Do not attempt to operate the CleanStationTM until you have read thoroughly and understand all

instructions and safety rules contained in this manual. Failure to comply may result in personal injury.

•As a normal industry safety practice, be sure the machine has been plugged into a 115VAC ground fault interrupt outlet.

•Protective neoprene gloves, as well as protective eye goggles should be worn when cleaning parts in the CleanStationTM.Having a source of fresh water

nearby is helpful to wash off any solution that splashes on exposed skin or parts. During normal operation of the CleanStation, the tank and lid will

become hot (up to 150F). Care should be taken to avoid exposed skin touching these hot surfaces causing a burn.

•Use stainless steel or plastic tongs to insert and remove parts from the CleanStationTM tank. DO NOT use aluminum tongs.

•Ambient lighting in the area where CleanStationTM is setup and used needs to be sufficient for the contents of the CleanStation to be seen with ease.

Artificial lighting that achieves an intensity of 200 to 300 Lux is usually sufficient.

•When the CleanStationTM is cleaning parts, it should NOT be left unattended.

•When operating the CleanStationTM, facing the front provides an unobstructed view of the control panel display, as well as direct access to the power

switch in case quick shutdown is necessary. All normal operations should be performed facing the front, with the exception of accessing the drain valve,

which is located on the back of the CleanStationTM.

•CleanStationTM weights approximately 63lb empty and should NEVER be moved when liquid is present in the tank. Sections 9 and 10 of the

Operations guide detail how to properly drain and dispose of used chemical solution prior to moving the CleanStationTM.

•CleanStationTM is designed for indoor use only, at room temperatures between 65F and 80F. CleanStation will not operate at a temperature at or below

40F.

•CleanStationTM is designed for cleaning with WaterWorks Soluble Concentrate (or other suitable substitute recommended by Stratasys, Inc. or PM

Technologies), to clean P400-ABS modeling and P400-SR support material. It is NOT designed for cleaning or heating food, cosmetic or medical

products, nor metal or other non-water soluble plastic parts. Do not use chemicals that are not pre-qualified by PM Technologies, this will result in

voiding the warranty.

•CleanStationTM should NOT be used in an explosive atmosphere. Normal internal sparking of the pump motor could ignite fumes.

•CleanStationTM has a working dimension inside the tank of 10 inch by 11 inch by 12-1/4” inch. Be careful not to insert too many parts (to be cleaned) so

as to overflow the level of the tank.

CleanStation Dimension SRS-DT3

Jet action cleaning

Technical Specifications

•Outside machine dimensions: 19-1/4 inch height by 23-1/2 inch width by 21-1/2 inch depth

•Inside tank dimensions: 10”d x 11”h x 12-1/4”w

•Tank holds 6 gallons of water

•Weight (empty): 63lb

•Power consumption: 12amps at 115VAC

•Fuses: Class G fuse, Type SC, 15 Ampere

•Operating temperature: 150F

CleanStation Dimension SRS-DT3

Jet action cleaning

3. Connecting the drain

The CleanStationTM drain is located at the rear of the unit (see Figure 2). Install a standard 3/4” inside diameter hose to the 3/4”

barbed fitting attached to the drain valve.

4. To operate the system

Please review the previous section entitled "Rules for Safe Operation", then proceed to the next section "Operation".

Installation

1. Selecting a location

Select a clean, dry, well-lighted area with a minimum clearance of

six inches between the CleanStationTM and any adjacent walls. It is

especially important to select a level surface, due to liquid levels in

the tank.

The ideal room temperatures for the system are between 65F and

80F.

2. Power requirements

The CleanStationTM requires 115VAC, 60Hz, 15amp service. As a

normal industry safety practice, a ground fault interrupt outlet

must be used. drain valve

(shown shut)

Figure 2

CleanStation Dimension SRS-DT3

Jet action cleaning

Operation

Up and Down keys

On the Home Page, adjusts the set

point while holding Set Key & pressing

up or down arrow keys. Machine must

be running while this is done.

Also used to increase or decrease hours

and minutes in the Operations Page.

Timer Indicator

Colon blinks when

timer is timing

Set key

Infinity key

Returns to the Home Page.

Press and hold the Infinity Key

for about 2 seconds to enter the

Operations Page, where hours

and minutes can be changed.

Four Digit, LED Display: Lit when heater is on

Pump and Heater

enable indicator

Lit when enabled.

Not used

Lit when pump is on

CleanStation Dimension SRS-DT3

Jet action cleaning

Operation

Figure 3

2. Adding water to the tank

Verify the drain valve on the back of the unit (see Figure 2) is closed, that the power cord

is unplugged, and that a drain line has been securely installed as described in the

Installation instructions, step 3. Fill the tank until the water is one inch from the top of the

tank (approx. 6 gallons). Try to anticipate the volume of parts being cleaned; adding too

many parts will cause the water level to overflow. To solve the potential problem reduce

the volume of water initially being added.

Note that there is a level switch approximately 1 inch below the top of the tank. The

CleanStationTM will not operate if the water level drops below this switch.

3. Powering up the system

Verify the power switch (see Figure 3) on the front panel is off by depressing the right

side of the switch. As a normal industry safety practice, plug the power cord into a

115VAC ground fault interrupt outlet and turn the power switch on by pressing the left

side of the switch. The controller display will light. The display will first show ,

then , then which is the time remaining and is also where the “Home Page”

is located. To display the current water temperature, press and release on the

controller (see Figure 3). The that is seen when pressing and holding is the

low temperature set point and must remain off to avoid damaging the machine.

power switch

"down arrow key"

"up arrow key"

”set key”

1. Necessary supplies to operate

•Protective neoprene gloves, as well as protective eye goggles should be worn when cleaning parts at the CleanStationTM. Having a

source of fresh water nearby is helpful to wash off any solution that splashes on exposed skin.

•Use stainless steel or plastic tongs to insert and remove parts. DO NOT use aluminum tongs.

•WaterWorks Soluble Concentrate P400SC, 1.05lb (1/2 of a 2.1lb bottle).

•Fresh water (ambient temperature), approximately 6 gallons.

”infinity key"

CleanStation Dimension SRS-DT3

Jet action cleaning

4. Start the cleaning cycle

IMPORTANT: Once the system is started, immediately proceed to the next step of adding concentrate; it is very important to add the

WaterWorks Soluble concentrate before the water gets too warm (86F). Failure to do this may cause the chemical to have an adverse

reaction with the water.

To start the CleanStationTM push on the controller (see Figure 3).

The CleanStationTM will continue to run until the timer counts down to zero, at which time the system will shut off automatically.

Pressing will manually stop the cleaning cycle.

IMPORTANT: To immediately power off the CleanStationTM (in case of emergency), turn the power switch off and unplug the power

cord.

5. Temperature setting

The controller is preset to heat and maintain the water temperature at 150F (recommended by Stratasys) WARNING: running the

machine above 150F will void the warranty. To change this setting the machine must be running; if it is not running press to start the

machine. WARNING: if the machine isn’t running when changing temperature you may damage the heater. Then press and

hold and use or to select the desired temperature. Parts are most efficiently cleaned with water temperature at or near 150F.

Changing any parameter other than time or heat (do not exceed150 degrees) Viods the warranty.

6. Timer (run time) setting

The controller is preset to run for four hours. Most parts take one to two hours to clean, but varying levels of geometric complexity can

increase (or reduce) the time necessary. To set the run time different from that preset:

(1) Press and hold the for 2 seconds. When is displayed release the .

(2) Press to display hour and minutes .

(3) Press and hold while using the and keys to adjust the desired run time.

(4) Press to exit the menu.

Operation (continued)

CleanStation Dimension SRS-DT3

Jet action cleaning

7. Cleaning parts

IMPORTANT: Always wear neoprene safety gloves and eye protection while handling concentrate. Follow the instructions on the

bottle of solution concentrate from Stratasys. Please review the MSDS provided by Stratasys.

(1) Carefully open one 2.1lb bottle of WaterWorks Soluble Concentrate P400SC. Slowly add 1/2 of the bottle into the tank while the

pump is recirculating. If solution is not in granular form, break it up so that it can be added at a consistent rate. ALWAYS add

concentrate to water, NEVER add water to concentrate.

(2) Wait five minutes (for most of the concentrate to dissolve).

(3) Place parts directly into the tank or basket.

(4) Check the tank periodically. If the tank level drops significantly one or two inchs due to evaporation, add more water. DO NOT

add more cleaning solution.

(5) If the part or parts will not fit inside the basket but, will fit inside the tank, the basket can be removed from the lid by removing

the four 10-32 x 3/8” stainless screws. Reinstall the screws into the lid for later use.

8. Removing parts

IMPORTANT: Always wear neoprene safety gloves and eye protection while removing parts from the tank.

Parts may also be removed by using stainless steel or plastic tongs. DO NOT use aluminum tongs. Rinse parts with water until

their surfaces do not feel slippery. Dry parts with paper towels or let air-dry.

The solution may be used for cleaning additional parts. Cleaning times are faster with fresh cleaning solution. Change the solution

whenever the water gets too dark (coffee color) or cleaning times become noticeably longer.

Operation (continued)

CleanStation Dimension SRS-DT3

Jet action cleaning

9. Disposal of soluble solution

Method 1: Dilution

You may dispose of used solution by pouring it down the drain while simultaneously running tap water from the faucet. A 5-to-1

ratio (5 parts water to 1 part solution) is required to reduce the pH content to typical wastewater standards. Check local requirements

and modify this ratio accordingly.

Method 2: Neutralization

Malic acid may be used to neutralize the pH content of the solution. Using neoprene safety gloves and protective eye goggles, slowly

add 270 ml of malic acid to the tank before draining. Litmus paper (or an alternative pH indicator) may be used to determine if the

pH value of the solution is within local wastewater requirements. An alternative would be to drain the solution into a container big

enough to handle the full capacity of CleanStationTM. At that point mix in 270 ml of malic acid and dispose.

The Stratasys soluble solution is specially formulated to be safely disposed of by standard wastewater disposal procedures. PM

Technologies and Stratasys cannot anticipate local, state or international regulatory statutes. PM Technologies and Stratasys

recommend that disposal procedures be verified by the proper authorities in your region. PM Technologies and Stratasys cannot be

held liable if the solution is not disposed of properly.

10. Draining the tank

To drain the tank, check to make sure the power cord is unplugged and that a drain line is securely connected to the valve. Open the

drain valve until all of the water has emptied. Close the drain valve when not in use. If neutralizing with malic acid, a filmy residue

may remain in the tank which may be wiped off with paper towels.

Operation (continued)

CleanStation Dimension SRS-DT3

Jet action cleaning

Maintenance

(1) Unplug and drain the CleanStationTM per the Operating instruction step 10

(remember to wear safety protection).

(2) Remove and dry the tank lid before placing on another surface. If

removing the material does not increase the circulation move onto step 3.

(3) Inspect the suction strainer (see Figure 4) and remove any material

deposits. It maybe necessary to replace the strainer if the mesh becomes

excessively coated with deposits.

(4) Using a 7/16" socket, loosen (but do not remove) the 1/4"-20 nuts (see

Figure 4) located behind the holes at the top of the jet plate. Remove the jet

plate by lifting using the top holes provided for the 1/4”-20 nuts. As with the

tank lid, dry before setting aside.

(5) If a significant amount of material is found and removed from the suction

strainer, the manifold may not need cleaning; skip to step (9) to re-install the jet

plate. If the manifold appears to have material blocking the holes, proceed to

the next step (6) to remove and clean the manifold.

(6) Using a 5/16" socket, loosen the hose clamp connecting the manifold the

the hose and remove the 8-32 nuts with a 3/8” socket. Then completely remove

the pipe clamps and manifold (see Figure 4). Figure 4

jet plate

strainer

•There may be a periodic need to clean the pump suction strainer or manifold that

distributes the circulating water. If you notice a significant decrease in the circulation

of water, there may be a buildup of material blocking circulation flow.

IMPORTANT: Always unplug the CleanStationTM from its power source before doing any maintenance.

Manifold

2ea 10-32 BHCS

2ea 1/4-20 nuts

CleanStation Dimension SRS-DT3

Jet action cleaning

•The CleanStationTM requires very little maintenance. Keep it clean by wiping it down with a damp cloth after use. Remember to

always use neoprene safety gloves and eye protection.

•The CleanStationTM pump and motor are factory sealed and do not require any lubrication or seal replacement.

•When replacing fuses, always unplug power to the CleanStationTM and keep the power cord in view. Keeping the power cord in view

will ensure the CleanStationTM is not inadvertently plugged back in by someone else.

•Any failure of the product due to negligence or misuse by the Customer voids the warranty. Using the machine for anything other

than its intended purpose or changing anything that results in a failure also voids the warranty. Changing any control parameter

other than time and temperature (do not exceed 150 degrees) voids the warranty. The Customer is expected to follow the

guidelines for operations stipulated in the Installation, Operation, and Maintenance Instructions.

Maintenance (continued)

(7) Remove material blocking the jets by either pulling the material through the holes, or flushing through the inlet of the

manifold.

(8) Re-install the manifold and tighten the hose clamp.

(9) Re-install the jetplate. Slide the jet plate between the washers and the tank. Be careful not to over-tighten the nuts, for easier

removal in the future.

Table of contents

Popular Vacuum Cleaner manuals by other brands

Bissell

Bissell LittleGreen Proheat 1425 Series user guide

Panasonic

Panasonic MC-YL637S147-AE Service manual

NEFF

NEFF N17XH10 0 Series instruction manual

LG A9 Series owner's manual

Oreck

Oreck Cordless Captura BK51700 Series user guide

Kogan

Kogan KAVACROBVWA user manual

Kränzle

Kränzle VENTOS 50 ID Use and maintenance

EVVO

EVVO Ai35 instruction manual

DeWalt

DeWalt DWH200D instruction manual

Pontec

Pontec Pondomatic Vacuum Cleaner operating instructions

Cleanmaxx

Cleanmaxx PC-P007E instruction manual

Exido

Exido 240-114 manual

RIDGID

RIDGID WD1685AU0 owner's manual

Ezviz

Ezviz RE4P manual

STG global

STG global TANVAC HDV3000 Operator's manual

Shark

Shark ROTATOR PRO COMPLETE NV550 Series manual

Factory

Factory M3340 operating manual

Shop-Vac

Shop-Vac VN92 SERIES user manual