Clarke CMB710 Instruction Manual

WARNING: Read these instructions before using the bender

OPERATION & MAINTENANCE

INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC06/23

710mm METAL BENDER

MODEL NO: CMB710

PART NO: 7610905

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Servi[email protected]om

INTRODUCTION

Thank you for purchasing this CLARKE Metal Bender. Before attempting to use

it please read this manual and carefully follow all instructions given. In doing so

you will ensure the safety of yourself and that of others around you, and you

can also look forward to the product giving you long and satisfactory service.

Ensure the product suffered no damage during transit and that all items are

present. Should any loss or damage become apparent, please contact your

CLARKE dealer immediately.

SAFETY PRECAUTIONS

As with all tools and workshop equipment it is necessary to exercise caution

when it is put to use, being aware of any associated or inherent dangers.

• Due to the weight of the metal bender, the help of an assistant may be

beneficial during unpacking and mounting.

• ALWAYS operate on a suitably strong bench with adequate light.

• This metal bender must be firmly secured to a firm and level bench using

suitable bolts (not supplied).

• Leave adequate working space around the bender for safer and

convenient operation.

• ALWAYS check for signs of structural damage before starting work. DO NOT

use if damage is found. Have repairs made only by a CLARKE service

centre.

• ALWAYS ensure the workpiece is secure and properly positioned before

applying pressure.

• ALWAYS keep hands and fingers away from moving parts that may pinch.

• NEVER use extension tubes to increase the length of the handles. Excessive

effort can cause damage and/or accidents.

• NEVER attempt to bend materials which exceed the sizes stated above.

Failure to heed these warnings may result in damage to the equipment or

personal injury.

Dimensions D x W x H 155 x 902 x 128 (+420mm handle) mm

Net Weight 17.9 kg

Bending Capacity Thickness-1.2mm Width 730mm Angle - 0-90o

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or [email protected]

METHOD OF USE

Mount the Metal Bender on a sturdy workbench at a height which allows easy

operation taking into account the nature of the work, with the handles

pointing towards you.

• 4 x10 mm bolts will be required (not supplied) for mounting to the chosen

bench. Holes will need to be drilled in the bench at the positions shown.

WARNING: NEVER EXCEED THE MAX BENDING CAPACITY (1.2mm MATERIAL).

1. Lower the handle until the moving plate becomes parallel to the

workbench.

2. Position the workpiece on the supporting plate and the moving plate so

that the edge to be bent lines up with the back edge of the supporting

plate.

3. Place the pressing plate on top of the supporting plate so that the back

edge of the Pressing Plate lines up flush with the back edge of the

Supporting Plate.

NOTE: To ensure a proper bend, leave a 2-3mm gap for 1.2mm material,

decrease the gap when using thinner material. Experiment with

scrap pieces.

4. Raise the two handles to bend the material.

WARNING: WHEN BENDING SHEET METAL, KEEP YOUR HANDS CLEAR OF THE

SUPPORTING AND MOVING PLATE TO AVOID INJURY.

If disposing of scrap metal, DO NOT dispose of with general waste. Metal

products and scrap should be taken to your local civic amenity site for the

recycling of metal products according to local regulations.

This manual suits for next models

Table of contents

Other Clarke Cutter manuals

Clarke

Clarke ETC8 Instruction Manual

Clarke

Clarke CAT127 Installation and operation manual

Clarke

Clarke CHT518 User manual

Clarke

Clarke TCM430 User manual

Clarke

Clarke CLC1 User manual

Clarke

Clarke WE6493A User manual

Clarke

Clarke ETC8 Instruction Manual

Clarke

Clarke 30SI Installation and operation manual

Clarke

Clarke ETC6 Installation and operation manual

Clarke

Clarke TCM420 User manual

Clarke

Clarke 1801518 User manual

Clarke

Clarke 20CI Instruction Manual

Clarke

Clarke ETC400 Troubleshooting guide

Clarke

Clarke ETC180 Quick reference guide

Clarke

Clarke ETC180 Manual

Clarke

Clarke Strong-Arm CS10HC Installation and operation manual

Clarke

Clarke X-Pro CAT203 Installation and operation manual

Clarke

Clarke CHT532 User manual

Clarke

Clarke ETC7 Installation and operation manual

Popular Cutter manuals by other brands

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Original instructions

Makita

Makita DCS552 instruction manual

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 user manual

Makita

Makita 4112HS instruction manual

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S manual

Hitachi

Hitachi CM 4SB2 Safety instructions and instruction manual

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 instruction manual

GCC Technologies

GCC Technologies AFJ-24S user manual

DeWalt

DeWalt XR LI-ION DCS350N manual

Baudat

Baudat ES1 instruction manual

Mafell

Mafell ZAF 200 Operating instructions and spare parts list

Makita

Makita 4100NH instruction manual

Formax

Formax FD 574 Operator's manual

EINHELL

EINHELL TE-MA 1500 Original operating instructions

Husqvarna

Husqvarna Cut-n-Break K 760 Operator's manual

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Operator's manual

TRI tool

TRI tool 301A user manual

Roller

Roller King 1 1/4 operating instructions