Clarke CWL460 Instruction Manual
OPERATION & MAINTENANCE
INSTRUCTIONS
ORIGINAL INSTRUCTIONS GC0621
18” VARIABLE SPEED WOOD LATHE
MODEL NO: CWL460
PART NO: 6501661
2
INTRODUCTION
Thank you for purchasing this CLARKE 18” Variable Speed Wood Lathe.
Before attempting to operate the machine, it is essential that you read this
manual thoroughly and carefully follow all instructions given. In doing so you
will ensure the safety of yourself and that of others around you, and you can
also look forward to the product giving you long and satisfactory service.
GUARANTEE
This CLARKE product is guaranteed against faulty manufacture for a period of
12 months from the date of purchase. Please keep your receipt as proof of
purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not affect your statutory rights.
SPECIFICATIONS
Weight 33 kg
Dimensions (L x W x H) 990 x 250 x 410 mm
Speed 650 - 3800 rpm (Variable)
Distance Between Centres 460 mm
Turning Capacity 304 mm
Tool Rest 148mm
Headstock Arbour Thread Size 1” 8 RH thread
IP (Ingress Protection) Rating IP 54
Motor Voltage/Frequency 230V / 50Hz
Rated Input Wattage 550 W
Sound Pressure Level (Lp) No load 61.3 / loaded 78.7 dB(A)
Sound Power Level Measured (Lw) No load 74.3 / loaded 91.7 dB(A)
3
SAFETY WARNINGS
WORK ENVIRONMENT
1. Keep the work area clean, tidy and well lit. Cluttered and dark areas invite
accidents.
2. DO NOT operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
3. Keep children and bystanders away while operating a power tool. Anyone
entering the work area must wear personal protective equipment.
Distractions can cause you to lose control and fragments of work may fly
away and cause injury.
4. Store power tools properly when not in use. Abrasive products should be
stored in a dry, secure place out of the reach of children.
5. Please read these instructions carefully and retain for future reference.
ELECTRICAL SAFETY
1. Power tool plugs must match the outlet. NEVER modify the plug in any way.
DO NOT use adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce the risk of electric
shock.
2. This machine is designed for indoor environments and must not be used for
other purposes. DO NOT expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric shock.
3. DO NOT abuse the power cable. NEVER use the cable for carrying, pulling
or unplugging the power tool. Keep the cable away from heat, oil, sharp
edges or moving parts. Damaged or entangled cables increase the risk of
electric shock.
4. Position the power cable so that it cannot be inadvertently pulled or
pinched, and where it does not cause a trip hazard.
5. Before cleaning or maintenance operations, always unplug the machine
from the power supply.
CAUTION: FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN
PERSONAL INJURY, AND/OR DAMAGE TO PROPERTY.
4
PERSONAL SAFETY
1. Stay alert, watch what you are doing and use common sense when
operating a power tool. DO NOT use a power tool while you are tired or
under the influence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in personal injury.
2. Use personal protective equipment. ALWAYS wear eye protection. Safety
equipment such as dust mask, non-skid safety shoes, hearing protection
and a workshop apron capable of stopping small abrasive or workpiece
fragments.
3. AVOID accidental starting. Ensure the switch is in the off position before
plugging in. Plugging in power tools that have the switch on invites
accidents.
4. Remove any adjusting key or drift rod before turning the power tool on. A
wrench or drift rod left attached to a rotating part of the power tool may
result in personal injury.
5. DO NOT overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
6. Keep your hair and clothing away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving parts.
7. Regularly clean the power tool’s air vents. The motor fan will draw dust
inside the housing and accumulation of material could cause electrical
hazards.
8. AVOID operator fatigue. Stop the power tool at regular intervals for a short
break to rest hands and arms.
9. Maintain your tools. Keep all handles and grips dry and clean.
10. If the machine requires repair, always contact your CLARKE dealer. Always
insist on original spare parts. Repairs carried out by unauthorized persons
may be dangerous and invalidate the guarantee.
11. This machine must only be used by adults. Children should not be allowed
to play with this appliance.
POWER TOOL USE AND CARE
1. DO NOT force the machine.Use the correct power tool for your
application. It will do a better and safer job at the rate for which it was
designed.
2. DO NOT use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and
must be repaired.
5
3. Disconnect the power tool from the power supply before making any
adjustments, changing accessories, or storing the tool. These measures will
reduce the risk of the power tool starting accidently.
4. Store power tools out of the reach of children and DO NOT allow persons
unfamiliar with the tool or these instructions to operate the power tool.
Power tools are potentially dangerous in the hands of untrained users.
5. Maintain power tools in top condition. Keep tools/ machines clean for the
best and safest performance. Check for misalignment or binding of
moving parts, broken parts, or any condition that may affect the power
tool’s operation. If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.
6. Use recommended accessories. The use of improper accessories could be
hazardous.
7. Machine cleanliness. DO NOT allow the ventilation slots in the machine to
become blocked with dust.
8. Check the power tool for damage before using the machine. Any
damaged part should be inspected to ensure that it will operate properly
and perform its intended function. Check for alignment of moving parts,
breakage of parts, mountings, and any other condition that may affect the
machine’s operation. Any damage should be properly repaired or the part
replaced. If in doubt, DO NOT use the machine. Consult your local CLARKE
dealer.
SERVICING
1. When necessary, have your power tools serviced or repaired by a qualified
person using identical replacement parts. This will ensure that the safety of
the power tool is maintained.
ADDITIONAL PRECAUTIONS FOR WOOD LATHES
1. ALWAYS familiarise yourself with wood lathes and turning techniques before
using the machine. If there is any doubt whatsoever you should consult a
qualified person.
2. ALWAYS store chisels safety when you have finished with the machine.
3. CAUTION: This machine is designed for use with woodturning chisels only.
4. NEVER attempt to turn a workpiece unless a suitable support is used.
WARNING: DUST GENERATED FROM CERTAIN MATERIALS CAN BE
HAZARDOUS TO YOUR HEALTH. ALWAYS OPERATE THE LATHE IN A WELL
VENTILATED AREA. USE A DUST COLLECTION SYSTEM WHENEVER
POSSIBLE.
6
5. ALWAYS stop the lathe before removing workpieces, work supports or swarf
from the table.
6. ALWAYS be sure that the workpiece is securely locked in position
7. ALWAYS keep hands and fingers away from the moving workpiece.
SAFETY SYMBOLS
The following safety symbols may be found on the machine.
ENVIRONMENTAL PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All
unwanted accessories and packaging should be sorted and taken to a
recycling centre for disposal in a manner which is compatible with the
environment.
ENVIRONMENTAL RECYCLING POLICY
Through purchase of this product, the customer is taking on the
obligation to deal with the WEEE in accordance with the WEEE
regulations in relation to the treatment, recycling & recovery and
environmentally sound disposal of the WEEE.
In effect, this means that this product must not be disposed of with general
household waste but according to the laws governing Waste Electrical and
Electronic Equipment (WEEE) at a recognised disposal facility.
Fully read this
manual and safety
instructions before
use
Eye protection
should be worn
Ear protection
should be worn
Dust mask should be
worn
Indoor Use Only
7
ELECTRICAL CONNECTIONS
Before switching the product on, make sure that the voltage of your electricity
supply is the same as that indicated on the rating plate. This product is
designed to operate on 230VAC 50Hz. Connecting it to any other power
source may cause damage.
This product may be fitted with a non-rewireable plug. If it is necessary to
change the fuse in the plug, the fuse cover must be refitted. If the fuse cover
becomes lost or damaged, the plug must not be used until a suitable
replacement is obtained.
If the plug has to be changed because it is not suitable for your socket, or due
to damage, it should be cut off and a replacement fitted, following the wiring
instructions shown below. The old plug must be disposed of safely, as insertion
into a mains socket could cause an electrical hazard.
If the colours of the wires in the power cable of this product do not correspond
with the markings on the terminals of your plug, proceed as follows.
•TheBlue wire must be connected to the terminal which is marked Nor
coloured Black.
•TheBrown wire must be connected to the terminal which is marked Lor
coloured Red.
•TheYellow and Green wire must be connected to the terminal which is
marked E or or coloured Green.
We strongly recommend that this machine is connected to the mains supply
via a Residual Current Device (RCD)
If in any doubt, consult a qualified electrician. DO NOT attempt any repairs
yourself.
WARNING! Read these electrical safety instructions thoroughly
before connecting the product to the mains supply.
Plug must be BS1363/A approved.
Always fit a 13 Amp fuse.
Ensure that the outer sheath of the cable is firmly held by the clamp
Neutral
(Blue)
Live
(Brown)
Earth
(Green and Yellow)
8
OVERVIEW
Ensure the wood lathe and its components suffered no damage during transit
and that all components are present. Should any loss or damage be
apparent, please contact your CLARKE dealer immediately.
The following components are supplied with the lathe assembly.
Item Description Item Description
1 Handwheel 10 Tailstock Centre Cup
2 LED Variable Speed Display 11 Tailstock
3 Headstock 12 Tail Axis Locking Handle
4 Faceplate 13 Tail Axis Adjusting Wheel
5 Headstock Centre Spur 14 Drift Rod
6 Tool Rest 15 On/Off & Speed Control
7 Tool Rest Locking Handle 16 Motor
8 Tool Rest Base Locking Handle 17 Bed
9 Tool Rest Base 18 3 x Hex Keys (3mm,6mm,8mm)
Not Shown
9
1. Fit the tailstock centre cup into
the tail axis.
NOTE: To detach the tailstock
centre cup, place the drift
rod into the adjusting wheel
as far as it goes and give it a
tap.
2. Fit the tool rest into the tool rest
base. Adjust to the required
height and position using the rest
locking handle and base locking
handle.
3. Install the headstock faceplate by
screwing it onto the headstock
spindle, using the drift rod as a
counter lever. Lock the faceplate
into place using the 2 x 3mm hex
grub screws.
NOTE: The faceplate has 4 screw
holes evenly spaced. These
are for securing workpieces
that do not require the
tailstock for support.
4. Install the headstock centre spur
by placing it into the headstock
spindle as shown
NOTE: To detach the headstock
centre spur, place the drift
rod into the hand wheel as
far as it goes and give it a
tap.
10
OPERATION
1. Always rotate the workpiece by hand before turning on the motor and
check it does not strike the tool/tool rest.
2. Ensure the tool rest and tailstock are securely locked in position before
starting work.
3. Always position the tool-rest just above the centre-line of the lathe.
4. Press the green push-button (I) to
start the lathe and adjust the
speed using the speed control
knob.
NOTE: Always use the lowest speed
when starting a new
workpiece, see Adjusting The
Belt Position on page 11.
5. The headstock spindle speed can
be monitored on the LED display
mounted on top of the
headstock.
6. Avoid turning timber which has
splits or substantial knots or voids
and take special care if these are
discovered.
7. When turning, always roughly turn
the work to a round form at slow
speed.
8. Take care that the turning tools do not bite suddenly into the workpiece.
This manual suits for next models
1
Table of contents
Other Clarke Lathe manuals
Clarke
Clarke WOODWORKER CWL325V Instruction Manual
Clarke
Clarke MetalWorker CL300M Installation and operation manual
Clarke
Clarke WOODWORKER CWL325V Manual
Clarke
Clarke CWL1000B Instruction Manual
Clarke
Clarke Woodworker CWL1000 Installation and operation manual
Clarke
Clarke CWL6B Installation and operation manual
Clarke
Clarke WOODWORKER CWL1000CF Instruction Manual
Clarke
Clarke Metalworker CL430 Installation and operation manual
Clarke
Clarke CWL435 Instruction Manual
Clarke
Clarke Woodworker CWL1000V Installation and operation manual
