Clarke CAT101 Manual

1/2” IMPACT WRENCH

MODEL No: CAT101

Part No: 3110857

OPERATION & MAINTENANCE

INSTRUCTIONS

0707

SPECIFICATIONS

Drive Size ................................................... 1/2” Square

Max Torque ............................................... 260 ft/lb (352 Nm)

Air Inlet ....................................................... 1/4” BSP

Ave. Air Consumption .............................. 4.5 cfm

Air Pressure Max ....................................... 6.2 bar

Noise Level ................................................ 94dB A

Vibration Level ......................................... 10.4m/s2

Net Weight ................................................ 2.23 kg

Dimensions LxWxH .................................... 220 x 70 x 200

Part No ....................................................... 3110857

Please note that the details and specifications contained herein, are correct at the time of

going to print. However CLARKE International reserve the right to change specifications at

any time without prior notice. Always consult the machine’s data plate

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of 12 months

from the date of purchase. Please keep your receipt as proof of purchase.

This guarantee is invalid if the product is found to have been abused or tampered with in

any way, or not used for the purpose for which it was intended.

Faulty goods should be returned to their place of purchase, no product can be returned

to us without prior permission.

This guarantee does not effect your statutory rights.

IN THE BOX

1 X 1/2” Impact wrench with 2” Anvil

1 X Instruction Book

SAFETY PRECAUTIONS

IMPORTANT

FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN PERSONAL INJURY,

AND/OR DAMAGE TO PROPERTY.

WORK ENVIRONMENT

• Keep the work area clean and tidy.

• Dress appropriately - Do not wear loose clothing or jewellery. Tie long hair out of

the way.

• Keep children and visitors away - Do not let children handle the impact wrench.

Make sure that any other persons in the work area are dressed suitably and are

wearing eye and ear protectors.

• Do not operate the impact wrench where there are flammable liquids or gases.

• Keep the air supply hose away from heat, oil and sharp edges.

• Do not fit the impact wrench to any stand or clamping device that may damage

the tool.

USE

• Stay alert and use common sense - Do not operate the impact wrench when you

are tired or under the influence of alcohol, drugs or medication.

• Always wear eye protectors when using the impact wrench - Eye protectors must

provide protection from flying particles from the front and the side.

• Always wear ear protectors when using the impact wrench.

• Do not overreach - Keep proper footing and balance at all times.

• Never use any type of bottled gas as a source of power for the impact wrench.

• Do not connect the air supply hose with your finger on the trigger of the impact

wrench.

• Do not exceed the maximum pressure for the impact wrench: 90 psi / 6 bar.

• Check hoses for leaks or worn condition before use, and ensure that all

connections are secure.

• Do not use the impact wrench for any other purpose than that described in this

book.

• Do not carry out any alterations or modifications to the impact wrench.

SAFETY PRECAUTIONS

• Always disconnect from the air supply when:

a) Performing any maintenance

b) The impact wrench is not in use.

c) The impact wrench will be left unattended.

d) Moving to another work area.

e) Passing the impact wrench to another person.

• Never use the impact wrench if it is defective or operating abnormally.

• The impact wrench should be serviced at regular intervals by qualified service

personnel.

• Avoid damaging the impact wrench for example by applying excessive force of

any kind.

• ALWAYS maintain the tool with care. Keep it clean for best and safest

performance.

• Quick change couplings should not be located at the tool. They add weight and

could fail due to vibration.

• DO NOT force or misuse the tool. It will do a better and safer job at the rate for

which it was designed.

• DO NOT remove any labels. Damaged labels should be replaced.

• This tool vibrates with use. Vibration may be harmful to your hands or arms. Stop

using the tool if discomfort, a tingling feeling or pain occurs. Seek medical advice

before resuming use.

• NEVER use standard sockets. These may shatter with serious consequences. Use

ONLY Impact sockets.

TRANSPORTATION

• Never carry the impact wrench by the air supply hose.

• Never carry the impact wrench with your finger on the trigger.

STORAGE

• When not in use the impact wrench must be disconnected from the air supply

and stored in a dry place out of the reach of children (preferably in a locked

cabinet).

• Avoid storing the impact wrench in environments where the temperature is below

0oC.

PARTS

Trigger

Air Regulator

Direction Selector

Anvil

AIR SUPPLY

WARNING!

COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU ARE THOROUGHLY

FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF COMPRESSORS AND

COMPRESSED AIR SUPPLY.

• Use only clean, dry, regulated compressed air as a power source for the impact

wrench.

• Air compressors used with the impact wrench must comply with the appropriate

European Community safety directives.

• A build up of moisture or oil in the air compressor will accelerate wear and

corrosion in the impact wrench.

• Never exceed the maximum operating pressure for the impact wrench.

AIR HOSE

• The air hose must be rated at least 150% of the maximum operating pressure of

the tool.

Air Inlet

RECOMMENDED AIR SUPPLY CONNECTION

ASSEMBLY

NOTE:

ensure the compressor is turned off.

1. Connect a suitable hose to the impact

wrench using a ¼” hose adapter.

2. Connect the other end of the hose to the

compressor.

3. Your impact wrench is now ready for use.

You can fit a whip hose with a quick fit coupling

if required (available from your Clarke dealer.)

WARNING!

COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU ARE THOROUGHLY

FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF COMPRESSORS AND

COMPRESSED AIR SUPPLY.

OPERATING INSTRUCTIONS

WARNING!

WAIT UNTIL THE ANVIL HAS STOPPED ROTATING BEFORE OPERATING THE

DIRECTION CONTROL SWITCH.

USING THE DIRECTIONAL CONTROL BUTTON

The direction control button should be used as follows.

1 For normal tightening, the impact wrench should be operated in the forward (F)

direction.

2 For loosening, the impact wrench should be operated in the reverse (R) direction.

Direction control button in

forward position Direction control button in

reverse position

FITTING THE IMPACT SOCKET

1 Select the impact socket you require

WARNING!

NEVER use standard sockets. These may

shatter with serious consequences. Use

ONLY Impact sockets.

2 Push the inpact socket onto the anvil

as shown.

OPERATING INSTRUCTIONS

ADJUSTING THE POWER

To adjust the power, set the

air regulator to one of the 4

settings avalaible.

1 (Low) - 4 (High).

DISCONNECTING THE AIR SUPPLY

Do not disconnect the air supply hose until the compressor has been shut down and the

compressed air released.

1. Refer to the compressor instruction book for the procedures to shut down and

release the compressed air.

2. Once the pressure has been released, disconnect the air supply hose from the

impact wrench.

3. Store the impact wrench safely in its box in a dry, secure environment

Squeeze

OPERATING THE IMPACT WRENCH

1. Locate the socket over

the nut to be tightened

or loosened.

2. Squeeze the trigger to

start the impact wrench.

3. Release the trigger to

stop the impact wrench.

Air Regulator

MAINTENANCE

WARNING! Make sure that the impact wrench is disconnected from the air supply before

starting any cleaning, or maintenance procedures.

Daily

• Drain water from air tank, air line and compressor.

• Pour a few drops of CLARKE Air Line Oil, into the air inlet. This should be carried out

regardless of whether or not an air line lubricator is used. If an Air line lubricator is not

used, this procedure should be repeated after every two to three hours of use.

Weekly

• Check the air inlet screen filter and clean if necessary.

• Remove the grub screw and insert a few drops of oil into the oil port on the side of

the impact wrench.

CLEANING

• Keep the body of the impact wrench clean and free from debris, Grit or gum

deposits in the tool may reduce efficiency.

SERVICE AND REPAIR

• All servicing and repair must be carried out by qualified service technicians.

NOTES

Please note that factors other than the tool may effect its operation and efficiency such

as reduced compressor output, excessive drain on the airline, moisture or restrictions in

the line, or the use of connectors of improper size or poor condition which will reduce air

supply.

**Clarke Air Line Oil is available from your CLARKE dealer part no. 3050825.

We declare that these products comply to the following standards/directives

• 98/37/EC

Model No: CAT101

Serial or Batch number: See product data plate

signature:

D. Kemp

ENGINEERING MANAGER

DECLARATION OF CONFORMITY

PARTS DIAGRAM

PARTS LIST

Index Part Description

No. No.

1 KL504W01 Housing

2 KL504W02 Valve Bushing

3 KL504W03 Reverse Valve

4 KL504W04 Trigger

5 KLSP007 Pin

6 KL504W06 Valve Stem

7 KL504W07 Air Inlet

8 KL504W08 Ball Seat

9 KL506AW43 Spring

10 KLAA065 Steel Ball

11 KL504W11 Cover

12 KL504W12 Air Regulator

13 KLSO016 O-Ring

14 KL504W14 Spring

16 KLSH028 Screw

17 KL504W171 Bushing

18 KL504W183 Anvil

19 KL504W19 Hammer Cage

20 KL504W20 Hammer Pin

21 KL504W21 Hammer Dog

22 KL504W22 Drive Cam

23 KLSP008 Pin

24 KL504W24 Cylinder

25 KL504W25 Rotor

26 KL504W26 Rotor Blade

27 KL504W27 Rear End Plate

28 KLCA6001 Ball Bearing

29 KL504W29 Front End Plate

30 KLSP006 Pin

31 KL504W31 Spring

32 KL504W32 Pin

33 KL504W33 Gasket

34 KL504W34 Rear Cover

35 KLSH0031 Screw& Spring Washer

36 KL504W37 Front Rubber

37 KL504W38 Exhaust Deflector

38 KLSH041 Screw

39 KLSH027 Screw

40 KL504W41 Anvil Collar

41 KLSO009 O-Ring

42 KL504W43 Rubber

43 KLSH045 Screw

44 KL504W45 Oil Seal

Index Part Description

No. No.

This manual suits for next models

Table of contents

Other Clarke Impact Driver manuals

Clarke

Clarke X-Pro CAT198 Installation and operation manual

Clarke

Clarke CAT117 Installation and operation manual

Clarke

Clarke CAT110 Instruction Manual

Clarke

Clarke CAT78 Installation and operation manual

Clarke

Clarke CAT102 Instruction Manual

Clarke

Clarke X-Pro CAT204 Installation and operation manual

Clarke

Clarke CAT48 Installation and operation manual

Clarke

Clarke CAT96 Instruction Manual

Clarke

Clarke CAT131 Installation and operation manual

Clarke

Clarke CAT154 Installation and operation manual

Clarke

Clarke CEW1100 Instruction Manual

Clarke

Clarke CEW520 Instruction Manual

Clarke

Clarke X-Pro CAT163 Installation and operation manual

Clarke

Clarke CAT79 Installation and operation manual

Clarke

Clarke CAT64 Installation and operation manual

Clarke

Clarke CIR24 Installation and operation manual

Clarke

Clarke CAT23C User manual

Clarke

Clarke CAT81 User manual

Clarke

Clarke CIR13C Installation and operation manual

Clarke

Clarke CIR13C Installation and operation manual

Clarke

Clarke CID20Li Instruction Manual

Clarke

Clarke CAT104 Instruction Manual

Clarke

Clarke CAT64 Instruction Manual

Clarke

Clarke CAT179 Installation and operation manual

Popular Impact Driver manuals by other brands

stayer

stayer IW500D operating instructions

Makita

Makita DTD152 instruction manual

Milwaukee

Milwaukee M12 FID Original instructions

Grizzly

Grizzly H6140 instruction sheet

Makita

Makita BTW450 user manual

Ozito

Ozito LID-3000 instruction manual

Astro Pneumatic Tool

Astro Pneumatic Tool 1812 manual

Greenlee

Greenlee HW3 Service manual

Sthor

Sthor 57091 manual

Makita

Makita DTD145 instruction manual

Hilti

Hilti SIW 2-A12 manual

Ryobi

Ryobi R18IW3 Original instructions

Parkside

Parkside PDSSA 20-Li A1 Translation of the original instructions

Flex

Flex FX1471 Operator's manual

SATA

SATA 51075C operation instruction

Cembre

Cembre NR-11P Operation and maintenance manual

Makita

Makita BTP131RFE instruction manual

DeWalt

DeWalt XR Li-ion DCF902 instruction manual